Toyota Tundra (2015 year). Manual — part 174
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000003YLU03DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type): Reverse
Signal Circuit; 2015 MY Tundra [08/2014 - ]
Reverse Signal Circuit
DESCRIPTION
The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1.
CHECK VEHICLE SIGNAL (OPERATION CHECK)
(a) Enter the "Function Check/Setting I" mode and select "Vehicle
Signal"
.
(b) Check that the display changes between ON and OFF according to the shift lever position.
PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (f...
OK:
SHIFT LEVER POSITION
DISPLAY
R
ON
Except R
OFF
HINT:
This display is updated once per second. As a result, it is normal for the display to lag behind the actual
shift lever position.
NG
GO TO STEP 2
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN
PROBLEM SYMPTOMS TABLE
2.
CHECK NAVIGATION RECEIVER ASSEMBLY
(a) Disconnect the navigation receiver assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J135-2 (REV) - Body ground
Ignition switch ON, shift lever in R
7.5 to 14 V
J135-2 (REV) - Body ground
Ignition switch ON, shift lever not in R
Below 1 V
Text in Illustration
*a
Result
RESULT
PROCEED TO
OK (for Column Shift Type)
A
OK (for Floor Shift Type)
B
NG
C
PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (f...
OK
B
REPLACE NAVIGATION RECEIVER ASSEMBLY
C
GO TO STEP 3
A
REPLACE NAVIGATION RECEIVER ASSEMBLY
3.
CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY -
PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
(a) Disconnect the J135 navigation receiver assembly connector.
(b) Disconnect the D35 park/neutral position switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J135-2 (REV) - D35-1 (RL)
Always
Below 1 Ω
J135-2 (REV) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
4.
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY -
BATTERY)
(a) Disconnect the park/neutral position switch assembly
connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (f...
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
D35-2 (RB) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
HINT:
*: Replace park/neutral position switch assembly procedure
for A760E:
for A760F:
for AB60E:
for AB60F:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE PARK/NEUTRAL POSITION SWITCH
ASSEMBLY*
PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (f...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст