Toyota Tundra (2015 year). Manual — part 788
(c) Using SST, disconnect the upper ball joint from the steering
knuckle.
SST: 09628-62011
(d) Remove the steering knuckle.
6. REMOVE KNUCKLE GREASE RETAINER CAP LH (for 2WD)
(a) Using a screwdriver and hammer, tap out the retainer cap.
7. REMOVE STEERING KNUCKLE OIL SEAL LH (for 4WD)
(a) Using a screwdriver and hammer, tap out the oil seal.
AXLE: STEERING KNUCKLE: REMOVAL; 2015 MY Tundra [08/2014...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000016X403YX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AXLE: STEERING KNUCKLE: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. INSTALL KNUCKLE GREASE RETAINER CAP LH (for 2WD)
(a) Using a brass bar and hammer, tap in a new retainer cap.
NOTICE:
The retainer cap is a non-reusable part.
Do not damage the retainer cap.
2. INSTALL STEERING KNUCKLE OIL SEAL LH
(a) Using SST and a press, press in a new oil seal.
SST: 09950-60020
09951-01030
SST: 09950-70010
09951-07100
NOTICE:
The oil seal is a non-reusable part.
Do not damage the steering knuckle oil seal.
3. INSTALL STEERING KNUCKLE LH
(a) Install the front suspension upper arm to the steering knuckle with the nut.
Torque:
110 N·m {1,122 kgf·cm, 81ft·lbf}
(b) Install a new clip.
HINT:
If the holes for the clip are not aligned, tighten the nut up to another 60.
4. CONNECT FRONT LOWER BALL JOINT ATTACHMENT LH
5. CONNECT TIE ROD END SUB-ASSEMBLY LH
6. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH
(a) Install the front axle hub
.
7. CONNECT FRONT SPEED SENSOR LH
AXLE: STEERING KNUCKLE: INSTALLATION; 2015 MY Tundra [0...
(a) Connect the front speed sensor to the steering knuckle with the
bolt.
Torque:
11 N·m {107 kgf·cm, 8ft·lbf}
(b) Attach the clip to the steering knuckle.
8. INSTALL FRONT WHEEL
Torque:
for Aluminum Wheel -
131 N·m {1336 kgf·cm, 97ft·lbf}
for Steel Wheel -
209 N·m {2131 kgf·cm, 154ft·lbf}
9. CHECK SPEED SENSOR SIGNAL
(a) Check the speed sensor signal
.
10. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light
.
11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(a) Inspect and adjust the front wheel alignment
.
AXLE: STEERING KNUCKLE: INSTALLATION; 2015 MY Tundra [0...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM00000306Y00JX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DIFFERENTIAL: AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR (for 4WD): COMPONENTS; 2015
MY Tundra [08/2014 - ]
COMPONENTS
ILLUSTRATION
DIFFERENTIAL: AUTOMATIC DISCONNECTING DIFFERENTIA...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст