Toyota Tundra (2015 year). Manual — part 1040
(c) Slide the clamp and disconnect the purge line hose.
(d) Disconnect the air inlet line hose.
(1) Push the air inlet line hose firmly toward the charcoal canister assembly.
(2) Pinch the air inlet line hose as shown in the illustration.
(3) Pull out the air inlet line hose.
NOTICE:
Do not use any tools in this procedure.
Check for any dirt and foreign matter contamination in the charcoal canister assembly and around the air
inlet line hose. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal
between the charcoal canister assembly and air inlet line hose.
(e) Disconnect the vent line hose.
(1) Pinch the retainer and raise it.
NOTICE:
Do not use any tools in this procedure.
Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if
necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and
connector.
(f) Detach the wire harness clamp.
(g) Remove the 4 bolts and charcoal canister assembly.
2. REMOVE CANISTER PUMP MODULE
(a) Before removing the canister pump module, clean the charcoal canister assembly by blowing air into it to
Make sure to clean the charcoal canister assembly using only air.
Do not use gasoline, thinners or solvents.
1UR-FE EMISSION CONTROL: CANISTER: REMOVAL; 2015 MY ...
(b) While disengaging the 2 claws as shown in the illustration, push
the canister pump module upwards using a screwdriver to
remove it.
(c) Check if the charcoal canister contains foreign matter such as mud or water.
(2) Hold the charcoal canister assembly upside down to make sure that the charcoal canister assembly is
1UR-FE EMISSION CONTROL: CANISTER: REMOVAL; 2015 MY ...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002HXQ034X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE EMISSION CONTROL: CANISTER: INSPECTION; 2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT CHARCOAL CANISTER ASSEMBLY
(a) Visually check the charcoal canister assembly for cracks or
damage.
If cracks or damage are found, replace the charcoal canister
assembly.
(b) Check charcoal canister assembly operation.
(1) With the purge port closed, blow 5 kPa (0.1 kgf/cm 2 , 0.7
Text in Illustration
*a
Vent Line Port
*b
Air Inlet Line Port
*c
Purge Line Port
*d
Air
If the result is not as specified, replace the charcoal canister
assembly.
(2) With the vent port closed, blow 5 kPa (0.1 kgf/cm 2 , 0.7
Text in Illustration
*a
Vent Line Port
*b
Air Inlet Line Port
*c
Purge Line Port
*d
Air
If the result is not as specified, replace the charcoal canister
assembly.
1UR-FE EMISSION CONTROL: CANISTER: INSPECTION; 2015 M...
(c) Check for air leaks.
Text in Illustration
*1
Pressure Gauge
*a
Vent Line Port
*b
Air Inlet Line Port
*c
Purge Line Port
(2) With the purge line port and air inlet line port closed, apply 20 kPa (150 mmHg, 5.91 in.Hg) of
pressurized air into the vent line port, and then confirm that pressure is retained for 1 minute.
If the result is not as specified, replace the charcoal canister assembly.
(d) Check the canister pump module.
(1) Connect a positive (+) lead from the battery to terminal 5
and a negative (-) lead to terminal 1.
(2) Check that a clicking sound is heard from the canister pump module.
If the result is not as specified, replace the canister pump module.
1UR-FE EMISSION CONTROL: CANISTER: INSPECTION; 2015 M...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст