Toyota Tundra (2015 year). Manual — part 1440
(a) Engine Room Side:
(1) Disconnect the clamp and No. 3 hose.
(2) Using a clip remover, remove the clamp from the body
panel.
(b) Front Fender RH Inside:
(1) Disconnect the No. 3 hose from the air pump.
(2) Using a clip remover, remove the clamp from the body panel.
5. REMOVE AIR PUMP ASSEMBLY WITH BRACKET
(a) Disconnect the 2 air pump connectors and detach the 3 wire
harness claws.
(b) Remove the 2 bolts, 2 nuts and air pump.
6. REMOVE AIR PUMP INLET
3UR-FBE EMISSION CONTROL: AIR PUMP: REMOVAL; 2015 MY ...
air pump inlet.
7. REMOVE NO. 1 AIR INJECTION SYSTEM HOSE
(a) Remove the 2 No. 1 air injection system hoses.
8. REMOVE AIR PUMP ASSEMBLY
(a) Using a clip remover, detach the 2 clamps and remove the 2
air pump assemblies from the bracket.
(b) Disconnect the 6 air pump insulators.
3UR-FBE EMISSION CONTROL: AIR PUMP: REMOVAL; 2015 MY ...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM0000047ED00ZX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE EMISSION CONTROL: AIR PUMP: INSPECTION; 2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT AIR PUMP ASSEMBLY
(a) Check the heater resistance.
(1) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
1 (APH+) - 3 (APHG)
-20°C (-4°F)
4.4 to 20.0 Ω
-10°C (14°F)
3.9 to 18.0 Ω
0°C (32°F)
3.5 to 16.0 Ω
10°C (50°F)
3.2 to 15.0 Ω
20°C (68°F)
3.0 to 14.0 Ω
Text in Illustration
*a
Component without harness connected
(Air pump)
If the result is not as specified, replace the air pump
assembly.
3UR-FBE EMISSION CONTROL: AIR PUMP: INSPECTION; 2015 ...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000030YB020X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE EMISSION CONTROL: AIR PUMP: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL AIR PUMP ASSEMBLY
(a) Connect the 6 air pump insulators to the 2 air pump
assemblies and install the 2 air pump assemblies to the
bracket.
(b) Attach the 2 wire harness clamps to the bracket.
2. INSTALL NO. 1 AIR INJECTION SYSTEM HOSE
(a) Install the 2 No. 1 air injection system hoses to the air pump.
HINT:
Insert the hoses until the hose ends are aligned with the
stoppers.
3. INSTALL AIR PUMP INLET
(a) Connect the air pump inlet to the No. 1 air injection system
hoses to install it, and then slide the 2 clips onto the hoses.
HINT:
Insert the inlet until the inlet stoppers are aligned with the
hose ends.
(b) Install the 2 bolts.
3UR-FBE EMISSION CONTROL: AIR PUMP: INSTALLATION; 201...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст