Toyota Tundra (2015 year). Manual — part 792
(b) Using SST to hold the companion flange, remove the nut.
SST: 09330-00021
09330-00030
8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
(a) Using SST, remove the companion flange.
SST: 09950-30012
09951-03010
09953-03010
09954-03010
09956-03030
SST: 09955-03050
Text in Illustration
*a
Turn
*b
Hold
9. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
(a) Using SST, remove the oil seal.
SST: 09308-10010
10. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
(a) Using SST, remove the bearing (inner race).
SST: 09556-22010
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
(b) Remove the bearing spacer.
12. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK
(a) Remove the 2 bolts and 2 nut locks.
13. REMOVE REAR DIFFERENTIAL CASE ASSEMBLY
(a) Place matchmarks on the bearing cap and differential carrier.
Text in Illustration
*a
Matchmark
(b) Remove the 4 bolts and 2 differential bearing caps.
(c) Remove the differential case from the differential carrier.
HINT:
Tag the 2 case bearing outer races to show the location for
reassembly.
14. REMOVE REAR DIFFERENTIAL DRIVE PINION
(a) Remove the differential drive pinion and bearing spacer from the
differential carrier.
15. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
(a) Using SST and a press, press out the bearing (inner race).
SST: 09950-00020
If either the drive pinion or ring gear is damaged, replace them
as a set.
16. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER
17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
(a) Using a brass bar and hammer, tap out the bearing (outer race).
If the bearing is damaged during removal, replace it.
18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING
(a) Using a brass bar and hammer, tap out the bearing (outer race).
If the bearing is damaged during removal, replace it.
19. REMOVE DIFFERENTIAL RING GEAR
(a) Place matchmarks on the ring gear and differential case.
Text in Illustration
*a
Matchmark
(b) Remove the 12 ring gear set bolts.
(c) Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.
20. INSPECT REAR DIFFERENTIAL CASE ASSEMBLY RUNOUT
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
HINT:
If the ring gear runout is within the specified value (see "INSPECT RUNOUT OF DIFFERENTIAL RING GEAR"
procedure), this inspection is not necessary.
(a) Install the differential case to the differential carrier.
(b) Inspect the differential case runout.
Maximum runout:
0.04 mm (0.00157 in.)
(c) Remove the differential case from the differential carrier.
21. REMOVE REAR DIFFERENTIAL CASE BEARING
(a) Using SST, remove the 2 bearings.
SST: 09950-40011
09951-04010
09952-04010
09953-04020
09954-04010
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00480
HINT:
(a) Using a pin punch and hammer, tap out the straight pin.
(b) Remove the pinion shaft, 2 pinion gears, 2 pinion gear thrust washers, 2 side gears and 2 side gear thrust
washers.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 1UR-...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст