Toyota Tundra (2015 year). Manual — part 957
A
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000003UTZ06HX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Satellite Radio Broadcast cannot be Selected or After
Selecting Broadcast, Broadcast cannot be Added into Memory; 2015 MY Tundra [08/2014 - ]
Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast cannot be
Added into Memory
INSPECTION PROCEDURE
NOTICE:
Some satellite radio broadcasts require payment. A contract must be made between a satellite radio
company and the user. If the contract expires, the broadcast will not be able to be listened to or viewed.
PROCEDURE
1.
CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
(a) Check the radio condition.
OK:
Broadcast can be selected, but selection cannot be memorized.
Result
RESULT
PROCEED TO
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
2.
CHECK SATELLITE RADIO
36 channels have already been preset.
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Satellite Radio B...
NG
GO TO STEP 3
OK
END (ONLY 36 CHANNELS CAN BE PRESET)
3.
CHECK BATTERY
(a) Check if the battery was replaced.
OK:
Battery was not replaced.
Result
RESULT
PROCEED TO
OK (for Column Shift Type)
A
OK (for Floor Shift Type)
B
NG
C
B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
C
GO TO STEP 4
A
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
4.
ADD PRESET CHANNEL INTO MEMORY AGAIN
(a) Check if the preset channels that have been cleared can be added into memory again.
OK:
Preset channels can be added into memory.
NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN
PROBLEM SYMPTOMS TABLE
OK
END
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Satellite Radio B...
OK
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000000NL5118X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Noise Occurs; 2015 MY Tundra [08/2014 - ]
Noise Occurs
INSPECTION PROCEDURE
PROCEDURE
1.
NOISE CONDITION
(a) Check from which direction the noise comes (front left or right, or rear left or right).
OK:
GO TO STEP 3
2.
CHECK SPEAKERS
Result
CONDITION
PROCEED TO
No malfunction is found
A
A speaker is installed incorrectly
B
Foreign matter is in a speaker
C
A speaker cone paper is broken
D
B
REINSTALL SPEAKER
C
REMOVE FOREIGN OBJECT
D
REPLACE SPEAKER
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Noise Occurs; 2...
A
3.
CHECK NOISE CONDITIONS
(a) Check the noise condition.
HINT:
The radio has a noise prevention function to reduce noise when listening to the radio. If a loud noise
occurs, check whether the ground at the antenna mounting base and the noise prevention unit are
installed and wired correctly.
CONDITION UNDER WHICH NOISE OCCURS
NOISE SOURCE
Noise increases when the accelerator pedal is depressed, but stops when the
engine is stopped.
Generator
Noise occurs during A/C or heater operation.
Blower motor
Noise occurs when the vehicle accelerates rapidly on an unpaved road or after the
ignition switch is turned ON.
Fuel pump
Noise occurs when the horn switch is pressed and released or when pressed and
held.
Horn
Noise occurs during window washer operation.
Washer
Noise occurs while the engine is running, and continues even after the engine is
stopped.
Engine coolant temperature
sensor
Noise occurs during wiper operation.
Wiper
Noise occurs when the brake pedal is depressed.
Stop light switch
Other
Static electricity
HINT:
The noise source cannot be determined.
NG
REPAIR OR REPLACE NOISE SOURCE
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN
PROBLEM SYMPTOMS TABLE
AUDIO / VISUAL: AUDIO AND VISUAL SYSTEM: Noise Occurs; 2...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст