Toyota Tundra (2015 year). Manual — part 468
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
HINT:
The shift solenoid valve S3 is turned ON/OFF normally when the shift lever is in D:
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve S3
ON
ON
ON
OFF
OFF
OFF
PROCEDURE
1.
INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S3)
(a) Disconnect the D83 transmission wire connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
A760F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISS...
OK
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
9 (S3) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration
*a
Component without harness connected
(Transmission Wire)
NG
GO TO STEP 3
2.
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
(a) Disconnect the D74 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D74-3 (S3) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration
*a
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE ECM
3.
INSPECT SHIFT SOLENOID VALVE S3
A760F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISS...
NG
REPLACE SHIFT SOLENOID VALVE S3
OK
REPAIR OR REPLACE TRANSMISSION WIRE
A760F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISS...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W8C08TX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0982,P0983; Shift Solenoid
"D" Control Circuit Low (Shift Solenoid Valve S4); 2015 MY Tundra [08/2014 - ]
DTC
P0982
Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)
DTC
P0983
Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)
DESCRIPTION
solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated
safely. Also, the ECM stops sending current to the open or short-circuited solenoid
.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0982
ECM detects a short in the solenoid valve S4 circuit 2 times when
solenoid valve S4 is operated (1-trip detection logic).
Short in shift solenoid
valve S4 circuit
Shift solenoid valve S4
ECM
P0983
ECM detects an open in the solenoid valve S4 circuit 2 times when
solenoid valve S4 is not operated (1-trip detection logic).
Open in shift solenoid
valve S4 circuit
Shift solenoid valve S4
ECM
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve S4 circuit. When there is an open or short circuit
in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When
the shift solenoid valve S4 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift
solenoid valve S4 circuit.
When the shift solenoid valve S4 is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open
in the shift solenoid valve S4 circuit
.
MONITOR STRATEGY
Related DTCs
P0982: Shift solenoid valve S4/Range check (Low resistance)
P0983: Shift solenoid valve S4/Range check (High resistance)
Required sensors/Components
Shift solenoid valve S4
A760F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст