Toyota Tundra (2015 year). Manual — part 761
(a) Detach the 2 claws and remove the shift lock solenoid bracket.
(b) Remove the screw, collar, 2 bushes and shift lock solenoid with
No. 1 shift lock plate sub-assembly from the column shift control
shift lever retainer.
(c) Insert a thin-bladed screwdriver, release the locking lug of
terminal 1 (SLS+) and 8 (E), and pull the terminals out from the
rear.
7. DISCONNECT NO. 1 SHIFT LOCK PLATE SUB-ASSEMBLY
(a) Using a pin-punch and hammer, tap out the spring pin and
disconnect the shift lock plate from the shift lock solenoid.
8. REMOVE TRANSMISSION CONTROL SWITCH (S POSITION)
AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY ...
(a) Remove the 2 screws and switch from the column shift control shift lever retainer.
(b) Insert a thin-bladed screwdriver, release the locking lug of
terminal 6 (IG) and 13 (S), and pull the terminals out from the
rear.
9. REMOVE TRANSMISSION CONTROL SWITCH (P
POSITION)
(a) Remove the 2 screws and switch from the column shift control
shift lever retainer.
AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY ...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM0000030G501BX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (for Column Shift Type): INSPECTION;
2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY
(a) Disconnect the transmission control switch connector.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
6 (IG) - 13 (S)
Shift lever position S, "+" and
"-"
Below 1 Ω
5 (SFTU) - 11
(E)
Shift lever position continuously
shifted to "+" (Up-shift)
4 (SFTD) - 11
(E)
Shift lever position continuously
shifted to "-" (Down-shift)
6 (IG) - 13 (S)
Shift lever position not on S, "+"
and "-"
10 kΩ or higher
5 (SFTU) - 11
(E)
Shift lever position S
4 (SFTD) - 11
(E)
If the result is not as specified, replace the column shift shift
lever sub-assembly.
AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY ...
Last Modified: 9-16-2014
6.6 N
Doc ID: RM000002IKO01FX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (for Column Shift Type): ADJUSTMENT;
2015 MY Tundra [08/2014 - ]
ADJUSTMENT
1. INSPECT SHIFT LEVER POSITION
(a) When moving the shift lever from the N position to other positions, check that the lever can be shifted
smoothly and accurately to each position and that the position indicator comes on in accordance with the
shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
2. ADJUST SHIFT LEVER POSITION
(a) Move the shift lever to the N position.
(b) Fold back the transmission control cable adjust case cover. Then
while sliding the slider toward the cable end side, press the lock
piece from the back side to release the lock.
(c) Check that the adjust case's spring is applying enough tension
to the shift control cable. Then press the lock piece to set the
lock.
NOTICE:
Use your hand to push the lock piece. Do not use any tools.
Securely push the lock piece so that the slider's protrusion is
above the lock piece.
AB60F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст