Toyota Tundra (2015 year). Manual — part 1739
2.0 to 3.0 mm (0.0787 to 0.118 in.)
NOTICE:
Remove any oil from the contact surface.
Install the engine rear oil seal retainer within 3 minutes and tighten the bolts and nuts within 15
minutes after applying seal packing.
(b) Install the oil seal retainer with the 6 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
NOTICE:
(c) Install the oil strainer with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
NOTICE:
Make sure the O-ring is not twisted or damaged.
7. INSTALL NO. 1 OIL PAN BAFFLE PLATE
(a) Install the baffle plate with the 7 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
8. INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
(a) Apply seal packing in a continuous line as shown in the illustration.
Seal packing:
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.157 in.)
NOTICE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal
packing.
(b) Install the oil pan with the 14 bolts and 2 nuts.
Torque:
for bolt A -
10 N·m {102 kgf·cm, 7ft·lbf}
for bolt B -
35 N·m {357 kgf·cm, 26ft·lbf}
for nut -
35 N·m {357 kgf·cm, 26ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after installing.
9. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
(a) Apply seal packing in a continuous line as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.156 in.)
NOTICE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal
packing.
(b) Install the oil pan with the 14 bolts and 2 nuts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after installing.
10. INSTALL NO. 1 HEAT EXCHANGER COVER
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
(a) Apply seal packing in a continuous line as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.157 in.)
NOTICE:
Remove any oil from the contact surface.
Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes
after applying seal packing.
(b) Install the heat exchanger cover with the 12 bolts and 2 nuts.
Torque:
for bolt C -
10 N·m {102 kgf·cm, 7ft·lbf}
except bolt C -
21 N·m {214 kgf·cm, 16ft·lbf}
Standard Bolt:
ITEM
LENGTH
THREAD DIAMETER
Bolt A
20 mm (0.787 in.)
8 mm (0.315 in.)
Bolt B
70 mm (2.76 in.)
8 mm (0.315 in.)
Bolt C
16 mm (0.630 in.)
6 mm (0.236 in.)
NOTICE:
Do not start the engine for at least 2 hours after installing.
11. INSTALL VENTILATION PIPE GASKET
(a) Using SST, evenly tap in a new ventilation pipe gasket until
09951-00360
SST: 09950-70010
09951-07100
NOTICE:
Do not tap the gasket at an angle.
Do not tap the gasket excessively.
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
12. INSTALL CYLINDER BLOCK WATER JACKET
SPACER
(a) Install the 2 water jacket spacers as shown in the illustration.
NOTICE:
Face the cutouts indicated by the arrows in illustration away
from the engine.
Face the "up mark" as shown in the illustration.
13. INSTALL CYLINDER HEAD GASKET RH
14. INSTALL CYLINDER HEAD GASKET LH
15. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH
16. INSTALL CYLINDER HEAD SUB-ASSEMBLY LH
17. INSTALL VALVE STEM CAP
18. INSTALL VALVE LASH ADJUSTER ASSEMBLY
(a) Inspect the valve lash adjuster
.
(b) Install the 32 valve lash adjusters to the cylinder head.
NOTICE:
Install the lash adjuster at the same place it was removed from.
19. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
(a) Apply engine oil to the lash adjuster tips and valve stem cap ends.
(b) Install the 32 valve rocker arms as shown in the illustration.
20. INSTALL CAMSHAFT BEARING CAP RH
housing.
HINT:
Check the identification mark stamped on the camshaft.
ITEM
MARK
for Intake Side
NO. 1
for Exhaust Side
NO. 2
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст