Toyota Tundra (2015 year). Manual — part 1874
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0011
P0021
Intake valve timing is not adjusted in valve timing advance
range
(1 trip detection logic)
Valve timing
OCV for intake camshaft
OCV filter
Intake camshaft timing
gear
ECM
P0012
P0022
Intake valve timing is not adjusted in valve timing retard
range
(2 trip detection logic)
Valve timing
OCV for intake camshaft
OCV filter
Intake camshaft timing
gear
ECM
MONITOR DESCRIPTION
The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the
intake camshaft. The VVT system includes the ECM, Oil Control Valve (OCV) and VVT controller. The
ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure
supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timings is large, and changes in the actual
intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores
DTC(s).
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0011,P0012...
Example:
A DTC is set when the following conditions "A" and "B" are met:
(a)It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").
(b)After the above condition is met, the camshaft timing oil control valve assembly is forcibly
activated for 10 seconds (Condition "B").
DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the
Related DTCs
P0011: Advanced camshaft timing (for Bank 1)
P0012: Retarded camshaft timing (for Bank 1)
P0021: Advanced camshaft timing (for Bank 2)
P0022: Retarded camshaft timing (for Bank 2)
Required Sensors/Components
(Main)
VVT OCV and VVT Actuator
Required Sensors/Components
(Related)
Crankshaft position sensor, Camshaft position sensor and Engine
coolant temperature sensor
Duration
Within 10 seconds
MIL Operation
Advanced camshaft timing: Immediate
Retarded camshaft timing: 2 driving cycles
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not
present
P0010, P0020 (VVT Oil control valve)
P0016, P0018 (VVT System)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel
control)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
Battery voltage
11 V or more
Engine speed
500 to 4000 rpm
ECT
75 to 100°C (167 to 212°F)
TYPICAL MALFUNCTION THRESHOLDS
Advanced camshaft timing:
Both conditions are met:
-
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT
hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at advanced valve timing
Retarded camshaft timing:
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0011,P0012...
Both conditions are met:
-
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT
hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at retarded valve timing
If the difference between the target and actual camshaft timings is greater than the specified value, the
ECM operates the VVT actuator.
Then, the ECM monitors the camshaft timing change for 10 seconds.
MONITOR RESULT
Refer to CHECKING MONITOR STATUS
.
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
1.
Turn the ignition switch to ON and turn the Techstream on.
2.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
3.
Turn the ignition switch off and wait for at least 30 seconds.
4.
Turn the ignition switch to ON and turn the Techstream on [A].
5.
Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
6.
Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more [C].
NOTICE:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
7.
Idle the engine for 3 minutes or more [D].
8.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
9.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
10.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
11.
Input the DTC: P0011, P0012, P0021 or P0022.
12.
Check the DTC judgment result.
13.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0011,P0012...
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
Depress the accelerator pedal by a large amount.
14.
Idle the engine for 3 minutes or more [G].
15.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
16.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
17.
Check the DTC judgment result again.
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the following procedure.
18.
Perform a universal trip and check for permanent DTCs
.
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
19.
WIRING DIAGRAM
Refer to DTC P0010
.
INSPECTION PROCEDURE
HINT:
DTC P0011, P0012, P0021 or P0022 may be set when foreign objects in the engine oil are caught in
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0011,P0012...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст