Toyota Tundra (2015 year). Manual — part 1607
OK
OK
The A/C switch and all accessory switches should be off.
(c) Idle the engine.
DATA LIST
CONDITION
SPECIFIED
CONDITION
Short FT #1 + Long
FT #1
-15 to +15%
Short FT #2 + Long
FT #2
-15 to +15%
NG
INSPECT BRAKE BOOSTER ASSEMBLY
10.
CHECK IGNITION SYSTEM
(a) Perform ignition system On-vehicle Inspection
.
NG
REPAIR OR REPLACE MALFUNCTIONING PARTS,
COMPONENT AND AREA
11.
READ FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which
were present when the DTC was stored
.
Result
FREEZE FRAME DATA ITEM
FOR DTC P1605
RESULT
SUSPECTED AREA
PROCEED
TO
Calculate Load
Mass air flow meter
A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
Air fuel ratio sensor
Wire harness or
B
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P160...
A
A
FREEZE FRAME DATA ITEM
FOR DTC P1605
RESULT
SUSPECTED AREA
PROCEED
TO
connector
HINT:
*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than
the actual intake manifold pressure, the freeze frame data will show a low engine load value.
*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel
ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.
B
GO TO STEP 15
12.
CHECK MASS AIR FLOW METER
(a) Remove the mass air flow meter.
RESULT
PROCEED TO
Visible foreign matter is not present
A
Visible foreign matter is present
B
B
REPLACE MASS AIR FLOW METER
13.
CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
(a) Check the harnesses and connectors, referring to DTC P0102 inspection procedure
.
HINT:
REPAIR OR REPLACE HARNESS OR CONNECTOR
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P160...
OK
14.
PERFORM DRIVE TEST
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature stabilizes.
HINT:
The A/C switch and all accessory switches should be off.
(c) Idle the engine.
DATA LIST
SPECIFIED CONDITION
Calculate Load
RESULT
PROCEED TO
Abnormal
A
Normal
B
B
GO TO STEP 18
A
REPLACE MASS AIR FLOW METER
15.
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME
FOR A/F SENSOR)
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P160...
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Start the engine, turn off all accessory switches and warm up the engine until the engine
coolant temperature stabilizes.
(d) Idle the engine.
(e) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection
Volume for A/F Sensor.
(f) Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel
injection volume.
Standard:
TECHSTREAM DISPLAY
SPECIFIED CONDITION
Control the Injection Volume for A/F Sensor
(+12.5%)
Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%)
Air fuel ratio sensor output voltage is higher than 3.4
V
Result
RESULT
PROCEED TO
Abnormal
A
Normal
B
HINT:
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1603,P160...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст