Toyota Tundra (2015 year). Manual — part 197
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000012ZC01YX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: BRAKE: FRONT BRAKE: REMOVAL; 2015 MY Tundra [08/2014 - ]
REMOVAL
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. REMOVE FRONT WHEEL
2. REMOVE FRONT DISC BRAKE PAD KIT
(a) Remove the pin hold clip.
NOTICE:
The pin hold clip can be used again if it has sufficient rebound;
no deformation or wear; and has had all rust, dirt and foreign
matter cleaned off.
(b) Remove the hole pins.
(c) Remove the front disc brake anti-rattle spring.
NOTICE:
The anti-rattle spring can be used again if it has sufficient
rebound; no deformation, cracks or wear; and has had all rust,
dirt and foreign matter cleaned off.
(d) Remove the 2 pads from the disc brake caliper.
(e) Remove the No. 1 and No. 2 anti-squeal shims from each pad.
3. DRAIN BRAKE FLUID
NOTICE:
Wash brake fluid off immediately if it is spilled on any painted surface.
BRAKE: FRONT BRAKE: REMOVAL; 2015 MY Tundra [08/2014 - ]
4. DISCONNECT NO. 7 FRONT BRAKE TUBE
(a) Using a union nut wrench, disconnect the front brake tube from
the disc brake caliper.
5. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY LH
(a) Remove the 2 bolts and disc brake caliper from the knuckle.
6. REMOVE FRONT DISC
(a) Put matchmarks on the front disc and axle hub if planning to
reuse the disc.
(b) Remove the front disc.
BRAKE: FRONT BRAKE: REMOVAL; 2015 MY Tundra [08/2014 - ]
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000012ZD01TX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: BRAKE: FRONT BRAKE: DISASSEMBLY; 2015 MY Tundra [08/2014 - ]
DISASSEMBLY
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. REMOVE CYLINDER BOOT
(a) Using a screwdriver, remove the 4 set rings and 4 cylinder boots
from the disc brake caliper.
HINT:
Tape the screwdriver tip before use.
2. REMOVE FRONT DISC BRAKE PISTON
out.
(c) Using an air gun, gradually apply compressed air and remove the 2 disc brake pistons from the cylinder.
CAUTION:
(e) Temporarily install the 2 disc brake pistons that were removed. Then install the disc brake pad to the side
in which the 2 disc brake pistons were temporarily installed.
(g) Using an air gun, gradually apply compressed air and remove the 2 disc brake pistons from the other side
3. REMOVE PISTON SEAL
BRAKE: FRONT BRAKE: DISASSEMBLY; 2015 MY Tundra [08/2014 ...
(a) Using a screwdriver, remove the 4 piston seals from the disc
brake caliper.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Do not damage the inner cylinder or cylinder groove.
4. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP
5. REMOVE FRONT DISC BRAKE BLEEDER PLUG
BRAKE: FRONT BRAKE: DISASSEMBLY; 2015 MY Tundra [08/2014 ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст