Toyota Tundra (2015 year). Manual — part 1843
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQE03FX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSPECTION; 2015 MY
Tundra [08/2014 - ]
INSPECTION
1. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Partially soak the sensor in water and warm up the water.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
1 - 2
Approx. 20°C (68°F)
2.32 k to 2.59 kΩ
1 - 2
Approx. 80°C (176°F)
0.310 k to 0.326 kΩ
If the result is not as specified, replace the sensor.
NOTICE:
When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.
HINT:
If the result is as specified, do not replace the engine coolant temperature sensor.
3UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEM...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002PQD03RX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSTALLATION; 2015
MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor
.
1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
HINT:
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor
.
(a) Install a new gasket to the sensor.
(b) Using a 19 mm ball joint lock nut wrench, install the sensor.
Torque:
without 19 mm ball joint lock nut wrench -
20 N·m {200 kgf·cm, 14ft·lbf}
with 19 mm ball joint lock nut wrench -
10 N·m {104 kgf·cm, 8ft·lbf}
(c) Connect the sensor connector.
2. ADD ENGINE COOLANT
3. INSPECT FOR COOLANT LEAK
4. INSTALL V-BANK COVER SUB-ASSEMBLY
5. INSTALL NO. 1 ENGINE UNDER COVER
3UR-FE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEM...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQX028X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON-VEHICLE INSPECTION; 2015 MY Tundra
[08/2014 - ]
ON-VEHICLE INSPECTION
1. REMOVE FUEL PUMP RELAY (F/PMP)
(a) Remove the fuel pump relay from the engine room relay block.
2. INSPECT FUEL PUMP RELAY
(a) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 5
When no battery voltage is
applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is
applied to terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
3. INSTALL FUEL PUMP RELAY
3UR-FE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON-V...
Last Modified: 9-16-2014
6.6 K
Doc ID: RM0000031YK024X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENSOR: COMPONENTS; 2015 MY Tundra
[08/2014 - ]
COMPONENTS
ILLUSTRATION
ILLUSTRATION
3UR-FE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENSO...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст