Toyota Tundra (2015 year). Manual — part 599
OK
NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY
ASSEMBLY
11.
INSPECT TORQUE CONVERTER ASSEMBLY
(a) Check the torque converter assembly
.
OK:
The torque converter operates normally.
NG
REPLACE TORQUE CONVERTER ASSEMBLY
OK
REPAIR OR REPLACE AUTOMATIC TRANSMISSION
ASSEMBLY
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W860EMX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0973,P0974; Shift Solenoid
"A" Control Circuit Low (Shift Solenoid Valve S1); 2015 MY Tundra [08/2014 - ]
DTC
P0973
Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)
DTC
P0974
Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)
DESCRIPTION
solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated
safely. Also, the ECM stops sending the current to the open or short circuited solenoid
.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0973
ECM detects short in solenoid valve S1 circuit 2 times when
solenoid valve S1 is operated (1 trip detection logic)
Short in shift solenoid
valve S1 circuit
Shift solenoid valve S1
ECM
P0974
ECM detects open in solenoid valve S1 circuit 2 times when
solenoid valve S1 is not operated (1 trip detection logic)
Open in shift solenoid
valve S1 circuit
Shift solenoid valve S1
ECM
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit
in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When
the shift solenoid valve S1 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift
solenoid valve S1 circuit.
When the shift solenoid valve S1 is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open
in the shift solenoid valve S1 circuit
.
MONITOR STRATEGY
Related DTCs
P0973: Shift solenoid valve S1/Range check (Low resistance)
P0974: Shift solenoid valve S1/Range check (High resistance)
Required sensors/Components
Shift solenoid valve S1
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Duration
0.128 seconds or more
MIL operation
Immediately
TYPICAL ENABLING CONDITIONS
All
The monitor will run whenever the following DTCs are not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
P0973: Range Check (Low Resistance)
Command to shift solenoid valve S1
ON
P0974: Range Check (High Resistance)
Command to shift solenoid valve S1
OFF
TYPICAL MALFUNCTION THRESHOLDS
P0973: Range Check (Low Resistance)
Shift solenoid valve S1 resistance
8 Ω or less
P0974: Range check (High Resistance)
Shift solenoid valve S1 resistance
100 kΩ or more
COMPONENT OPERATING RANGE
Shift solenoid valve S1 resistance
11 to 15 Ω at 20°C (68°F)
WIRING DIAGRAM
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
HINT:
The shift solenoid valve S1 is turned ON/OFF normally when the shift lever is on D:
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve S1
OFF
ON
ON
ON
ON
ON
PROCEDURE
1.
INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
(a) Disconnect the D63 No. 1 transmission wire connector.
(b) Measure the resistance according to the value(s) in the table below.
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст