Toyota Tundra (2015 year). Manual — part 1463
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQE03EX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSPECTION; 2015
MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Partially immerse the sensor in water and warm up the water.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
1 - 2
Approx. 20°C (68°F)
2.32 k to 2.59 kΩ
1 - 2
Approx. 80°C (176°F)
0.310 k to 0.326 kΩ
If the result is not as specified, replace the sensor.
NOTICE:
When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.
HINT:
If the result is as specified, do not replace the engine coolant temperature sensor.
3UR-FBE ENGINE CONTROL SYSTEM: ENGINE COOLANT TE...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002PQD03QX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: ENGINE COOLANT TEMPERATURE SENSOR: INSTALLATION; 2015
MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL ENGINE COOLANT TEMPERATURE
SENSOR
(a) Install a new gasket to the sensor.
(b) Using a 19 mm ball joint lock nut wrench, install the sensor.
Torque:
without 19 mm ball joint lock nut wrench -
20 N·m {200 kgf·cm, 14ft·lbf}
with 19 mm ball joint lock nut wrench -
10 N·m {104 kgf·cm, 8ft·lbf}
(c) Connect the sensor connector.
2. ADD ENGINE COOLANT
3. INSPECT FOR COOLANT LEAK
4. INSTALL V-BANK COVER SUB-ASSEMBLY
5. INSTALL NO. 1 ENGINE UNDER COVER
3UR-FBE ENGINE CONTROL SYSTEM: ENGINE COOLANT TE...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000003QR7007X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: FUEL PRESSURE CONTROL VALVE RELAY: ON-VEHICLE
INSPECTION; 2015 MY Tundra [08/2014 - ]
ON-VEHICLE INSPECTION
1. REMOVE FUEL PRESSURE CONTROL VALVE RELAY (F/PMP VSV)
(a) Remove the fuel pressure control valve relay from the engine room relay block.
2. INSPECT FUEL PRESSURE CONTROL VALVE RELAY
(a) Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 5
When no battery voltage is
applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is
applied to terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
3. INSTALL FUEL PRESSURE CONTROL VALVE RELAY
3UR-FBE ENGINE CONTROL SYSTEM: FUEL PRESSURE CONTR...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002PQX026X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON-VEHICLE INSPECTION; 2015 MY Tundra
[08/2014 - ]
ON-VEHICLE INSPECTION
1. REMOVE FUEL PUMP RELAY (F/PMP)
(a) Remove the fuel pump relay from the engine room relay block.
2. INSPECT FUEL PUMP RELAY
(a) Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 5
When no battery voltage is
applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is
applied to terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
3. INSTALL FUEL PUMP RELAY
3UR-FBE ENGINE CONTROL SYSTEM: FUEL PUMP RELAY: ON...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст