Toyota Tundra (2015 year). Manual — part 321
the engine speed reaches the stall speed.
(11) In the same manner, perform the test with the shift lever in R.
Specified Line Pressure
CONDITION
D POSITION
R POSITION
Stall speed
1280 to 1460 kPa
(13.1 to 14.9 kgf/cm
2
, 186 to 212 psi)
1180 to 1400 kPa
(12.0 to 14.3 kgf/cm
2
, 171 to 203 psi)
Evaluation
PROBLEM
POSSIBLE CAUSE
Measured values at both positions are higher than specified
pressure
Shift solenoid valve SLT
defective
Regulator valve defective
Measured values at both positions are lower than specified
pressure
Shift solenoid valve SLT
defective
Regulator valve defective
Oil pump defective
Pressure is low in D only
D position circuit fluid leak
Clutch No. 1 (C1) defective
Pressure is low in R only
R position circuit fluid leak
Clutch No. 3 (C3) defective
Brake No. 4 (B4) defective
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000000W7C0XUX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: MANUAL SHIFTING TEST;
2015 MY Tundra [08/2014 - ]
MANUAL SHIFTING TEST
1. MANUAL SHIFTING TEST
HINT:
Through this test, it can be determined whether the trouble occurs in an electrical circuit or if it is a
mechanical problem in the transmission.
If any abnormalities are found in the following test, the problem is in the transmission itself.
It is possible to deactivate the electrical shift control by
disconnecting the transmission wire. The gear positions can then
be changed mechanically with the shift lever.
(b) Drive the vehicle with the transmission wire disconnected. Move the shift lever to each position to check
whether the gear position changes as shown in the table below.
SHIFT LEVER POSITION
GEAR POSITION
P
P
R
R
D
4th
.
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000000W7F0Q2X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: INITIALIZATION; 2015 MY
Tundra [08/2014 - ]
INITIALIZATION
1. RESET MEMORY
NOTICE:
The reset procedure is as follows.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.
NOTICE:
After performing Reset Memory, be sure to perform the Road Test
described earlier.
HINT:
The ECM learns through the Road Test.
2. ATF THERMAL DEGRADATION ESTIMATE RESET
NOTICE:
HINT:
If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate",
similar operation.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
NOTICE:
Do not start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Utility / ATF Thermal Degradation Estimate
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Reset.
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст