Toyota Tundra (2015 year). Manual — part 1960
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000002Z1T0FFX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060E; Internal Control Module Throttle Position
Performance; 2015 MY Tundra [08/2014 - ]
DTC
P060E
Internal Control Module Throttle Position Performance
DESCRIPTION
signals and control signals are deviated, a DTC is output.
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
P060E
When either condition below is met:
ECM main CPU error
ECM sub CPU error
ECM
MONITOR STRATEGY
Related DTCs
None
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Duration
1 second: Case 1
13 times: Case 2
MIL operation
Immediate
TYPICAL ENABLING CONDITIONS
Case 1
Monitor runs whenever following DTCs not present
None
Case 2
Monitor runs whenever following DTCs not present
None
DMA communication error
Not detected
TYPICAL MALFUNCTION THRESHOLDS
Case 1
Case 2
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060E; Interna...
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
1.
Turn the ignition switch to ON and turn the Techstream on.
2.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
3.
Turn the ignition switch off and wait for at least 30 seconds.
4.
Turn the ignition switch to ON and turn the Techstream on.
5.
Wait 16 seconds or more [A].
6.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
7.
Read the Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
8.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
9.
Input the DTC: P060E.
10.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
11.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060E; Interna...
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and
check for permanent DTCs
.
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
12.
INSPECTION PROCEDURE
NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the
negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the
negative (-) battery terminal notices before proceeding with work
.
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition
information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame
data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if
the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
CHECK DTC
(a) Clear DTC
.
(b) Turn the ignition switch off.
(c) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the ignition switch to ON.
(f) Check DTC.
OK:
P060E is not present.
NG
REPLACE ECM
OK
CHECK FOR INTERMITTENT PROBLEMS
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P060E; Interna...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000TA01H5X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0617; Starter Relay Circuit High; 2015 MY Tundra
[08/2014 - ]
DTC
P0617
Starter Relay Circuit High
DESCRIPTION
malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage
10.5 V or more applied to ECM for 20 seconds (1 trip detection
logic)
(a) Vehicle speed 20 km/h (12.4 mph) or more
(b) Engine speed 1000 rpm or more
(c) STA signal ON
Park / Neutral
Position (PNP)
switch
Starter relay circuit
Ignition switch
ECM
MONITOR STRATEGY
Related DTCs
P0617: Starter signal
Required Sensors/Components (Main)
ST relay, PNP switch and Ignition switch
Required Sensors/Components (Related)
Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor
Duration
20 seconds
MIL Operation
Immediate
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or more
Vehicle speed
20 km/h (12.4 mph) or more
Engine speed
1000 rpm or more
TYPICAL MALFUNCTION THRESHOLDS
Starter signal
ON
CONFIRMATION DRIVING PATTERN
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0617; Starter...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст