Toyota Tundra (2015 year). Manual — part 2153
29. REMOVE UPPER CAB REAR PILLAR PLATE RH
HINT:
Use the same procedures described for the LH side.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for C...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM00000345V00DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for CrewMax): INSPECTION; 2015 MY Tundra
[08/2014 - ]
INSPECTION
1. INSPECT BACK DOOR POWER WINDOW REGULATOR
MOTOR
voltage is applied to terminals 1 and 2 as follows.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
If the result is not as specified, replace the motor.
2. INSPECT NO. 1 BACK POWER WINDOW RELAY (except 3UR-FBE)
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for C...
3. INSPECT NO. 2 BACK POWER WINDOW RELAY
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
4. INSPECT NO. 3 BACK POWER WINDOW RELAY (for 3UR-FBE)
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for C...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM00000304G00PX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for CrewMax): INSTALLATION; 2015 MY Tundra
[08/2014 - ]
INSTALLATION
HINT:
A bolt without a torque specification is shown in the standard bolt chart
.
1. INSTALL UPPER CAB REAR PILLAR PLATE LH
(a) Align the positioning hole with the claw, and install the upper
plate with the 4 bolts as shown in the illustration.
2. INSTALL UPPER CAB REAR PILLAR PLATE RH
HINT:
Use the same procedures described for the LH side.
3. INSTALL BACK WINDOW OUTSIDE MOULDING
(a) Install the outside moulding with the 3 clips.
(b) Using an air riveter or hand riveter with a nose piece, install the back window outside moulding with 16
new rivets.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for C...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст