Toyota Camry (2019 year). Instruction — part 30

465

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Remove the air conditioning fil-
ter from the filter case and
replace it with a new one.

The “

UP” marks shown on the fil-

ter and the filter case should be
pointing up.

■

Checking interval
Inspect and replace the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, early replacement
may be required. (For scheduled maintenance information, please refer to the
“Schedule maintenance guide” or “Owner’s Manual Supplement”.)

■

If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.

■

Air conditioning filter with deodorizing function
When fragrances are placed in your vehicle, the deodorizing effect may
become significantly weakened in a short period.
When an air conditioning odor comes out continuously, replace the air condi-
tioning filter.

5

NOTICE

■

When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the
system.

■

To prevent damage to the filter cover

When moving the filter cover in the direc-
tion of arrow to release the fitting, pay
attention not to apply excessive force to
the claws. Otherwise, the claws may be
damaged.

466

6-3. Do-it-yourself maintenance

CAMRY_U

● Flathead screwdriver
● Small flathead screwdriver
● Lithium battery CR2032



Vehicles without a smart key system

Remove the key cover.

To prevent damage to the key,
cover the tip of the flathead screw-
driver with a rag.

Remove the battery cover.

If the battery cover is difficult to
remove, lift the edge to remove it.

Remove the depleted battery
using a small flathead screw-
driver.

Insert a new battery with the “+”
terminal facing up.

Wireless remote control/electronic key

battery

Replace the battery with a new one if it is depleted.

You will need the following items:

Replacing the battery

1

2

3

467

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Install the battery cover with the
tab facing up.

Push the entire edge of the battery
cover into the key.

Install the key cover.

Align the key cover with the key
and then press it straight into the
key.
Make sure that the key cover is
securely installed without any gaps
between it and the key.

Operate the

or

switch and check that the doors can

be locked/unlocked.

4

5

6

468

6-3. Do-it-yourself maintenance

CAMRY_U



Vehicles with a smart key system

Release the lock and remove
the mechanical key.

Remove the key cover.

To prevent damage to the key,
cover the tip of the flathead screw-
driver with a rag.

Remove the depleted battery
using a small flathead screw-
driver.

When removing the cover, the
electronic key module may stick to
the cover and the battery may not
be visible. In this case, remove the
electronic key module in order to
remove the battery.
Insert a new battery with the “+” terminal facing up.

When installing the key cover and mechanical key, install by con-
ducting

and

with the directions reversed.

Operate the

or

switch and check that the doors can

be locked/unlocked.

1

2

3

4

2

1

5

469

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

■

When replacing the key battery
Be careful not to lose the battery or any other small parts.

■

Use a CR2032 lithium battery

●

Batteries can be purchased at your Toyota dealer, local electrical appliance
shops or camera stores.

●

Replace only with the same or equivalent type recommended by the manu-
facturer.

●

Dispose of used batteries according to local laws.

■

If the key battery is depleted
The following symptoms may occur:

●

The smart key system (if equipped) and wireless remote control will not
function properly.

●

The operational range will be reduced.

WARNING

■

Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking.
Keep away from children. Failure to do so could result in death or serious
injury.

NOTICE

■

For normal operation after replacing the battery
Observe the following precautions to prevent accidents:

●

Always work with dry hands.
Moisture may cause the battery to rust.

●

Do not touch or move any other component inside the remote control.

●

Do not bend either of the battery terminals.

■

When removing the battery cover (vehicles without a smart key sys-
tem)
Do not forcibly remove the battery cover, otherwise it may be damaged.
If the battery cover is difficult to remove, lift the edge to remove it.

470

6-3. Do-it-yourself maintenance

CAMRY_U

Turn the engine switch off.
Open the fuse box cover.

Checking and replacing fuses

If any of the electrical components do not operate, a fuse may
have blown. If this happens, check and replace the fuses as nec-
essary.

1

2



Engine compartment (type A)



Engine compartment (type B)
(if equipped)

Push the tabs in and lift the lid off.

Push the tabs in and lift the lid
off.



Under the driver’s side instru-
ment panel

Remove the lid.

Make sure to push the claw when
removing/installing the lid.

471

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Remove the fuse with the pull-
out tool.

Only type A fuses can be removed
using the pullout tool.

Check if the fuse is blown.

Normal fuse
Blown fuse

Replace the blown fuse with a new fuse of an appropriate amperage rat-
ing. The amperage rating can be found on the fuse box lid.

3

4



Type A



Type B



Type C

1

2

472

6-3. Do-it-yourself maintenance

CAMRY_U

■

After a fuse is replaced

●

If the lights do not turn on even after the fuse has been replaced, a bulb may
need replacement. (

P. 473)

●

If the replaced fuse blows again, have the vehicle inspected by your Toyota
dealer.

■

If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.

WARNING

■

To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage to the vehicle, and possibly a fire or
injury.

●

Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.

●

Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.

●

Do not modify the fuses or fuse boxes.

NOTICE

■

Before replacing fuses
Have the cause of electrical overload determined and repaired by your
Toyota dealer as soon as possible.

473

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Check the wattage of the light bulb to be replaced. (

P. 550)

Light bulbs

You may replace the following bulbs yourself. The difficulty level
of replacement varies depending on the bulb. If necessary bulb
replacement seems difficult to perform, contact your Toyota
dealer.
For more information about replacing other light bulbs, contact
your Toyota dealer.

Preparing for light bulb replacement

Bulb locations



Front



Rear

Front turn signal/parking lights
(bulb type)
Front side marker lights (bulb
type)

Back-up lights (bulb type)
Rear turn signal lights (bulb
type)
Rear side marker lights (bulb
type)

1

2

1

2

3

474

6-3. Do-it-yourself maintenance

CAMRY_U

■

Front turn signal/parking lights (bulb type)

Turn the bulb base counter-
clockwise.

Remove the light bulb.

Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.

Replacing light bulbs

1

2

3

475

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

■

Front side marker lights (bulb type)

To ensure enough space to
perform work, turn the steer-
ing wheel to move the front
wheel away from the light
bulb to be replaced.

Turn the steering wheel to the
left when replacing the right side
light bulb, and turn the steering
wheel to the right when replac-
ing the left side light bulb.

Remove the fender liner
clips.

To protect the front bumper
from being damaged, apply
protective tape around the
clip as shown in the illustra-
tion.

Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.

1

2

3

476

6-3. Do-it-yourself maintenance

CAMRY_U

Insert a small flathead screw-
driver between the front
bumper and fender liner at
the position marked with a
“

” and then separate the

front bumper from the fender
liner.

To separate the front bumper
from the fender liner, pry up the
fender liner while pulling the
front bumper outward as shown
in the illustration.

Pull back the fender liner and
turn the bulb base counter-
clockwise.

Remove the light bulb.

Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.

4

5

6

7

477

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Return the fender liner to its
original position, and install
the clips.

Make sure that the fender liner
is correctly positioned on the
inner side of the front bumper.

To Install the fender liner to
the front bumper, engage the
clip to the front bumper.

Remove the protective tape.

8

9

10

478

6-3. Do-it-yourself maintenance

CAMRY_U

■

Back-up lights (bulb type)

Open the trunk lid and remove the clips.

Type A: To prevent damaging the vehicle, wrap the tip of the flathead
screwdriver with tape.

Partly remove the trunk lid
cover.

Disconnect the connector
while depressing the lock
release. (When replacing
right side bulb only.)

Turn the bulb base counter-
clockwise.

1



Type A



Type B

2

3

4

479

6-3. Do-it-yourself maintenance

CAMRY_U

6

Mainten

ance an

d ca

re

Remove the light bulb.

Install a new light bulb and
then install the bulb base to
the light unit by inserting it
and turning it clockwise.

Connect

the

connector.

(When replacing right side
bulb only.)

Reinstall the trunk lid cover with the clips.

5

6

7

8



Type A



Type B

480

6-3. Do-it-yourself maintenance

CAMRY_U

■

Rear turn signal lights (bulb type) and rear side marker lights
(bulb type)

Open the trunk and apply
protective tape to the vehicle
body around the light unit.

Use masking tape, etc. Do not
use duct tape, as it may leave
residue or damage the paint
when removed.

Remove the cover.

Insert a flathead screw-
driver between the cover
and the light unit and pry
up the cover in several
positions as shown in the
illustration to disengage
the claws (indicated by a
dotted line).
Pull the cover toward the
rear of the vehicle to dis-
engage the claws (indi-
cated by a dotted line) and
remove the cover.

To prevent scratching the vehi-
cle, wrap the tip of the flathead
screwdriver with a cloth, etc.

Remove the 2 bolts.

1

2

1

2

3