Toyota Prius Prime (2021 year). Manual in english — part 3
150
PRIUS PRIME_OM_OM47D71U_(U)
To prevent electrical shock, be sure to remove by following the proce-
dures below.
Vehicles with smart lid & con-
nector locking system:
When the charging connector is
locked, carry an electronic key
and press the charging connec-
tor lock switch.
The
charging
connector
is
unlocked by the smart lid & con-
nector locking system.
Carrying an electronic key and moving near the charging inlet will cause
the charging inlet light to illuminate.
Pull the charging connector
towards you while pressing the
latch release button.
If the latch release button is
pressed during charging (while the
charging indicator is on), charging
will be interrupted.
Attach the charging connector
cap.
Attach the charging inlet cap
and close the charging port lid.
After charging
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
151
2
Plug-
Remove the plug from the out-
let when the charging equip-
ment will not be used for a
prolonged period of time.
Hold the body of the plug when
removing.
Make sure to put the cable away
immediately after disconnecting.
(
When leaving the plug inserted, inspect the plug and connector once a
month to check if dirt or dust has accumulated.
■
Charging time
■
Safety function
If the latch release button is pressed, charging will not begin even if the
charging cable is connected.
Also, charging will be stopped if the latch release button is pressed and held
for several seconds during charging. When restarting charging, reinsert the
charging connector after pulling it out, and check that the charging indicator
illuminates.
■
When the outside temperature is low or high
The level shown on the remaining charge display (
P. 231) may drop slightly
when the power switch is turned to ON mode, even if charging has been com-
pleted and the hybrid battery (traction battery) is fully charged. However, this
does not indicate a malfunction.
■
Charging time may increase
■
While charging
When the power switch is turned to ON mode and the energy monitor dis-
plays, the charging connector is displayed on the energy monitor and the flow
of electricity during charging is displayed (
P. 223). Also, when the charging
connector is locked,
is displayed.
*
*
: Vehicles with smart lid & connector locking system only
■
If the charging cable cannot be unlocked
5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
152
PRIUS PRIME_OM_OM47D71U_(U)
■
When removing the charging connector
■
Push lifter (vehicles with smart lid & connector locking system)
Press the latch release button, check that
the lever raises up, and then pull the
charging connector towards you.
Vehicles with smart lid & connector lock-
ing system: If the lever does not raise up
even after the latch release button is
pressed, the charging connector is
locked. If this occurs, carry an electronic
key and press the charging connector
lock switch to unlock the charging con-
nector.
When the charging port lid is open, make
sure not to touch the push lifter. If it is
touched accidentally, the charging port lid
or connector lock may operate.
If they are accidentally operated, carry an
electronic key or unlock the doors, and
then press the charging connector lock
switch to unlock.
Push lifter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
153
2
Plug-
WARNING
■
When charging
Observe the following precautions.
Failure to do so may cause an unexpected accident, resulting in death or
serious injury.
●
Connect to a power source suitable for charging. (
●
Before charging, check that the charging inlet does not have deformations,
damage, corrosion, dust or other foreign materials such as snow or ice
adhering to it. If anything is adhering to the inlet, be sure to completely
remove the material before connecting the charging connector.
●
Do not let the terminals of the charging inlet get wet.
●
Make sure that the charging cable, plug and socket are free of foreign mat-
ter and not deformed or damaged.
●
Only use outlets where the plug can be securely inserted.
●
Do not charge if the charging cable is coiled or bundled.
●
Wrapping 120 V charging cable while in-use is not recommended because
cable may overheat. Failure to rewrap charging cable when not in-use
could result in strangulation or tripping hazard.
●
Do not touch the terminals of the charging connector and charging inlet
with a sharp metal objects (needles etc.) or hands, or short them with for-
eign objects.
●
When charging outdoors, make sure to connect to a weatherproof outlet
for outdoor use.
●
If any heat, smoke, odors, noise or other abnormalities are noticed during
charging, stop charging immediately.
●
Do not insert the plug if the outlet is submerged in water or snow.
●
When charging during rain or snow, do not pull out or insert the plug with
wet hands. Also, do not get the electrical socket and plug wet.
●
Do not charge the vehicle during a lightning storm.
●
Do not let the wheels on the charging cable, plug, charging connector and
CCID (Charging Circuit Interrupting Device).
●
Firmly insert the plug into the outlet.
●
Do not use an extension cord and converting adaptor.
●
After connecting the charging cable, confirm that it is not wound around
anything.
●
If the power indicator light does not illuminate after plugging the charging
cable into the socket-outlet, unplug it immediately.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
154
PRIUS PRIME_OM_OM47D71U_(U)
WARNING
■
If the error warning indicator on the CCID (Charging Circuit Interrupt-
ing Device) illuminates or flashes during charging
There may be an electrical leakage in the power source path, or there may
be a malfunction in the charging cable or CCID (Charging Circuit Interrupt-
ing Device). Refer to P. 118 and follow the correction procedure. If the error
warning indicator does not turn off even after performing the correction pro-
cedure, immediately stop charging, remove the charging cable and contact
your Toyota dealer. Continuing to charge the vehicle in that condition may
lead to unforeseen accidents or serious injury.
■
After charging
Remove the plug if it will not be used for a long time.
Dirt and dust may accumulate plug or outlet, which could cause a malfunc-
tion or fire, possibly leading to death or serious injury.
■
Onboard traction battery charger
The onboard traction battery charger is located under the rear seats. Make
sure to observe the following precautions regarding the onboard traction
battery charger. Failure to observe these precautions may result in death or
serious injury such as burns and electric shocks.
●
The onboard traction battery charger is hot during charging. Do not touch
the onboard traction battery charger, as doing so may result in burns.
●
Do not disassemble, repair or modify the onboard traction battery charger.
When the onboard traction battery charger needs to be repaired, consult
your Toyota dealer.
■
Charging inlet
Do not disassemble, repair or modify the charging inlet. It may lead to
unforeseen accidents or serious injury. When the charging inlet needs to be
repaired, consult your Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
155
2
Plug-
NOTICE
■
When use the charging cable and related parts
To prevent damage to the charging cable and related parts, observe the fol-
lowing precautions.
●
When interrupting or canceling charging, remove the charging connector
before removing the plug.
●
Vehicles with smart lid & connector locking system: When removing the
charging cable, check that the charging connector is unlocked.
●
Do not forcefully pull the connector cap and charging inlet cap.
●
Do not apply a vibration to the charging connector while charging.
Charging may be stopped.
●
Do not insert anything but the charging connector.
●
When inserting the plug into or removing the plug from the outlet, make
sure to hold the body of the plug.
●
Do not damage the charging inlet cap with a sharp object.
●
Do not forcefully pull the charging cable that is caught or entangled.
If the cable is entangled, disentangle it before using.
●
When charging from the external device, use the charging cable equipped
with the vehicle.
■
When charging
Do not insert the plug into the charging inlet.
The charging inlet may be damaged.
■
After charging
●
Store the charging cable out of reach from infants and children.
●
After disconnecting the charging connector from the charging inlet, make
sure to put on the charging inlet cap and close the charging port lid.
If the charging inlet cap is not put on, water or foreign objects may enter
the charging inlet, which could lead to vehicle damage.
●
After removing the plug from the outlet, keep it in a safe place free from
moisture and dust.
The charging cable or plug may be damaged if the cable is stepped on or
ridden over by the vehicle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
156
PRIUS PRIME_OM_OM47D71U_(U)
NOTICE
■
Using private power generator
Do not use private power generators as a power source for charging.
Doing so may make charging unstable, the voltage may be insufficient, and
the error warning indicator on the CCID (Charging Circuit Interrupting
Device) of the charging cable may flash.
■
Charging station
Due to the environment in which the power equipment is located, charging
may be unstable due to noise, the voltage may be insufficient, and the error
warning indicator on the CCID (Charging Circuit Interrupting Device) of the
charging cable may flash.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
157
PRIUS PRIME_OM_OM47D71U_(U)
2
Plug-
Using the charging schedule function
When registering the charge schedule, the following settings can be
changed.
■
Select the charging mode
One of the two following charging modes can be selected.
*
1
: Charging schedule function is performed in accordance with the clock in
the instrument cluster. Before registering the charge schedule, check the
clock settings to the proper time.
*
2
: There might be a slight error in the timing when charging starts due to the
state of the hybrid battery (traction battery).
■
Repeated setting
The periodic charging schedule can be set by selecting your
desired day of the week.
■
Air conditioning-linked setting (“Climate Prep”)
When the charging mode is set to “Departure”, the vehicle air condi-
tioning system (
P. 512, 524) can be set to automatically operate*
according to the set time.
By adjusting the cabin temperature in advance, passengers can enjoy a
pleasant interior immediately after entering the vehicle.
*
: Operation starts approximately 10 minutes before the set departure time.
Charging can be carried out at the desired time by registering
the charge schedule. Also, it is possible to set the charging
schedule to one’s preferences, such as having charging com-
plete by a certain departure time or be carried out at the same
time on certain days.
Settings of the charging schedule function
Charging mode
Operation description
“Start”
Starts charging at the set time
*
1
and finishes
charging when fully charged.
*
2
“Departure”
Starts charging to finish at the set time.
When this setting is selected, the air conditioning-
linked function can be used.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
158
PRIUS PRIME_OM_OM47D71U_(U)
■
Turning “Charge Now” on and off
If even one charge schedule is registered, charging does not start
until the set time, even if the charging cable is connected to the
vehicle. To start charging without changing the charge schedule
setting, turn “Charge Now” on to temporarily cancel the charge
schedule and enable charging after connecting the charging cable.
■
Changing “Next Charging Event”
*
1
It is possible to temporarily set the time of the next scheduled
charge without changing the registered repeated setting.
*
2
*
1
: The “Next Charging Event” refers to the closest charge schedule from the
current time among the registered charge schedules. Charging schedule is
performed based on the “Next Charging Event”.
*
2
: When “Next Charging Event” is changed, the current charge schedule will
be temporarily ignored and charging will not be carried out until the time
specified by “Next Charging Event”. (For example, when “Next Charging
Event” is set for 2 days later, even if items are registered on the charge
schedule, charging will not be carried out until the time specified by “Next
Charging Event”.)
The charge schedule can be reg-
istered on the multi-information
display or 11.6-inch display (if
equipped).
●
Multi-information display opera-
tion:
●
11.6-inch display operation (if
equipped):
Registering the charge schedule
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
159
2
Plug-
■
Charging schedule
●
The charge schedule cannot be set while driving.
●
A maximum of 15 charge schedules can be registered.
■
To make sure that the charging schedule function operates correctly
Check the following items.
●
Adjust the clock to the correct time (
●
The calendar is set to the correct date (
●
Check that the power switch is turned off
●
After registering the charge schedule, connect the charging cable
The charging start time is determined based on the charge schedule at the
time that the charging cable was connected.
●
After connecting the charging cable, check that the charging indicator
flashes (
●
Do not use an outlet that has a power cut off function (including a timer func-
tion)
Use an outlet that constantly supplies electricity. For outlets where the
power is cut off due to a timer function, etc., charging may not be carried
out according to plan if the power is cut off during the set time.
■
When the charging cable remains connected to the vehicle
Even if multiple consecutive charge schedules are registered, the next
charge will not be carried out according to the charging schedule until the
charging cable is removed and reconnected after charging completes. Also,
when the hybrid battery (traction battery) is fully charged, charging according
to the charging schedule will not be carried out.
■
“Climate Prep”
●
When the air conditioning-linked setting is turned on, the air conditioning
operates until the set departure time. Therefore, the air conditioning will con-
sume electricity and charging may not complete by the set departure time.
●
If the hybrid battery (traction battery) is fully charged, charging will not be
carried out, even if the charge schedule is set. However, if “Climate Prep” is
turned on, the air conditioning will operate only once when it nears the time
set in “Departure”. If this occurs, the air conditioning will consume electricity
and the remaining charge of the hybrid battery (traction battery) when
departing may be decreased.
●
When the doors are unlocked, the air conditioning system does not operate.
■
Smartphone-linked operation (vehicles with 11.6-inch display)
After applying to Entune App Suite, it is possible to use the smartphone appli-
cation to change charging schedule settings.
For details about Entune App Suite, refer to http://www.toyota.com/entune/.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
160
PRIUS PRIME_OM_OM47D71U_(U)
■
When charging schedules are ignored
When the following operations are performed while the charging schedule is
on standby, charging schedule is temporarily canceled and charging is
started.
●
When the Remote Air Conditioning System (
P. 535) is operated
●
When turning “Charge Now” on (
●
When an operation that temporarily cancels charging using the charging
schedule is performed (
■
Effects of outside temperature
When the charging mode is set to “Departure”, charging schedule may be
ignored due to the outside temperature and charging may start.
■
“Traction Battery Cooler” (
When charging is carried out using the charging schedule, the hybrid battery
(traction battery) cooling function may operate according to the temperature
of the hybrid battery (traction battery).
●
When the charging mode is set to “Start”, cooling starts at the set charging
start time.
●
When the charging mode is set to “Departure”, cooling starts approximately
30 minutes before the charging start time. However, if there is no time to fin-
ish charging by the charging schedule, the hybrid battery (traction battery)
cooling time may be shortened and “Traction Battery Cooler” may not oper-
ate.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
161
2
Plug-
When operating charging schedule, use the charging schedule switch
and meter control switches.
Charging schedule switch
Meter control switches
(
Multi-information display
■
Registering the charge schedule
Press the charging schedule switch.
The “Charge Schedule” screen will display on the multi-information dis-
play.
Press
or
of the
meter control switches to
select “Scheduled Events”,
and then press
.
The “Scheduled Events” screen
will display.
Press
or
of the
meter control switches to
select “+”, and then press
.
The “Edit Charging Event”
screen will display.
Setting operations on multi-information display
1
2
3
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
162
PRIUS PRIME_OM_OM47D71U_(U)
Press
or
of the
meter control switches to
select the charging mode/
time settings row, and then
press
.
The charging mode/time set-
tings screen will display.
The clock display (12-hour dis-
play/24-hour display) changes
according to the clock settings.
(
Press
or
of the
meter control switches to
select the item to change
with the cursor, and then
press
or
to change
the setting.
Set the desired charging mode
and charging start (or departure)
time.
When the charging mode is “Start”, this sets the charging start time.
When it is “Departure”, this sets the charging end time.
After changing the settings to the desired settings, press
to return to
the previous screen.
To activate the repeated set-
ting, press
or
of the
meter control switches to
select “Repeat”, and then
press
.
A screen where the repeated
day can be selected will display.
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
163
2
Plug-
Press
or
of the
meter control switches to
select the desired day to acti-
vate for the repeated setting,
and then press
.
Each time
is pressed, the
repeated
setting
switches
between on and off.
When set to on, the selected day is highlighted and the charging sched-
ule is repeated on that day. It is possible to set more than one day to on.
If no days are set to on, charging is only carried out once according to
the charging schedule for the next 24 hours.
After changing the settings to the desired settings, press
to return to
the previous screen.
When the charging mode is
set to “Departure”, set the
“Climate Prep” (
P. 157) to
on or off.
To turn the function on and oper-
ate the air conditioning, press
or
of the meter control
switches to select “Climate
Prep”, and then press
.
Each time
is pressed, the function switches between on and off.
After setting operations are
complete, press
.
A screen where the settings can
be saved will display.
Press
or
of the meter
control switches to select “Yes”,
and then press
to save the
settings.
If you wish to change the settings, select “No” and perform the setting
procedure from step again.
After setting operations are complete, when the charging cable is con-
nected to the vehicle, charging will be carried out according to the
charging schedule settings.
7
8
9
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
164
PRIUS PRIME_OM_OM47D71U_(U)
■
Changing the registered charge schedules
The registered charge schedules can be turned on, off, deleted or
modified.
Press the charging schedule switch.
The “Charge Schedule” screen will display on the multi-information dis-
play.
Press
or
of the
meter control switches to
select “Scheduled Events”,
and then press
.
The “Scheduled Events” screen
is displayed, which displays a
list of the registered charge
schedule.
Press
or
of the
meter control switches to
select the item to change,
and then press
.
The “Edit Charging Event”
screen will display.
Press
or
of the
meter control switches to
select the item to operate
and perform the necessary
operation.
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
165
2
Plug-
●
“ON/OFF”
Each time
of the meter control switch is pressed, the
selected charge schedule switches between “On” and “Off”.
When set to “Off”, a charging schedule is ignored and charging accord-
ing to the charging schedule is not carried out.
When
is pressed, setting is complete.
●
“Edit”
Change the desired settings as described starting from step
of the “Registering the charge schedule” procedure. (
Press
or
of the
meter control switches to
select “Yes”, and then press
to save the charging
schedule.
Press
to return to the previ-
ous screen.
When canceling any changes, select “No” and then press
.
●
“Delete”
Pressing
of the meter control switch displays a deletion con-
firmation screen.
Press
or
of the
meter control switches to
select “Yes”, and then press
to delete the selected
charge schedule.
Press
to return to the previ-
ous screen.
To cancel deletion, select “No” and then press
.
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
166
PRIUS PRIME_OM_OM47D71U_(U)
■
Setting “Charge Now” to “On”
The “Charge Now” setting can be changed by performing one of the
two following procedures.
Operation on “Charge Schedule” screen
Press the charging schedule switch.
The “Charge Schedule” screen will display on the multi-information dis-
play.
Press
or
of the
meter control switches to
select “Charge Now”, and
then press
.
Each time
is pressed,
“Charge Now” switches between
“On” and “Off”.
Operation on “Ending” screen
Turn the power switch off.
The “Ending” screen is displayed on the multi-information display.
(
While the “Ending” screen is
displayed, press
or
of the meter control switches
to display the “Next Event”
screen.
*
*
: When the power switch is turned
off, the “Charge Now” setting
screen may be displayed.
Press
to set “Charge Now” to “On”.
Each time
is pressed, “Charge Now” switches between “On” and
“Off”.
After setting operations are complete, charging starts when the
charging cable is connected. (
1
2
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
167
2
Plug-
■
Changing “Next Charging Event”
*
*
: When “Charge Now” is set to “On” etc., it is not possible to change the reg-
istered “Next Charging Event”.
Press the charging schedule switch.
The “Charge Schedule” screen will display on the multi-information dis-
play.
Press
or
of the
meter control switches to
select
“Next
Charging
Event”, and then press
.
The “Edit Next Charging Event”
screen will display.
Press
or
of the
meter control switches to
select the item to change,
and then press
.
Change the registered settings
in accordance with the following
table.
1
2
3
Setting
Operation
Charging Mode/Time
Operate
,
,
and
of the meter control
switches to set the charging mode (“Start” or
“Departure”) and charging start (or departure) time.
After changing the settings, press
to return the
previous screen.
“Day”
Operate
or
of the meter control switches to
select the day to carry out charging according to the
charging schedule.
After changing the setting, press
to return the
previous screen.
“Climate Prep”
This can be set when the charging mode is set to
“Departure”. Each time
is pressed, air condition-
ing-linked operation switches between “On” and
“Off”.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
168
PRIUS PRIME_OM_OM47D71U_(U)
After setting operations are
complete, press
.
A confirmation screen of chang-
ing “Next Charging Event” will
display.
Press
or
of the meter
control switches to select “Yes”,
and then press
to save the
charging schedule.
Press
to return to the previous screen.
When canceling the “Next Charging Event”, select “No” and then press
.
■
Charging schedule switch
●
The charging schedule switch functions regardless of the condition of the
power switch.
However, when the charging schedule switch is pressed while the power
switch is not turned to ON mode, if the meter control switches are not oper-
ated for a certain amount of time after the charging schedule setting screen
is displayed, the display automatically turns off.
●
The charging schedule switch cannot be used while driving.
■
When charging schedule setting operations are canceled
When the vehicle is in the following conditions, charging schedule setting
operations are canceled.
●
A message is displayed while performing a setting operation
●
The power switch is operated before the settings are confirmed
●
The vehicle starts off
●
A display with a higher priority than that of the charging schedule setting is
shown
■
Charging schedule
The “Charge Schedule” screen can be displayed and setting operations can
be performed from the “Vehicle Settings” setting on the multi-information dis-
play. (
■
“Next Charging Event”
After charging completes, the “Next Charging Event” displayed on the multi-
information display will not change until the charging cable is removed, even
after charging is performed according to the “Next Charging Event” schedule.
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
169
2
Plug-
■
To return to original setting after changing “Next Charging Event” set-
ting
Turning the setting of “Charge Now” on and then off can return the setting of
“Next Charging Event” to its original setting.
■
When “Next Charging Event” is changed while charging
●
When the charging mode is “Departure”, the current charging is interrupted
or continued depending on the remaining time until the charging is com-
pleted.
●
When the charging mode is “Start”, the current charging is interrupted, the
next charging will start at the set time.
■
When the power switch is turned off
*
2
: When the power switch is turned off, the “Next Charging Event” confirma-
tion screen may be displayed.
It is possible to check the next charge
schedule (“Next Charging Event”) by oper-
ating
or
of the meter control
switches while the power switch is turned
off and the “Ending” screen
*
1
(
P. 196) is
displayed.
*
2
*
1
: The “Ending” screen may not be dis-
played during charging.
WARNING
■
Cautions while performing the setting operation
When performing the setting operation while the hybrid system is operated,
ensure that the vehicle is parked in a place with adequate ventilation. In a
closed area such as a garage, exhaust gases including harmful carbon
monoxide (CO) may collect and enter the vehicle. This may lead to death or
a serious health hazard.
NOTICE
■
While performing the setting operation
When performing the setting operation while the hybrid system is stopped,
be careful that the 12-volt battery will not be discharged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
170
PRIUS PRIME_OM_OM47D71U_(U)
Setting operations related to the charging schedule are performed on
the “Charge Schedule” screen.
For details on how to operate the 11.6-inch display, refer to “NAVIGATION
SYSTEM OWNER’S MANUAL”.
■
Displaying the “Charge Schedule” screen
Press the “MENU” button to
display the menu screen.
Select “Info” and “Charge
Schedule”, in that order.
The “Charge Schedule” screen
will display.
Setting operations on the 11.6-inch display (if equipped)
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
171
2
Plug-
■
How to read the “Charge Schedule” screen
Charge schedules (calendar display)
Displays the week-long registered charge schedule in a list using icons.
“Add” button
Press to add a new item to the charge schedule. (
Charge schedules (list display)
A list of items on the registered charge schedule is displayed. If there are
more than 3 registered items, the list can be scrolled up and down to
change the displayed items.
“Edit” button
Press to change or delete registered items on the charge schedule.
(
Return button
Press to close the “Charge Schedule” screen.
Charge schedules (icon display)
When an item is registered on the charge schedule, an icon is displayed
on the calendar.
“Charge Now” button
Press to set “Charge Now” to on. (
1
2
3
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
172
PRIUS PRIME_OM_OM47D71U_(U)
“ON”/“OFF” button
The charge schedule switches between “ON” and “OFF” each time this
button is pressed. (
Scroll bar
When the number of registered charge schedules exceeds 3, the dis-
played contents can be changed by operating the button.
Main content displayed on the calendar:
*
1
: A row with a red line indicates the current time.
*
2
: While a registered setting is being changed, the icon of the related setting
is highlighted (except when the icon overlaps with another icon).
*
3
: When “Charge Now” (
P. 175) is set to on, the orange icon moves to the
position of the red line and changes to display “Charge Now”.
*
4
: The content of the charge schedule that corresponds to the “Next Charging
Event” is not displayed in the list.
■
Registering the charge schedule
Display the “Charge Schedule” screen. (
Press “Add”.
The settings screen will display on the bottom of the screen.
8
9
Display
Content
Red line
*
1
Current time
Orange icon
*
2, 3
Charge schedule for “Next Charging Event”
*
4
Green icon
*
2
The charging mode is set to “Departure”
Blue icon
*
2
The charging mode is set to “Start”
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
173
2
Plug-
Select the charging mode.
Press “Start” or “Departure” to turn the button (charging mode) on and
highlight the button.
Operate the time setting wheel to set the start (or departure)
time.
When the charging mode is “Start”, set the charging start time (start
time). When it is “Departure”, set the charging end time (departure
time).
Operate the each wheel up and down to display the desired time in the
center.
When activating the repeated settings, press the desired day but-
ton.
Each time the button is pressed, the repeated setting for the selected
day switches between on and off.
When turned on, the button is highlighted and the charging schedule is
repeated on that day. It is possible to turn more than one day on.
If no buttons are turned on, charging is only carried out once according
to the charging schedule for the next 24 hours.
When the charging mode is set to “Departure”, set the “Climate
Prep” (
P. 157) to on or off.
To operate the air conditioning, press the “Climate Prep” button to set
the function to “ON”.
Each time the button is pressed, the function switches between “ON”
and “OFF”.
After setting operations are complete, press “Save”.
The charge schedule is added to the list and an icon is added to the cal-
endar.
To cancel registration of the charging schedule, press
.
After setting operations are complete, when the power switch is turned
off and the charging cable is connected to the vehicle, charging is car-
ried out according to the charging schedule settings.
3
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
174
PRIUS PRIME_OM_OM47D71U_(U)
■
Switching charge schedules between “ON” and “OFF”
Display the “Charge Schedule” screen. (
From the items in the list displayed on the bottom of the screen,
press “ON” or “OFF” in the row of the charge schedule you wish
to change.
Setting “ON” or “OFF” is possible by sliding the bar to the left or right.
If the charge schedule you wish to change is not displayed on the bot-
tom of the screen, scroll the list up and down to display it.
Each time the button is pressed, the charge schedule switches between
“ON” and “OFF”.
■
Changing the registered charge schedules
Display the “Charge Schedule” screen. (
From the items displayed on the bottom of the screen, press
“Edit” in the row of the charge schedule you wish to change.
The settings screen will display on the bottom of the screen.
It is also possible to display the settings screen by pressing the icon of
the charge schedule you wish to change from those displayed on the
calendar.
1
2
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
175
2
Plug-
●
Changing registered items:
Change the desired settings as described in step
to step
of
the “Registering the charge schedule” procedure. (
When a setting is changed, its icon on the calendar also changes.
●
Deleting registered items:
Press “Delete”.
A deletion confirmation message will display.
Press “Yes” to delete the selected charge schedule.
To cancel deletion, press “No”.
When a charge schedule is deleted, its icon is also deleted from the cal-
endar.
■
Turning “Charge Now” on
The “Charge Now” setting can be changed by performing one of the
two following procedures.
Operations on “Charge Schedule” screen
Display the “Charge Schedule” screen. (
Press “Charge Now”.
Each time the button is pressed, “Charge Now” switches between on
and off and the indicator on the button turns on and off.
3
7
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
176
PRIUS PRIME_OM_OM47D71U_(U)
Operation on ending screen
Turn the power switch off.
The ending screen is displayed on the 11.6-inch display.
While the ending screen is
displayed, press “Charge
Now”.
Each time the button is pressed,
“Charge Now” switches between
on and off and the indicator on
the button turns on and off.
After setting operations are complete, charging starts when the
charging cable is connected. (
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
177
2
Plug-
■
Changing “Next Charging Event”
*
*
: When “Charge Now” is turned on etc., the registered “Next Charging
Event” cannot be changed.
Display the “Charge Schedule” screen. (
“Next Charging Event” is displayed on the “Charge Schedule” screen
with an orange icon.
To change “Next Charging Event”, press the orange
.
*
The settings screen will display on the bottom of the screen.
*
: Icons are displayed differently according to the type of charging mode.
(
Select the desired charging mode.
Press “Start” or “Departure” to turn the button (charging mode) on and
highlight the button.
Operate the day setting wheel and time setting wheels up and
down to set the charging day and start (or departure) time.
Operate each wheel up and down to display the desired date and time
in the center.
When the charging mode is “Start”, set the charging start time. When it
is “Departure”, set the charging end time.
When the charging mode is set to “Departure”, set the “Climate
Prep” (
P. 157) to on or off.
To operate the air conditioning, press the “Climate Prep” button to set
the function to “ON”.
Each time the button is pressed, the function switches between “ON”
and “OFF”.
After setting operations are complete, press “Save”.
The charging schedule settings are saved and icons are added to the
charge schedule.
To cancel changing “Next Charging Event”, press
.
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
178
PRIUS PRIME_OM_OM47D71U_(U)
■
When charging schedule setting operations are canceled
When the vehicle is in the following conditions, charging schedule setting
operations are canceled.
●
The power switch is turned off before the settings are confirmed
●
The vehicle starts off
●
A display with a higher priority than that of the charging schedule setting is
shown
■
“Next Charging Event”
After charging completes, the “Next Charging Event” displayed on the display
will not change until the charging cable is removed, even after charging is
performed according to the “Next Charging Event” schedule.
■
To return to original setting after changing “Next Charging Event” set-
ting
Turning the setting of “Charge Now” on and then off can return the setting of
“Next Charging Event” to its original setting.
■
When “Next Charging Event” is changed while charging
●
When the charging mode is “Departure”, the current charging is interrupted
or continued depending on the remaining time until the charging is com-
pleted.
●
When the charging mode is “Start”, the current charging is interrupted, the
next charging will start at the set time.
■
Displaying advice related to charge schedule settings
When “?” is pressed on the “Edit Charging Event” screen (
P. 173), an
explanation of the setting item on the “Edit Charging Event” screen will dis-
play.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
179
2
Plug-
■
When the power switch is turned off
The next charge schedule (“Next
Charging Event”) can be checked on the
ending screen
*
that is displayed when the
power switch is turned off.
*
: The ending screen may not be dis-
played during charging.
WARNING
■
Cautions performing the setting operation
As the hybrid system needs to be operating during setting up the display,
ensure that the vehicle is parked in a place with adequate ventilation. In a
closed area such as a garage, exhaust gases including harmful carbon
monoxide (CO) may collect and enter the vehicle. This may lead to death or
a serious health hazard.
NOTICE
■
While performing the setting operation
To prevent 12-volt battery discharge, ensure that the hybrid system is oper-
ating while setting up the display features.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
180
PRIUS PRIME_OM_OM47D71U_(U)
When normal charging cannot be carried
out
Refer to the following table and carry out the appropriate correction
procedure.
When charging does not start, even though the normal proce-
dure is followed, check each of the following items.
If a message is shown on the multi-information display, also refer to
P. 185.
When normal charging cannot be carried out
Likely cause
Correction procedure
The power source indicator on the CCID (Charging Circuit Interrupting
Device) does not illuminate, even though the plug is connected to an
external power source.
Plug is not properly con-
nected to outlet
Check that the plug is properly connected to
the outlet.
Power is out
After power is restored, carry out the
charging procedure again.
Building breaker is tripped
and power is cut off
Check that the breaker is connected and if
there is no malfunction, check if the vehicle
can be charged through another outlet.
If charging is possible, the first outlet may
have a malfunction. Contact the building or
facility manager, or an electrician.
Short circuit between CCID
(Charging Circuit Interrupting
Device) and plug
Immediately stop charging and contact your
Toyota dealer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
181
2
Plug-
The error warning indicator on the CCID (Charging Circuit Interrupting
Device) flashes.
Electrical leakage detection
function or self- diagnostic
function operates and power
is cut off
When the voltage is insufficient, the error
warning indicator may flash when there is
noise interference. Perform a reset and con-
nect to a proper power source. (
If charging does not start, immediately stop
charging and contact your Toyota dealer.
Charging indicator does not illuminate, even though charging connector
is connected.
The plug is not properly con-
nected to the outlet
Check whether the plug is properly con-
nected to the outlet.
Charging connector is not
securely
connected
to
charging inlet
Check the connection status of the charging
connector.
• When connecting the charging connec-
tor, make sure not to touch the latch
release button. Insert the charging con-
nector securely until you hear a click. The
charging connector may not be connected
correctly if the latch release button is
pressed while inserting.
• After connecting the charging connector,
check that the latch release button is not
pressed and the charging indicator is
turned on.
If the charging indicator does not illuminate,
even though the charging connector is
securely connected, there may be a mal-
function in the system. Immediately stop
charging and contact your Toyota dealer.
Hybrid battery (traction bat-
tery) is already fully charged
When the hybrid battery (traction battery) is
fully charged, charging is not performed.
The charger does not oper-
ate
Please contact the facility manager when
there is a problem with charger.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
182
PRIUS PRIME_OM_OM47D71U_(U)
*
: Refer to P. 114 for details regarding charging indicator illumination and
flashing.
Refer to the following table and carry out the appropriate correction
procedure.
Charging indicator flashes and charging cannot be carried out.
When charging indicator
flashes
*
:
Charge schedule is regis-
tered
When you wish to charge according to the
charging schedule, wait until the set time.
To start charging, set “Charge Now” to “On”.
(
When charging indicator rap-
idly flashes
*
:
Malfunction occurred in an
external power source or the
vehicle
Start the hybrid system and follow the
instructions displayed by the message on
the multi-information display. (
When charging schedule function does not operate normally
Likely cause
Correction procedure
Cannot charge at desired time
Vehicle clock is not properly
adjusted
Check the clock settings and adjust it to the
proper time. (
The vehicle calendar is not
set correctly.
Check the calendar setting and set it to the
correct date. (
Charging cable is not con-
nected to vehicle
Before using the charging schedule, con-
nect the charging cable.
Incorrect charging mode
selected
Check the charging mode setting. (
When the charging mode is “Start”, charging
starts at the set time, but when it is “Depar-
ture”, charging is completed by the set time.
(The charging start time is automatically
controlled by the system.)
Cannot change charging schedule from smartphone application (vehi-
cles with 11.6-inch display)
*
Smartphone is outside its
coverage area
Check the signal strength. If the smart-
phone is outside its coverage area, move to
a place with a better signal.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
183
2
Plug-
Charging starts, even though charge schedule is registered
“Charge Now” is set to “On”
When charging according to the charging
schedule, set “Charge Now” to “Off”.
(
Charge schedule is set to
“Off”
Check that charge schedule is not set to
“Off”. (
Charging mode is set to
“Departure” and schedule
departure time is close to
current time
When the system determines that there is
no time to finish charging by the set sched-
uled departure time, it starts charging.
Check the charge schedules.
Charging
cable
was
removed
and
reinserted
while charging indicator was
flashing
If the charging cable is removed and rein-
serted while the charging indicator is flashing,
the charging schedule is canceled (
P. 149).
Temporarily remove the charging cable, and
then reconnect it.
The Remote Air Conditioning
System was operated
When the Remote Air Conditioning System
is operated, the system will start charging,
even if the charge schedule is registered. To
carry out charging using the charging
schedule, stop the Remote Air Conditioning
System, and then reconnect the charging
cable.
“Traction Battery Heater”
(
When the charging mode is set to “Depar-
ture”, “Traction Battery Heater” may operate
before charging starts. Check the status of
the charging indicator. (
Outside temperature is low
and hybrid battery (traction
battery) warming control
(
(Alaska and Canada only)
When hybrid battery (traction battery)
warming control operates, the charging
schedule are ignored and charging starts. In
order to protect the hybrid battery (traction
battery), allow charging to continue.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
184
PRIUS PRIME_OM_OM47D71U_(U)
*
: In order to use the smartphone application, it is necessary to apply to
Entune App Suite.
For details about Entune App Suite, refer to http://www.toyota.com/entune/.
Charging ends earlier than time set in “Departure”
Charging end time does not
match estimated end time
due to condition of power
source or outside tempera-
ture
If sudden changes in temperature or
changes in the condition of the power
source occur while charging, charging may
end earlier than the time estimated by the
system.
Charging is not complete, even though it is time set in “Departure”
“Climate Prep” is set to “On”
When “Climate Prep” is set to “On”, the air
conditioning operates until the set departure
time. Therefore, charging may not complete
by the set time due to charging conditions.
To have the hybrid battery (traction battery)
fully charged, allow charging to continue.
Charging end time does not
match estimated end time
due to condition of power
source or outside tempera-
ture
If sudden changes in temperature or
changes in the condition of the power
source occur while charging, charging may
not end exactly at the time estimated by the
system.
Charging does not start, even though it is time set in “Start”
Charging cable was con-
nected after set time
Connect the charging cable before the time
set in “Start”.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
185
2
Plug-
When the hybrid system is started
after charging, a message is dis-
played in the multi-information dis-
play.
When this occurs, follow the
instructions displayed on the
screen.
When charging-related message is displayed
Likely cause
Correction procedure
If “Charging Stopped Due to Pulled Charging Connector” is shown
Charging
connector
is
removed while charging
When the charging connector is removed
while charging, charging stops. If you want
to fully charge the hybrid battery (traction
battery), reconnect the charging connector.
After the hybrid battery (trac-
tion battery) is fully charged,
the charging connector is
removed while the hybrid
battery (traction battery) is
being
recharged
again
because electricity-consum-
ing functions
*
have been
used and the remaining
charge is now reduced.
*
:Electricity is consumed
when operating “Traction
Battery Heater” (
the air conditioning-linked
function (
P. 157) or
Remote Air Conditioning
System (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
186
PRIUS PRIME_OM_OM47D71U_(U)
If “Charging Stopped Due to Pulled Charging Connector” is shown
Charging connector is not
securely connected
Check the connection status of the charging
connector.
• When connecting the charging connec-
tor, make sure not to touch the latch
release button. Insert the charging con-
nector securely until you hear a click. The
charging connector may not be connected
correctly if the latch release button is
pressed while inserting.
• After connecting the charging connector,
check that the latch release button is not
pressed and the charging indicator is
turned on.
If charging cannot be carried out, even
though the proper procedures were fol-
lowed, have the vehicle inspected by your
Toyota dealer.
Latch release button of
charging
connector
was
pressed while charging
When the latch release button is pressed
while charging, charging stops. To continue
charging, reconnect the charging connector.
If “Charging Complete Limited Due to Battery Temp” is shown
Charging was stopped to
protect the hybrid battery
(traction battery) as it contin-
ued to remain hot for a cer-
tain period of time.
Allow the hybrid battery (traction battery) to
cool down and perform charging again if the
charging amount has not reached the
desired amount.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
187
2
Plug-
If “Charging Stopped Check Charging Source” is shown (1)
Problem in power supply
from external power source
Check the following items.
• Plug is not disconnected
• Power source indicator on the CCID
(Charging Circuit Interrupting Device) is
illuminated
• The circuit breaker has not tripped
If there is no problem with any of the above
items, there may be a problem with the out-
let of the building. Contact an electrician
and request an inspection. (Contact the
facility manager of the charging station
when there is a problem with charging sta-
tion.)
If charging cannot be carried out, even
though there is no problem with the power
source path, there may be a malfunction in
the system. Have the vehicle inspected by
your Toyota dealer.
Furthermore, if the error warning indicator
on the CCID (Charging Circuit Interrupting
Device) is flashing, there may be an electri-
cal leakage. Consult your Toyota dealer.
Charger
has
stopped
charging
• Charging may be canceled by an interrup-
tion of power supply depending on specifi-
cations of a charger. Refer to the
instructions of the charger.
• When charging is stopped using the
charger
• Equipment with charging schedule func-
tion
• Equipment that is not compatible with
the charging schedule function of the
vehicle
• Check if it is possible to charge with the
charging cable equipped to the vehicle.
If charging cannot be carried out, even
when using the genuine charging cable,
consult your Toyota dealer.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
188
PRIUS PRIME_OM_OM47D71U_(U)
If “Charging Stopped Check Charging Source” is shown (2)
Charger is not compatible
with vehicle
Check if it is possible to charge with the
charging cable equipped to the vehicle.
If charging cannot be carried out, even
when using the genuine charging cable,
consult your Toyota dealer.
Charger
has
stopped
charging
If “Charging Stopped Check Charging Source” is shown (3)
Problem in power supply
from external power source
Check the following items.
• Plug is securely inserted
• Extension cord is not used and outlet is
not overloaded
• Connected to a dedicated power line
• Electrical leakage has occurred or not
If there is no problem with any of the above
items, there may be a problem with the out-
let of the building. Contact an electrician to
request an inspection.
If charging cannot be carried out, even
though there is no problem with the power
source path, there may be a malfunction in
the system. Have the vehicle inspected by
your Toyota dealer.
Charger
has
stopped
charging
Check if it is possible to charge with the
charging cable equipped to the vehicle.
If charging cannot be carried out, even
when using the genuine charging cable,
consult your Toyota dealer.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
189
2
Plug-
If “Charging Stopped High Energy Use See Owner’s Manual” is shown
Power is being consumed by
electrical components of
vehicle
Check the following items, and then carry
out charging again.
• If the headlights and audio are turned on,
turn them off.
• Turn the power switch off.
If charging cannot be carried out, even after
performing the above, the auxiliary battery
may not be sufficiently charged. Operate
the hybrid system for approximately 15 min-
utes or more to charge the auxiliary battery.
If “Charging System Malfunction See Owner’s Manual” is shown
Malfunction
occurred
in
charging system
Have the vehicle inspected by your
Toyota dealer.
If “The Traction Battery became low temperature System put priority on
charging to preserve battery condition” is shown (Alaska and Canada
only)
The Hybrid battery (traction
battery) warming control was
operated (
When the hybrid battery (traction battery)
warning control operates, the charging
schedule is not used and charging is per-
formed. This is a control to protect the
hybrid battery (traction battery), and not a
malfunction.
Likely cause
Correction procedure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------
191
PRIUS PRIME_OM_OM47D71U_(U)
Instrument cluster
3
3.
Instrument cluster
Combination meter. . . 192
Warning lights and
indicators . . . . . . 201
Main display . . . . . .. 209
Multi-information
display. . . . . . . . 220
Head-up display . . . . 253
Energy monitor/
consumption screen
(vehicles with 7-inch
display) . . . . . . ... 261
Energy monitor/
consumption screen/
detail screen (vehicles
with 11.6-inch display) . 267
-------------------------------------------------------------------------------------------------------------------------------------------------------------
192
PRIUS PRIME_OM_OM47D71U_(U)
Combination meter
The units used on the display may differ depending on the target region.
Main display (
The main display shows basic information related to driving, such as the
vehicle speed and remaining fuel amount.
Multi-information display (
The multi-information display shows information which makes the vehicle
convenient-to-use, such as the hybrid system operation condition, electric-
ity consumption and fuel consumption history. Also, the operation contents
of the driving support systems and the combination meter display settings
can be changed by switching to the settings screen.
Warning lights and indicators (
The warning lights and indicators comes on or flashes to indicate problems
with the vehicle or to show the operation status of the vehicle’s systems.
Clock (
The large meter uses 2 liquid crystal displays to display informa-
tion such as the vehicle condition, driving status, electricity con-
sumption and fuel consumption.
Combination meter layout
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
193
3
Instrument clus
The meter control switches equipped on the steering wheel can be
used to switch the screen display and change settings related to func-
tions displayed on the screen.
Each time the button is
pressed, the mileage display
switches among odometer, trip
meters, etc., and the fuel con-
sumption information for each
distance switches as well.
(
Pressing
,
,
or
performs such operations as
scrolling the screen
*
, switching
the contents of the display
*
and
moving the cursor.
This button is used to perform such operations as selecting the cur-
rent item or switching between on and off.
When pressed, the display returns to the previous screen.
*
: On screens where the screen can be scrolled and the display can be
switched, marks are displayed to indicate the direction of operation (such
as
and
).
Operations related to the combination meter
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
194
PRIUS PRIME_OM_OM47D71U_(U)
When the switches are pressed, the instrument cluster light changes
as follows.
The instrument cluster brightness levels that can be selected differ
depending on whether the tail lights are on and surrounding brightness lev-
els. (
Darker
Brighter
When the switches are pressed,
the adjustment level check screen
(pop-up display
*
) is displayed on
the main display.
When the instrument cluster light is
adjusted, the brightness of the
instrument
panel
light
also
changes.
*
: A short time after the operation is completed, the pop-up display turns off.
Furthermore, the pop-up display can be turned on and off in the “Meter
Customize” settings. (
Instrument cluster light control
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
195
3
Instrument clus
Some information will be displayed automatically according to power
switch operation, vehicle condition, etc.
■
When starting the hybrid system
When the hybrid system starts,
an opening animation is dis-
played on the main display.
After the animation ends, the
screens switch to the normal
screen.
The opening animation will be
stopped in any of the following
situations.
• When the shift position is changed to other than P
• When the Simple Advanced Parking Guidance System (if equipped)
is turned on
■
When the driving assist systems are operating
When using driving assist systems such as the dynamic radar
cruise control with full-speed range (
P. 414) and LTA (Lane Trac-
ing Assist) (
P. 395), information related to each system is auto-
matically displayed on the multi-information display depending on
the situation.
For details regarding the displayed information and the contents of the
display, refer to the explanation page of each system.
■
When there is information to be notified about the vehicle
When a shift position is mistakenly selected or a problem occurs in
a vehicle system, a warning message (or image) is displayed on
the multi-information display.
When a warning message is displayed, follow the instructions displayed
on the display. (
Information automatically displayed
-------------------------------------------------------------------------------------------------------------------------------------------------------------
196
PRIUS PRIME_OM_OM47D71U_(U)
■
When stopping the hybrid system
●
When the hybrid system is stopped, the “Ending” screen is dis-
played on the multi-information display (for approximately 30
seconds
*
1
).
While the “Ending” screen is displayed, the following information
can be displayed by pressing
,
,
or
of the meter
control switches.
Score for each Eco score items (
Eco score result and advice
Driving time since the hybrid system started
Distance traveled since the hybrid system started
Average fuel consumption after the hybrid system started
Information for next charge schedule
*
2
On/off setting for “Charge Now” (
The setting can be switched each time
is pressed.
*
1
: The screen will be turned off immediately if the doors are locked.
*
2
: It can be displayed when the charge schedules are registered.
(
●
A check screen for “Traction Battery Cooler” may be displayed
when the hybrid system is stopped. (
1
2
3
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
197
3
Instrument clus
To adjust the time, perform operations on the
screen (
of the multi-information display.
■
Adjusting the time
Press
or
of the meter control switches on the steering
wheel and select
.
Press
or
of the meter control switches and select
.
Press
to display the cursor.
Press
or
of the
meter control switches to
adjust the cursor position,
and then press
or
to
change the setting.
When the 12-hour display is
selected, “12H” is displayed,
and when the 24-hour display is
selected, “24H” is displayed.
When adjusting minutes, operation automatically starts from 00 sec-
onds.
After changing the settings, press
to return to the previous screen.
Clock adjustment
1
2
3
4
-------------------------------------------------------------------------------------------------------------------------------------------------------------
198
PRIUS PRIME_OM_OM47D71U_(U)
■
Resetting the minutes display
Press
or
of the meter control switches on the steering
wheel and select
.
Press
or
of the
meter control switches and
select
.
Press
.
The minutes display switches to “00”.
*
*
: e.g. 1:00 to 1:29
1:00
1:30 to 1:59
2:00
1
2
3
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
199
3
Instrument clus
■
The meters and display illuminate when
The power switch is in ON mode.
■
Adjusting the instrument cluster brightness (
●
The brightness levels that can be selected differ depending on whether the
tail lights are on and surrounding brightness levels, as shown in the table
below.
*
: 22 levels of the brightness are displayed on the setting screen. However,
the brightness setting will be the brightest when other than 1st level (the
darkest) is selected. If other than 1st or 22nd level is selected, when the
tail lights are turned on in a dark place, the instrument cluster brightness
setting will be the selected level.
●
If the taillights are illuminated in a dark environment, the instrument cluster
light dims. However, when the brightness of the instrument cluster is set to
minimum or maximum (1st or 22nd level of the instrument cluster bright-
ness), even if the taillights are illuminated, the instrument cluster light will
not dim.
■
When disconnecting and reconnecting 12-volt battery terminals
The settings of the clock will be reset.
■
Calendar setting
●
Until the calendar setting is completed, the check screen is displayed every
time the power switch is turned to ON mode.
●
After the calendar information is set, it can be changed in the “Meter Cus-
tomize” settings. (
The tail lights are off
The tail lights are on
In a bright place
2 levels
*
2 levels
*
In a dark place
22 levels
If calendar recording is interrupted due to
replacement of the 12-volt battery or 12-
volt battery discharge, etc., when the
power switch is turned to ON mode after
maintenance, the calendar setting check
screen is automatically displayed on the
multi-information display.
●
If date information is not set, the electric-
ity and fuel consumption record cannot
be stored correctly. Also, the charging
schedule function can not operate prop-
erly. When the calendar setting check
screen is displayed, make sure to com-
plete the calendar setting. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
200
PRIUS PRIME_OM_OM47D71U_(U)
■
When the menu screen on the navigation system is operated (vehicles
with 11.6-inch display)
■
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
■
Pop-up display
Some functions, such as the driving mode select switch and air conditioning
system, are operation-linked and display pop-up screens on the multi-infor-
mation display. If the pop-up screens of these functions are not desired, they
can be turned off in the “Meter Customize” settings. (
A pop-up display of the menu screen icon
is displayed on the multi-information dis-
play.
*
*
: The pop-up display on the navigation
system can be turned off in the “Meter
Customize” settings. (
WARNING
■
To prevent an accident
■
Caution for use while driving
For safety, avoid operating the meter control switch while driving as much
as possible, and do not look continuously at the multi-information display
while driving. Stop the vehicle and operate the meter control switch. Failure
to do so may cause a steering wheel operation error, resulting in an unex-
pected accident.
NOTICE
■
The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
Do not place anything or attach a sticker
in front of the instrument cluster. The item
may obscure or obstruct the display, or
could reflect off the display, possibly
causing an accident.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
201
PRIUS PRIME_OM_OM47D71U_(U)
3
Instrument clus
Warning lights and indicators
The warning lights and indicators inform the driver of the status
of the vehicle’s various systems.
For the purpose of explanation, the following illustration dis-
plays all indicators and warning lights illuminated.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
202
PRIUS PRIME_OM_OM47D71U_(U)
Warning lights inform the driver of malfunctions in any of the vehicle’s
systems.
Warning lights
Warning lights
Pages
*
1
Brake system warning light (U.S.A.)
*
1
Brake system warning light (Canada)
(Red)
*
1
Brake system warning light
(Yellow)
*
1
Charging system warning light
*
1
Low engine oil pressure warning light
*
1
Malfunction indicator lamp (U.S.A.)
*
1
Malfunction indicator lamp (Canada)
*
1
SRS warning light
*
1
ABS warning light (U.S.A.)
*
1
ABS warning light (Canada)
*
1
Electric power steering system warning light
(Red/yellow)
*
1, 2
PCS warning light
LTA indicator (Orange)
*
1
Slip indicator light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
203
3
Instrument clus
*
1
: These lights turn on when the power switch is turned to ON mode to indi-
cate that a system check is being performed. They will turn off after the
hybrid system is on, or after a few seconds. There may be a malfunction in
a system if a light does not come on, or turn off. Have the vehicle
inspected by your Toyota dealer.
*
2
: The light flashes or illuminates to indicate a malfunction.
*
3
: The light flashes to indicate a malfunction.
*
1
High coolant temperature warning light
*
1, 3
PKSB OFF indicator (if equipped)
Open door warning light
Low fuel level warning light
Driver’s and front passenger’s seat belt
reminder light
Rear passengers’ seat belt reminder light
(U.S.A.)
Rear passengers’ seat belt reminder light
(Canada)
*
1
Master warning light
*
1
Tire pressure warning light
Warning lights
Pages
-------------------------------------------------------------------------------------------------------------------------------------------------------------
204
PRIUS PRIME_OM_OM47D71U_(U)
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Indicators
Pages
Turn signal indicator
Headlight indicator (U.S.A.)
Tail light indicator (Canada)
Parking brake indicator (U.S.A.)
Parking brake indicator (Canada)
Headlight high beam indicator
Fog light indicator (if equipped)
Security indicator
“READY” indicator
Shift position indicators
*
1, 2
Slip indicator light
*
1, 3
VSC OFF indicator
Cruise control indicator
Dynamic radar cruise control indicator
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
205
3
Instrument clus
*
1
: These lights turn on when the power switch is turned to ON mode to indi-
cate that a system check is being performed. They will turn off after the
hybrid system is on, or after a few seconds. There may be a malfunction in
a system if a light does not come on, or turn off. Have the vehicle
inspected by your Toyota dealer.
*
2
: The light flashes to indicate that the system is operating.
*
3
: The light comes on when the system is turned off.
*
4
: Depending on the operating condition, the color and illuminating/flashing
state of the light change.
Cruise control “SET” indicator
*
1, 3
PCS warning light
*
4
LTA indicator
Steering control indicator
Automatic High Beam indicator
Heated steering wheel indicator (if equipped)
“BSM” indicator (if equipped)
Intuitive parking assist indicator (if equipped)
*
1, 3
PKSB OFF indicator (if equipped)
*
1
S-APGS indicator (if equipped)
*
1
“AIR BAG ON/OFF” indicator (U.S.A.)
*
1
“AIR BAG ON/OFF” indicator (Canada)
Indicators
Pages
-------------------------------------------------------------------------------------------------------------------------------------------------------------
206
PRIUS PRIME_OM_OM47D71U_(U)
■
Main display and multi-information display
*
1
: The displayed indicator changes according to the current plug-in hybrid
system operation mode.
*
2
: The displayed indicator changes according to the current driving mode.
Indicators and symbols displayed on the display
Indicators
Pages
*
1
EV drive mode indicator
*
1
EV auto mode indicator
*
1
Hybrid battery charge mode indicator
*
2
“ECO MODE” indicator
*
2
“PWR MODE” indicator
EV indicator
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
207
3
Instrument clus
■
Multi-information display (symbol display
*
)
*
: These symbols are displayed along with a message. Also, the symbol dis-
plays listed here are only an example, and different symbols may be dis-
played according to the contents of the multi-information display.
Symbol display
Pages
Smart key system
Brake Override System/
Drive-Start Control/Parking Support
Brake function (if equipped)
LTA (Lane Tracing Assist)
Low engine oil pressure warning
(Canada only)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
208
PRIUS PRIME_OM_OM47D71U_(U)
■
BSM (Blind Spot Monitor) outside rear view mirror indicators
(if equipped) (
• When the BSM function is enabled on the
screen of the multi-infor-
mation display, the power switch is turned to ON mode.
If the system is functioning correctly, the BSM outside rear view mirror indi-
cators will turn off after a few seconds.
If the BSM outside rear view mirror indicators do not illuminate or do not
turn off, there may be a malfunction in the system.
If this occurs, have the vehicle inspected by your Toyota dealer.
●
Indicators are also displayed on the out-
side rear view mirrors.
●
In order to confirm operation, the BSM
outside rear view mirror indicators illumi-
nate in the following situations:
• When the power switch is in ON
mode, the BSM function is enabled
on the
screen of the multi-infor-
mation display.
WARNING
■
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the hybrid system, this could mean that these sys-
tems are not available to help protect you in an accident, which could result
in death or serious injury. Have the vehicle inspected by your Toyota dealer
immediately if this occurs.
NOTICE
■
To prevent damage to the engine and its components
The engine may be overheating if the high coolant temperature warning
light comes on or flashes. In this case, immediately stop the vehicle in a
safe place, and check the engine after it has cooled completely. (
-------------------------------------------------------------------------------------------------------------------------------------------------------------
209
PRIUS PRIME_OM_OM47D71U_(U)
3
Instrument clus
Main display
The units used on the display may differ depending on the target region.
The main display shows basic information, such as the vehicle
speed and remaining fuel amount. Also, the displayed informa-
tion can be switched according to user preference.
Display contents (vehicles without RSA [Road Sign Assist])
Simple screen
*
Split screen
*
*
: Refer to P. 215 for details on how to change the screen display.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
210
PRIUS PRIME_OM_OM47D71U_(U)
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C).
The temperature display flashes for approximately 10 seconds when the
outside temperature drops to approximately 37
F (3
C) or less, and then
stops flashing.
Mileage display (odometer/trip meters/driving range)
The possible driving range estimated from the mileage and current remain-
ing fuel amount can be displayed. (
Average fuel consumption display
The average electricity and fuel consumption that is linked with the con-
tents of the mileage display can be displayed. (
Sub-screen
When split screen is selected for the main display, information such as the
Hybrid System Indicator and current fuel consumption can be displayed.
(
1
2
3
4
5
6
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
211
3
Instrument clus
The units used on the display may differ depending on the target region.
Display contents (vehicles with RSA [Road Sign Assist])
-------------------------------------------------------------------------------------------------------------------------------------------------------------
212
PRIUS PRIME_OM_OM47D71U_(U)
Speedometer
Displays the vehicle speed
Fuel gauge
Displays the quantity of fuel remaining in the tank
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C).
The temperature display flashes for approximately 10 seconds when the
outside temperature drops to approximately 37°F (3°C) or less, and then
stops flashing.
Mileage display (odometer/trip meters/driving range)
The possible driving range estimated from the mileage and current remain-
ing fuel amount can be displayed. (
Average fuel consumption display
The average fuel consumption that is linked with the contents of the mile-
age display can be displayed. (
Sub-screen (when RSA [Road Sign Assist] is off)
Information such as the Hybrid System Indicator and current fuel con-
sumption can be displayed. (
Sub-screen (when RSA [Road Sign Assist] is on)
Displays information related to RSA (Road Sign Assist)
*
. (
*
: When RSA (Road Sign Assist) information is displayed in the
screen
of the multi-information display (
P. 245), RSA (Road Sign Assist) infor-
mation is not displayed on the sub-screen.
1
2
3
4
5
6
7
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PRIUS PRIME_OM_OM47D71U_(U)
213
3
Instrument clus
Each time
is pressed, the mileage display and fuel consumption
display change in the following order from 1 to 7.
Mileage display
Average fuel consumption dis-
play
After 1 to 7 are displayed, the dis-
plays return to 1.
Use the displayed average fuel
consumption as a reference.
Switching the mileage display and average fuel consumption
display
1
2
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст