Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 234
1GR-FE FUEL – FUEL TANK
FU–51
FU
10. CONNECT FUEL TANK BREATHER TUBE SUB-
ASSEMBLY
(a) Push the tube connector into the pipe until the
connector makes "click" sound.
NOTICE:
•
Check that there is no damage or foreign
objects on the connected part of the pipe.
•
After connecting, check if the pipe and the
connector are securely connected by pulling
them.
11. CONNECT FUEL TANK TO FILLER PIPE HOSE
(a) Connect the fuel tank to filler pipe hose, as shown in
the illustration, with the clamp.
12. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-
ASSEMBLY
(a) Install the fuel tank protector with the 4 nuts.
Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
(b) Install the fuel tank protector bracket with the 2 nuts.
(for automatic transmission)
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
O-Ring
Retainer
PUSH
O-Ring
Retainer
O-Ring
Retainer
A129910E01
A129909
A129913
A137217
FU–52
1GR-FE FUEL – FUEL TANK
FU
(c) Install the fuel tank protector bracket with the nut.
(for manual transmission)
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
13. INSTALL REAR FLOOR SERVICE HOLE COVER
(a) Connect the connector.
(b) Install the 3 screws from the center floor.
(c) Install the center floor silencer pad LH.
(d) Install the floor carpet.
14. INSTALL REAR DOOR SCUFF PLATE LH
(a) Engage the 6 claws and install the rear door scuff
plate.
A138100
A129908
A129904
A129907
A130152
1GR-FE FUEL – FUEL TANK
FU–53
FU
15. INSTALL FRONT DOOR SCUFF PLATE LH
(a) Engage the 14 claws and install the front door scuff
plate.
16. INSTALL REAR SEAT CUSHION ASSEMBLY LH
(a) Install the rear seat cushion assembly LH with the 2
bolts.
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
17. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
18. CHECK FOR FUEL LEAKAGE (See page
)
A130151
A129905
HORN – HORN SYSTEM
HO–1
HO
HORN SYSTEM
PRECAUTION
1.
DISCONNECT AND RECONNECT CABLE OF
NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable from the negative (-)
battery terminal, initialize the following systems after
the cable is reconnected.
(a) Before performing electronic work, disconnect the
cable from the negative (-) battery terminal in order
to prevent it from shorting and burning out.
(b) Before disconnecting and reconnecting the battery
cable, turn the ignition switch OFF and the headlight
dimmer switch OFF. Then loosen the terminal nut
completely. Do not damage the cable or terminal.
(c) When the battery cable is disconnected, the clock
and radio settings and stored DTCs are erased.
Therefore, before disconnecting the battery cable,
make a notes of them.
System Name
See procedure
METER / GAUGE SYSTEM
See page
Negative (-)
Battery Terminal
Cable
D033496E01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст