Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 261
INTERIOR – ROOF HEADLINING
IR–47
IR
(b) Tighten the 5 screws.
49. INSTALL REAR FLOOR BOARD
(a) Engage the clip and claw and install the rear floor
board.
(b) Install the luggage hold belt striker with the bolt.
HINT:
Use the same procedure for both sides.
50. INSTALL REAR SEATBACK ASSEMBLY RH (See
page
51. INSTALL REAR SEATBACK BOARD CARPET
ASSEMBLY RH (See page
)
52. INSTALL REAR SEATBACK ASSEMBLY LH (See
page
53. INSTALL REAR SEATBACK BOARD CARPET
ASSEMBLY LH (See page
54. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
B130592
B135075
for LH Side:
for RH Side:
Convex
Convex
B135074E01
INTRODUCTION – HOW TO USE THIS MANUAL
IN–1
IN
HOW TO USE THIS MANUAL
GENERAL INFORMATION
1.
GENERAL DESCRIPTION
(a) This manual is written in accordance with SAE
J2008.
(1) Diagnosis
(2) Removing / Installing, Replacing, Disassembling
/ Reassembling, Checking and Adjusting
(3) Final Inspection
(b) The following procedures are omitted from this
manual. However, these procedures must be
performed.
(1) Use a jack or lift to perform operations.
(2) Clean all removed parts.
(3) Perform a visual check.
2.
INDEX
(a) An alphabetical INDEX section is provided at the
end of the manual as a reference to help you find
the item to be repaired.
3.
PREPARATION
(a) Use of Special Service Tools (SST) and Special
Service Materials (SSM) may be required,
depending on the repair procedure. Be sure to use
SST and SSM when they are required and follow
the working procedures properly. A list of SST and
SSM is in the "Preparation" section of this manual.
4.
REPAIR PROCEDURES
(a) A component illustration is placed under the title
where necessary.
IN–2
INTRODUCTION – HOW TO USE THIS MANUAL
IN
(b) Non-reusable parts, grease application areas,
precoated parts and torque specifications are noted
in the component illustrations.
The following illustration is an example.
(c) Torque specifications, grease application areas and
non-reusable parts are emphasized in the
procedures.
HINT:
There are cases where such information can only
be explained by using an illustration. In these cases,
torque, oil and other information are described in the
illustration.
(d) Only items with key points are described in the text.
What to do and other details are explained using
illustrations next to the text. Both the text and
illustrations are accompanied by standard values
and notices.
(e) Illustrations of similar vehicle models are sometimes
used. In these cases, minor details may be different
from the actual vehicle.
(f)
Procedures are presented in a step-by-step format.
5.
SERVICE SPECIFICATIONS
(a) SPECIFICATIONS are presented in boldface text
throughout the manual. The specifications are also
found in the "Service Specifications" section for
reference.
Filter Cap
Float
Reservoir Tank
Slotted Spring Pin
15 (155,11)
Cylinder
Piston
Push Rod
Washer
Grommet
12 (120,9)
Gasket
: Specified torque
N*m (kgf*cm, ft.*lbf)
Non-reusable part
Clevis Pin
Clip
Clevis
Lock Nut
Boot
Snap Ring
Example:
N017080E11
Illustration
What to do and where to do it
Task heading
What work will be performed
Explanation text
•
How to perform the task
•
Information such as specifications and warnings, which are written
in boldface text
INTRODUCTION – HOW TO USE THIS MANUAL
IN–3
IN
6.
TERM DEFINITIONS
7.
INTERNATIONAL SYSTEM OF UNITS
(a) The units used in this manual comply with the
International System of Units (SI UNIT) standard.
Units from the metric system and the English
system are also provided.
Example:
Torque: 30 N*m (310 kgf*cm, 22 ft.*lbf)
CAUTION
Possibility of injury to you or other people.
NOTICE
Possibility of damage to components being repaired.
HINT
Provides additional information to help you perform repairs.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст