Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 449
SB–60
SEAT BELT – REAR SEAT OUTER BELT ASSEMBLY
SB
INSTALLATION
HINT:
The procedure described below is for the RH side. Use the
same procedure for both the RH and LH sides, unless
otherwise specified.
1.
INSTALL REAR SEAT OUTER BELT ASSEMBLY
(a) Check the angle of inclination required to lock the
retractor.
(1) Gently incline the retractor from its initial
position. Check that the belt does not lock
when the retractor is inclined 15
° or less in any
direction. Also, check that the belt locks when
the inclination of the retractor is 45
° or more.
NOTICE:
Do not disassemble the retractor.
If the operation is not as specified, replace the
rear seat outer belt.
(b) Hook the lower stay of the retractor onto the 2 body
hooks and provisionally install the retractor with the
2 bolts.
(c) Tighten bolt A and then bolt B.
Torque: 8.5 N*m (85 kgf*cm, 75 in.*lbf) for bolt A
42 N*m (430 kgf*cm, 31 ft.*lbf) for bolt B
(d) Install the through anchor with the bolt.
Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
(e) Make sure that the shoulder anchor rotates
smoothly.
(f)
Check that the ELR locks.
NOTICE:
Perform the check with the front seat outer belt
installed.
(1) With the belt installed, check that the belt locks
when it is pulled out quickly.
If the operation is not as specified, replace the
rear seat outer belt.
2.
INSTALL ROOF SIDE INNER GARNISH (See page
)
Lock
Unlock
45 °
B130782E01
B
A
B130780E01
B130781
SEAT BELT – REAR SEAT OUTER BELT ASSEMBLY
SB–61
SB
3.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY
(a) for RH Side:
(1) Engage the 6 clips and the 8 claws and install
the deck trim side panel.
(2) Tighten the 4 screws.
(b) for LH Side:
(1) Engage the 6 clips and the 8 claws and install
the deck trim side panel.
B130617
B130616
B130619
SB–62
SEAT BELT – REAR SEAT OUTER BELT ASSEMBLY
SB
(2) Tighten the 3 screws.
(c) Install the anchor plate with the bolt.
Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
(d) Make sure that the shoulder anchor plate rotates
smoothly.
4.
INSTALL REAR DECK TRIM COVER (w/ Power Outlet
Socket) (See page
)
5.
INSTALL LAP BELT OUTER ANCHOR COVER
(a) Engage the 3 claws and install the lap belt outer
anchor cover.
6.
INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/
Woofer) (See page
7.
INSTALL SPEAKER MOUNTING COVER (w/ Woofer)
(See page
)
8.
INSTALL DECK SIDE GARNISH (w/ Woofer) (See
page
9.
INSTALL QUARTER TRIM POCKET (w/o Woofer)
(See page
)
10. INSTALL SIDE TRIM COVER (w/o Woofer) (See page
)
11. INSTALL QUARTER TRIM POCKET TRAY (w/o
12. INSTALL PACKAGE HOLDER NET HOOK (w/o
Woofer)
HINT:
Use the same procedure for both sides.
(a) Install the package holder net hook with the screw.
B130618
B130615
B138385
B138474
SEAT BELT – REAR SEAT OUTER BELT ASSEMBLY
SB–63
SB
13. INSTALL FRONT DOOR OPENING TRIM
WEATHERSTRIP
(a) Install the front door opening trim weatherstrip.
14. INSTALL ACCESS DOOR SCUFF PLATE (See page
15. INSTALL FRONT DOOR SCUFF PLATE (See page
16. INSTALL REAR FLOOR MAT ASSEMBLY (See page
17. INSTALL LUGGAGE HOLD BELT STRIKER
ASSEMBLY (See page
)
18. INSTALL REAR FLOOR MAT SUPPORT PLATE (See
page
)
19. INSTALL REAR FLOOR BOARD (See page
)
20. INSTALL REAR SEATBACK ASSEMBLY
(a) for RH Side:
(1) Install the rear seatback assembly (See page
).
(b) for LH Side:
(1) Install the rear seatback assembly (See page
).
21. INSTALL REAR SEATBACK BOARD CARPET
ASSEMBLY
(a) for RH Side:
(1) Install the rear seatback board carpet assembly
(See page
(b) for LH Side:
(1) Install the rear seatback board carpet assembly
(See page
22. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
B138384
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст