Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 158
1GR-FE ENGINE MECHANICAL – CYLINDER HEAD
EM–65
EM
24 (245, 18)
24 (245, 18)
9.0 (92, 80 in.*lbf)
NO. 3 CAMSHAFT
9.0 (92, 80 in.*lbf)
NO. 4 CAMSHAFT
x8
19 (194, 14)
GROUND CABLE
8.0 (82, 71 in.*lbf)
19 (189, 14)
CONNECTOR
BRACKET
NO. 2 CHAIN
SUB-ASSEMBLY
CAMSHAFT TIMING
GEAR
CAMSHAFT TIMING
GEAR ASSEMBLY
100 (1,020, 74)
100 (1,020, 74)
30 (306, 22)
PLATE WASHER
Non-reusable part
N*m (kgf*cm, ft*lbf) : Specified torque
CYLINDER HEAD LH
NO. 2 CYLINDER
HEAD GASKET
NO. 3 CHAIN TENSIONER ASSEMBLY
x3
x3
1st: 36 (367, 27)
2nd: Turn 180°
x2
A126435E01
EM–66
1GR-FE ENGINE MECHANICAL – CYLINDER HEAD
EM
INNER COMPRESSION SPRING
VALVE LIFTER
VALVE SPRING RETAINER LOCK
Non-reusable part
VALVE SPRING RETAINER
VALVE STEM OIL O SEAL OR RING
VALVE SPRING SEAT
EXHAUST VALVE
INTAKE VALVE
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
INTAKE VALVE GUIDE BUSH
EXHAUST VALVE GUIDE BUSH
A126376E01
1GR-FE ENGINE MECHANICAL – CYLINDER HEAD
EM–67
EM
REMOVAL
1.
DISCHARGE FUEL SYSTEM PRESSURE
(See page
)
2.
REMOVE CHAIN SUB-ASSEMBLY
Refer to the procedures up to "REMOVE CHAIN SUB-
ASSEMBLY" (See page
).
3.
REMOVE NO. 1 COOL AIR INLET
(a) Remove the 2 bolts and the No. 1 cool air inlet.
4.
REMOVE EXHAUST PIPE STOPPER BRACKET (for
4WD)
(a) Remove the 2 bolts, then remove the exhaust pipe
stopper bracket.
5.
REMOVE NO. 2 FRONT EXHAUST PIPE ASSEMBLY
(a) Disconnect the oxygen sensor connector.
(b) Remove the 2 bolts and 2 nuts.
(c) Disengage the support and remove the front
exhaust pipe and 2 gaskets.
A129939
A126437
EM–68
1GR-FE ENGINE MECHANICAL – CYLINDER HEAD
EM
6.
REMOVE FRONT EXHAUST PIPE ASSEMBLY
(a) Disconnect the oxygen sensor connector.
(b) Remove the 2 bolts, 2 springs and 2 nuts, then
separate the front exhaust pipe from the exhaust
manifold RH.
7.
REMOVE MANIFOLD STAY
(a) Remove the 3 bolts and manifold stay.
8.
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
(a) Disconnect the air fuel ratio sensor connector.
(b) Remove the 6 nuts and exhaust manifold.
(c) Remove the gasket.
9.
REMOVE NO. 2 MANIFOLD STAY
(a) Remove the 3 bolts and the No. 2 manifold stay.
A126438
A126446
A126447
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст