Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 330
ME–52
METER – METER / GAUGE SYSTEM
ME
NG
OK
(a) Disconnect the E13 combination meter connector.
(b) Disconnect the E46 ECM connector.
(c) Measure the resistance.
Standard resistance
(d) Reconnect the ECM connector.
(e) Reconnect the combination meter connector.
NG
OK
GO TO SFI SYSTEM
2
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
16
32
31
35
28
20
17
9 10
34
11
6
5
13 14 15
23 24
26
12
3
2
1
4
27
29
18
7
30
19
8
21 22
25
33
Wire Harness Side:
Front View:
E13
TEMP
Front View:
Combination Meter Assembly Connector
ECM Connector
E46
THWO
E126864E02
Tester Connection
Specified Condition
E13-15 (TEMP) - E46-14 (THWO)
Below 1
Ω
E13-15 (TEMP) or E46-14 (THWO) -
Body ground
10k
Ω or higher
REPAIR OR REPLACE HARNESS AND
CONNECTOR
REPLACE COMBINATION METER ASSEMBLY
METER – METER / GAUGE SYSTEM
ME–53
ME
DESCRIPTION
The combination meter assembly controls the buzzers in accordance with signals from the front seat inner
belt assembly LH, center airbag sensor assembly and the main body ECU.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Check that the seat belt and key reminder buzzers
sound.
Warning Buzzer does not Sound
1
CHECK BUZZER (SEAT BELT, KEY REMINDER)
Front Seat Inner
Belt Assembly RH
Front Seat Inner Belt Assembly LH
Occupant Classification ECU
Combination Meter
Assembly
ES
Main Body ECU
Front Door Courtesy Switch LH
Unlock Warning Switch Assembly
Center Airbag Sensor Assembly
L
To Front Seat Outer Belt
(Driver Side)
RDC
+
E
PBKL
PBEW
FSP-
FSP+
FSR+
FSR-
BSW
BGND
RBE+
RBE-
KSW
DCTY
DCY2
KSWO
DOOR
KSW
E126876E01
ME–54
METER – METER / GAUGE SYSTEM
ME
Result
HINT:
•
Seat belt warning buzzer on: Ignition switch is ON,
driver or front passenger seat belt is unfastened, and
vehicle speed is 12.4mph (20 km/h) or more.
•
Key reminder warning buzzer on: Ignition switch is
OFF, key is in ignition key cylinder, and driver side
door is open.
B
C
D
A
(a) Disconnect the L19 front seat inner belt assembly (driver
side) connector.
(b) Measure the resistance.
Standard resistance
(c) Reconnect the front seat inner belt assembly (driver
side) connector.
NG
OK
(a) Disconnect the E13 combination meter assembly
connector.
(b) Disconnect the L19 front seat inner belt assembly (driver
side) connector.
Result
Proceed to
Seat belt warning buzzer does not sound (Driver side)
A
Seat belt warning buzzer does not sound (Passenger side)
B
Key reminder warning buzzer does not sound
C
No warning buzzers sound
D
Go to step 5
GO TO KEY REMINDER WARNING SYSTEM
REPLACE COMBINATION METER
ASSEMBLY
2
INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
Component Side:
Front Seat Inner Belt Assembly
(Driver Side) Connector
+
E
RDC
B137709E02
Tester Connection
Condition
Specified Condition
+ - E
Tongue plate fastened
10 k
Ω or higher
+ - E
Tongue plate
unfastened
Below 1
Ω
REPLACE FRONT SEAT INNER BELT
ASSEMBLY LH
3
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT
INNER BELT ASSEMBLY)
METER – METER / GAUGE SYSTEM
ME–55
ME
(c) Measure the resistance.
Standard resistance
(d) Reconnect the combination meter assembly connector.
(e) Reconnect the front seat inner belt assembly (driver
side) connector.
NG
OK
(a) Disconnect the L19 front seat inner belt assembly (driver
side) connector.
(b) Measure the resistance.
Standard resistance
(c) Reconnect the front seat inner belt assembly (driver
side) connector.
NG
OK
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch ON and turn the tester ON.
(c) Enter the following menus: DIAGNOSIS / SRS AIRBAG/
DTC INFO.
Wire Harness Side:
Front Seat Inner Belt Assembly
(Driver Side) Connector
Combination Meter Assembly Connector
Front View
Front View
E13
L19
+
L
B137678E02
Tester Connection
Specified Condition
E13-8 (L) - L19-3 (+)
Below 1
Ω
REPAIR OR REPLACE HARNESS OR
CONNECTOR
4
CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - BODY
GROUND)
Wire Harness Side:
Front Seat Inner Belt Assembly
(Driver Side) Connector
Front View
L19
+
E133659E01
Tester Connection
Specified Condition
L19-3 (+) - Body ground
Below 1
Ω
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPLACE COMBINATION METER ASSEMBLY
5
CHECK SUPPLEMENTAL RESTRAINT SYSTEM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст