Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 442
SB–32
SEAT BELT – FRONT SEAT INNER BELT ASSEMBLY
SB
(c) Remove the wire harness from the claw of the front
seat cushion inner shield.
(d) Remove the nut and the front seat inner belt.
INSPECTION
1.
INSPECT FRONT SEAT INNER BELT ASSEMBLY (for
Driver Side)
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance
between the terminals.
Standard resistance
If the result is not as specified, replace the front
seat inner belt.
B130777
Ohmmeter
B135157E01
Tester Connection
Condition
Specified Condition
10 - 11
Tongue plate fastened
Below 1
Ω
Tongue plate released
10 k
Ω or higher
SEAT BELT – FRONT SEAT INNER BELT ASSEMBLY
SB–33
SB
INSTALLATION
CAUTION:
Some of these service operations affect the SRS airbag
system. Read the precautionary notices concerning the
SRS airbag system before servicing (w/ Front Seat Side
Airbag) (See page
).
HINT:
The procedure described below is for the driver side. Use the
same procedure for both the driver and front passenger
sides, unless otherwise specified.
1.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
(a) Install the front seat inner belt with the bolt.
Torque: 42 N*m (430 kgf*cm, 31 ft.*lbf)
NOTICE:
Do not place the front seat inner belt over the
convex areas of the front seat frame adjuster.
(b) Install the wire harness into the claw of the front
seat cushion inner shield.
(c) for Driver Side:
(1) Install the 2 clamps and the 2 connectors.
(2) Connect the seat position sensor connector.
(d) for Front Passenger Side:
(1) Install the clamp and the connector.
(2) Connect the buckle switch connector.
2.
INSTALL FRONT SEAT ASSEMBLY (See page
3.
INSTALL FRONT SEAT TRACK COVER (See page
)
4.
CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
5.
INSPECT SRS WARNING LIGHT (w/ Front Seat Side
Airbag)
(See page
Convex
B130778E01
B130776
B130779
SB–34
SEAT BELT – FRONT SEAT OUTER BELT ASSEMBLY
SB
RESTRAINTS
SEAT BELT
FRONT SEAT OUTER BELT ASSEMBLY
COMPONENTS
ACCESS PANEL REAR
WEATHERSTRIP
CUP HOLDER
ACCESS DOOR INSIDE
HANDLE SUB-ASSEMBLY
LAP BELT OUTER
ANCHOR COVER
B138387E01
SEAT BELT – FRONT SEAT OUTER BELT ASSEMBLY
SB–35
SB
42 (430, 31)
FRONT SHOULDER BELT
ANCHOR ADJUSTER ASSEMBLY
x2
42 (430, 31)
CENTER PILLAR
UPPER GARNISH
x2
PRETENSIONER
CONNECTOR
FRONT SEAT OUTER
BELT ASSEMBLY
42 (430, 31)
42 (430, 31)
8.5 (85, 75 in.*lbf)
42 (430, 31)
42 (430, 31)
8.5 (85, 75 in.*lbf)
TENSION REDUCER
CONNECTOR
PRETENSIONER
CONNECTOR
FRONT SEAT OUTER
BELT ASSEMBLY
N*m (kgf*cm, ft.*lbf) : Specified torque
for LH Side:
ACCESS DOOR TRIM
BOARD SUB-ASSEMBLY
B135086E01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст