Volvo XC60 (2021 year). Manual in english — page 10
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
176
Panoramic roof
*
The panoramic roof is divided into two glass
sections. The front section can be opened
vertically at the rear edge (ventilation posi-
tion) or horizontally (open position). The rear
section cannot be moved.
The panoramic roof has a wind deflector and
sun curtain made of perforated fabric (located
beneath the glass sections) for extra protec-
tion in e.g. bright sunlight.
The panoramic roof and sun curtain are oper-
ated using the controls in the ceiling.
To operate the panoramic roof and sun cur-
tain, the ignition must be in mode
I
or
II
.
WARNING
Children, other passengers or objects can
be trapped by the moving parts.
•
Always operate the windows with cau-
tion.
•
Do not allow children to play with the
operating controls.
•
Never leave a child alone in the vehicle.
•
Remember to always cut the current to
the power windows by setting the
vehicle's electrical system to ignition
mode
0
and then taking the key with
you when leaving the vehicle.
•
Never stick objects or body parts out
through the windows, even if the vehi-
cle electrical system is completely
turned off.
•
Do not open the panoramic roof when
load carriers are installed.
•
Never place heavy objects on the pan-
oramic roof.
•
Remove ice and snow before opening
the panoramic roof. Be careful not to
scratch any surfaces or damage the
trim.
•
Do not operate the panoramic roof if it
is frozen in place.
Wind blocker
The panoramic roof is equipped with a wind
blocker that folds up when the roof is open.
Related information
•
•
Auto closing the panoramic roof
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
177
•
•
Locking and unlocking using the remote
key (p. 247)
Operating the panoramic roof
*
The panoramic roof and sun curtain are oper-
ated using a control in the ceiling panel, and
both are equipped with pinch protection.
WARNING
Children, other passengers or objects can
be trapped by the moving parts.
•
Always operate the windows with cau-
tion.
•
Do not allow children to play with the
operating controls.
•
Never leave a child alone in the vehicle.
•
Remember to always cut the current to
the power windows by setting the
vehicle's electrical system to ignition
mode
0
and then taking the key with
you when leaving the vehicle.
•
Never stick objects or body parts out
through the windows, even if the vehi-
cle electrical system is completely
turned off.
•
Do not open the panoramic roof when
load carriers are installed.
•
Never place heavy objects on the pan-
oramic roof.
•
Remove ice and snow before opening
the panoramic roof. Be careful not to
scratch any surfaces or damage the
trim.
•
Do not operate the panoramic roof if it
is frozen in place.
To operate the panoramic roof and sun cur-
tain, the ignition must be in mode
I
or
II
.
It can also be operated using keyless opening
*
with the door handle.
WARNING
Make sure that no child or other passenger
comes into contact with the windows as
they are closing with keyless closing
*
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
WINDOWS, GLASS AND MIRRORS
178
Check that the panoramic roof is properly
closed when closing.
The movement of the roof will stop if the con-
trol is released during manual operation or
when the glass has reached the comfort
4
or
fully open/closed position. The movement of
both the panoramic roof and the sun curtain is
also stopped if the control in the ceiling is
operated again in the direction opposite that
of the current direction of movement.
The panoramic roof and sun curtain are also
equipped with pinch protection. If there is any
problem with the pinch protection, a rest pro-
cedure can be tested.
For manual opening, the sun curtain must
be completely open before the panoramic
roof can be opened. For the reverse proce-
dure, the panoramic roof must be com-
pletely closed before the sun curtain can
be completely closed.
It may not be possible to operate the win-
dows in low temperatures.
Opening and closing ventilation
position
Ventilation position, rear edge raised.
Open by pushing the control upward
once.
Close by pushing the control downward
once.
When ventilation mode is selected, the rear
edge of the front section of the roof is raised.
If the sun curtain is fully closed when ventila-
tion position is selected, it will automatically
open approx. 50 mm (approx. 2 inches).
If the panoramic roof is closed from the venti-
lation position, the sun curtain will also auto-
matically close.
Fully opening and closing the
panoramic roof with the control in the
ceiling
Operation, manual mode
Operation, automatic mode
4
The comfort position is a position which helps keep wind and resonance sounds to a comfortably low level.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
179
Manual operation
1. To open the sun curtain, pull the control
backward to the manual open mode.
2. To open the panoramic roof to the comfort
position, pull the control backward a sec-
ond time to the manual opening position.
3. To open the panoramic roof fully, pull the
control backward a third time to the man-
ual opening position.
Close by repeating the above procedure in
reverse - push the control forward/down to
the manual closing position.
Auto operation
1. To open the sun curtain to the fully open
position, pull the control backward to the
auto open mode and release.
2. To open the panoramic roof to the comfort
position, pull the control backward a sec-
ond time to the automatic opening posi-
tion and release.
3. To open the panoramic roof fully, pull the
control backward a third time to the auto-
matic opening position and release.
Close by repeating the above procedure in
reverse - push the control forward/down to
the auto close position.
Automatic operation - rapid opening or
closing
The panoramic roof and sun curtain can be
opened or closed simultaneously:
–
Open - press the control backward twice
to the automatic operation position and
release.
–
Close - press the control forward/down
twice to the automatic operation position
and release.
Related information
•
•
Auto closing the panoramic roof
•
Pinch protection for windows and sun cur-
tains (p. 170)
•
•
Locking and unlocking using the remote
key (p. 247)
Auto closing the panoramic roof
*
sun curtain
With this function, the sun curtain closes
automatically 15 minutes after the vehicle has
been locked if it is parked in hot weather. This
is done to lower the passenger compartment
temperature and protect the upholstery
against being bleached by the sun.
The function is deactivated as the default fac-
tory setting and can be activated or deacti-
vated using the center display.
1. Tap
Settings
in the Top view in the center
display.
2. Tap
My Car
Locking
.
Select
Auto Close Sunroof Curtain
to
activate/deactivate.
The sun curtain also closes when all win-
dows are closed with keyless closing
*
.
Related information
•
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
180
•
•
Locking and unlocking using the remote
key (p. 247)
Wiper blades and washer fluid
The wipers and the washer fluid are designed
to improve visibility and the headlight pat-
tern.
Washer fluid direct from the wiper blades and
heating
*
of the wiper blades gives improved
vision.
When there is approximately 1 liter (1 qt) of
washer fluid remaining, a message to refill will
appear in the instrument panel.
Related information
•
Using the rain sensor (p. 181)
•
Using the windshield and headlight wash-
ers (p. 183)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
Using the rear window wiper/washer
(p. 184)
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
•
Using the windshield wipers (p. 180)
Using the windshield wipers
The windshield wipers are designed to clean
the windshield. The right-side steering wheel
lever is used to adjust windshield wiper set-
tings.
Right-hand steering wheel lever.
The thumb wheel is used to set rain sen-
sor sensitivity and interval wiper speed.
Single sweep
Move the lever down and release for a
single sweep.
Wipers off
Move the lever to position
0
to turn off
the windshield wipers.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
}}
181
Interval wipers
Move the lever upward to put the wip-
ers in interval wiping mode. Set the
number of sweeps per time unit with the
thumb wheel when interval wipers are
selected.
Continuous wipers
Move the lever upward for the wipers
to operate at normal speed.
Move the lever upward again for the
wipers to operate at high speed.
Before activating the wipers, make sure
that the wiper blades are not frozen in
place and that any snow or ice on the
windshield and rear window has been
scraped away.
Use plenty of washer fluid when the wipers
clean the windshield. The windshield must
be wet when the windshield wipers are
working.
Related information
•
Using the rain sensor (p. 181)
•
Using the windshield and headlight wash-
ers (p. 183)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Wiper blades and washer fluid (p. 180)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
Using the rear window wiper/washer
(p. 184)
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
Using the rain sensor
The rain sensor monitors the amount of water
on the windshield and automatically starts
the windshield wipers. Rain sensor sensitivity
can be adjusted using the thumb wheel on
the right-hand steering wheel lever.
Right-hand steering wheel lever.
Rain sensor button
Thumb wheel, sensitivity/interval wiper
speed
When the rain sensor is activated, the
rain sensor symbol will be displayed in the
instrument panel.
Activating the rain sensor
When the rain sensor is activated, the engine
must be running or the ignition in mode
I
or
II
while the windshield wiper lever is in position
0
or in the single sweep position.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
WINDOWS, GLASS AND MIRRORS
182
Activate the rain sensor by pressing the rain
sensor button
.
Move the lever downward for an extra wiper
sweep.
Turn the thumb wheel upward for increased
sensitivity and downward for decreased sensi-
tivity. The wipers will make one extra sweep
when the thumb wheel is turned upward.
Deactivate the rain sensor
Deactivate the rain sensor by pressing the
rain sensor button or moving the lever
upward to another wiper mode.
The rain sensor is automatically deactivated in
ignition mode
0
or when the engine is
switched off.
The rain sensor is also automatically deacti-
vated when the wiper blades are put in the
service position. The rain sensor will reactivate
when service mode is switched off.
The windshield wipers may start inadver-
tently and be damaged in automatic car
washes. Deactivate the rain sensor when
the engine is running or when the ignition
is in mode
I
or
II
. The symbol in the instru-
ment panel will go out.
Related information
•
Using the windshield and headlight wash-
ers (p. 183)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Wiper blades and washer fluid (p. 180)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
Using the rear window wiper/washer
(p. 184)
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
•
Using the windshield wipers (p. 180)
Activating and deactivating the
rain sensor's memory function
The rain sensor monitors the amount of water
on the windshield and automatically starts
the windshield wipers.
When the memory function is activated, the
rain sensor button does not need to be
pressed every time the vehicle is started:
1. Tap
Settings
in the center display's Top
view.
2. Tap
My Car
Wipers
.
3. Select
Rain Sensor Memory
to activate/
deactivate the memory function.
Related information
•
Using the rain sensor (p. 181)
•
Using the windshield and headlight wash-
ers (p. 183)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Wiper blades and washer fluid (p. 180)
•
Using the rear window wiper/washer
(p. 184)
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
183
•
Changing rear window wipers (p. 640)
•
Using the windshield wipers (p. 180)
Using the windshield and
headlight washers
The windshield and headlight washers are
designed to clean the windshield and head-
lights. Use the right-side steering wheel lever
to start the windshield and headlight wash-
ers.
Starting the windshield and headlight
washers
Washing function, right-hand steering wheel lever.
–
Move the right-hand steering wheel lever
toward the steering wheel to start the
windshield and headlight washers.
> After the lever is released, the wipers
make several extra sweeps.
Avoid activating the washer system when
it is frozen or the fluid reservoir is empty.
Otherwise, there is a risk of damaging the
pump.
Headlight washer
*
To save washer fluid, the headlights are
washed automatically according to a defined
interval when the headlights are on.
Reduced washing
When there is about 1 liter (1 qt) of washer
fluid left in the reservoir and the
Washer fluid
Level low, refill
message is displayed in the
instrument panel together with the
sym-
bol, the washer fluid supply to the headlights
is cut off. This is to prioritize windshield clean-
ing and visibility through it. The headlights are
only washed if high or low beam is on.
Related information
•
Using the rain sensor (p. 181)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Wiper blades and washer fluid (p. 180)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
184
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
•
Using the windshield wipers (p. 180)
Using the rear window wiper/
washer
The rear window washer/wiper is designed to
clean the rear window. Use the right-side
steering wheel lever to start and control the
wiper/washer.
Activating the rear window wiper/
washer
The rear window wiper motor is equipped
with overheating protection that switches
off the motor if it becomes overheated. The
rear window wiper can be operated again
after a cooling-down period.
Select
for interval rear window
wiper.
Select
for continuous rear window
wiper.
–
Move the right-side steering wheel lever
forward to wash/wipe the rear window.
Related information
•
Using the rain sensor (p. 181)
•
Using the windshield and headlight wash-
ers (p. 183)
•
Using automatic rear window wiping
when backing up (p. 185)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
Wiper blades and washer fluid (p. 180)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
185
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
•
Using the windshield wipers (p. 180)
Using automatic rear window
wiping when backing up
If reverse gear is engaged while the wind-
shield wipers are on, the rear window wipers
will start. This function is deactivated when a
different gear is selected.
1. Tap
Settings
in the Top view in the center
display.
2. Tap
My Car
Wipers
.
3. Select
Auto Rear Wiper
to activate/deac-
tivate automatic rear window wiping
when backing up.
If the rear window wipers are already in con-
tinuous wiper mode, no change will be made
when reverse gear is engaged.
Related information
•
Using the rain sensor (p. 181)
•
Using the windshield and headlight wash-
ers (p. 183)
•
Wiper blades and washer fluid (p. 180)
•
Activating and deactivating the rain sen-
sor's memory function (p. 182)
•
Using the rear window wiper/washer
(p. 184)
•
•
Putting the wiper blades in service posi-
tion (p. 642)
•
Replacing windshield wiper blades
(p. 641)
•
Changing rear window wipers (p. 640)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
188
Manual front seats
The front seats can be adjusted in a number
of different ways to help enhance your seat-
ing comfort.
Raise/lower the front edge of the seat
cushion
*
by moving the control up/down.
1
Change the length of the seat cushion
*
by
pulling up the lever and moving the cush-
ion forward/backward.
Move the seat forward/backing by lifting
the handle and moving the seat to a suita-
ble distance from the steering wheel and
pedals. Check to make sure the seat is
securely locked into place after its setting
has been changed.
Adjust lumbar support
*
by pressing the
button up/down/forward/rearward.
2
Raise/lower the seat by moving the con-
trol up/down.
Change the backrest tilt by turning the
knob on the backrest.
WARNING
•
Do not adjust the seat while driving.
The seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•
Check that the seat is securely locked
into position after adjusting.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
1
Only applies to the driver's seat.
2
Applies for four-way lumbar support
*
. Two-way lumbar support
*
is adjusted forward/rearward.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
189
Power
*
front seats
The front seats can be adjusted in a number
of different ways to help enhance your seat-
ing comfort. The power seat can be moved
forward/backward and up/down. The height
and length
*
of the seat cushion and the tilt of
the backrest can be adjusted. Lumbar sup-
port
*
can be adjusted up, down, forward and
backward.
3
The seats can be adjusted when the engine is
running and for a certain period of time after
the door has been unlocked without the
engine running. They can also be adjusted for
a short period after the engine is turned off.
The power seats have an overload protec-
tor that is triggered if a seat is blocked by
any object. If this occurs, remove the
object and attempt to adjust the seat
again.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Adjusting the power
*
front seats
Set the desired seating position using the
controls on the front seat cushion. To set the
convenience functions, turn the multifunction
control
4
upward/downward.
The illustration shows the controls in a vehicle with
four-way lumbar support
*
. Vehicles with two-way
lumbar support
*
do not have the rotary multifunction
control.
In vehicles with four-way lumbar support
*
,
turn the multifunction control
4
up/down to
set the convenience functions. In vehicles
with two-way lumbar support
*
, use the
round button to adjust the lumbar support
forward/rearward.
Raise/lower the front edge of the seat
cushion by moving the control up/down.
3
Applies for four-way lumbar support
*
. Two-way lumbar support
*
is adjusted forward/rearward.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
SEATS AND STEERING WHEEL
* Option/accessory.
190
Raise/lower the seat by moving the con-
trol up/down.
Move the seat forward/rearward by mov-
ing the control forward/rearward.
Change the backrest tilt by moving the
control forward/backward.
Only one movement (forward/rearward/up/
down) can be performed at a time.
The front seat backrests cannot be folded
down completely.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Storing positions for seats, mirrors
and head-up display
*
Adjustment settings for the power
*
seat, door
mirrors and head-up display
*
can be stored in
the memory buttons.
Two different positions for the power
*
seat,
door mirrors and head-up display
*
can be
stored using the memory buttons. The buttons
are located on the inside of either one or both
*
front doors.
Button
M
for storing a setting.
Memory button.
Memory button.
4
Not available in vehicles with two-way lumbar support
*
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
191
Storing positions
1. Adjust the seat, door mirrors and head-up
display to the desired position.
2. Press and hold the
M
button. The indica-
tor light in the button will illuminate.
3. Within three seconds, press and hold the
1
or
2
button.
> When the position has been stored in
the memory button, an audio signal will
sound and the indicator light in the
M
button will go out.
If none of the memory buttons are pressed
within three seconds, the
M
button will go out
and no position will be stored.
The seats, door mirrors or head-up display
must be readjusted before a new memory
position can be set.
For the stored positions to work, all driver
profiles need to be in
Protect Profile
mode.
Related information
•
•
•
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
•
Adjusting the door mirrors (p. 174)
•
•
Protecting a driver profile (p. 142)
Using stored positions for seats,
mirrors and head-up display
*
If the positions for the power
*
seat, door mir-
rors and head-up display
*
have been stored,
they can be activated using the memory but-
tons.
Using a stored position
A stored position can be used with the front
door open or closed:
Front door open
–
Briefly press one of the memory buttons
1
(
) or
2
(
). The power seats, door mir-
rors and head-up display will move and
stop at the positions stored in that button.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
SEATS AND STEERING WHEEL
* Option/accessory.
192
Front door closed
–
Press and hold one of the memory buttons
1
(
) or
2
(
) until the seat, door mirrors
and head-up display stop in the positions
stored in that memory button.
If the memory button is released, the seat,
door mirrors and head-up display will stop
moving.
WARNING
•
This list point needs to be translated
exactly to: "Because the driver's seat
can be adjusted with the ignition off,
children should never be left unatten-
ded in the vehicle.
•
Movement of the seat can be STOP-
PED at any time by pressing any but-
ton on the power seat control panel.
•
Do not adjust the seat while driving.
•
The seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•
The seat rails on the floor must not be
obstructed in any way when the seat is
in motion.
For the stored positions to work, all driver
profiles need to be in
Protect Profile
mode.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
•
Adjusting the door mirrors (p. 174)
•
Front seat massage
*
settings
The settings for the multifunctional seats can
be adjusted using either the mutifunction
control on the side of the seat or the center
display. The adjustment settings are shown in
the center display.
Multifunction control, located on the side of the seat
cushion.
Massage settings
The following massage settings are available:
•
On
/
Off
: Select
On
/
Off
to turn on/off the
massage function.
•
Programs 1-5
: There are 5 preset mas-
sage programs. Select
Swell
,
Tread
,
Advanced
,
Lumbar
or
Shoulder
.
•
Intensity
: Select
Low
,
Normal
or
High
.
•
Speed
: Select
Slow
,
Normal
or
Fast
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
193
Restarting the massage function
The massage function turns off automatically
after 20 minutes. The function is reactivated
manually.
–
Tap
Restart
, which is displayed in the
center display, to restart the selected mas-
sage program.
> The massage program will restart. If no
selection is made, the message will be
stored in Top view.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Adjusting front seat massage
settings
*
The settings for the multifunctional seats can
be adjusted using either the mutifunction
control on the seat or the center display. The
adjustment settings are shown in the center
display.
Adjusting front seat massage settings
The front seat backrests have a massage func-
tion. Air-filled cushions provide the massaging
action and a number of settings are available.
The massage function can only be activated
when the engine is running.
1. Activate the multifunction control by turn-
ing the control
upward/downward. The
seat settings view will appear in the center
display.
2. Select
Massage
in the seat settings view.
3. Select massage settings by tapping the
center display or by moving the cursor up/
down using the multifunction control's
upper
/lower
buttons. Change a set-
ting in the selected function by tapping
the arrows on the center display or by
using the multifunction control's front
/
rear
buttons.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст