Volvo V60 Recharge Plug-in Hybrid (2021 year). Manual in english — page 27
||
STARTING AND DRIVING
* Option/accessory.
458
Extreme weather conditions, towing a
trailer, high altitude and lower fuel grade
than recommended are factors that can
significantly increase the vehicle's fuel con-
sumption.
Trailer weights
WARNING
Please adhere to the recommendations
provided for trailer weight. If the recom-
mendations are not followed, the vehicle
and trailer may be difficult to control during
evasive maneuvers and braking.
The specified maximum trailer weights are
those permitted by Volvo. National vehicle
regulations may set additional restrictions
on trailer weight and speed. The trailer
hitches may be certified for higher towing
weights than the vehicle is permitted to
tow.
Self-leveling suspension
*
The vehicle's self-leveling system attempts to
keep the vehicle at a constant level, regardless
of load (up to the maximum permitted weight).
When the vehicle is stationary, the rear end of
the vehicle will be slightly lowered, which is
normal.
Driving in hilly terrain or hot weather
In certain conditions, there is a risk of over-
heating when driving with a trailer. If overheat-
ing of the engine and drive system is detected,
a warning symbol will illuminate in the instru-
ment panel and a message will appear.
The automatic transmission adapts the gear
for the current load and engine speed.
Steep inclines
Do not lock the automatic transmission into a
higher gear than what the engine can handle
‒
it is not always preferable to drive in high
gears at low rpm.
Parking on a hill
1. Depress the brake pedal.
2. Apply the parking brake.
3. Put the gear selector in
P
.
4. Release the brake pedal.
Put chocks behind the wheels when the vehi-
cle is parked on a hill with a trailer attached.
Starting on a hill
1. Depress the brake pedal.
2. Put the gear selector in
D
.
3. Release the parking brake.
4. Release the brake pedal and start driving.
Related information
•
•
Checking trailer lights (p. 460)
•
Towing capacity and tongue weight
(p. 652)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
* Option/accessory.
459
Trailer Stability Assist
*
Trailer Stability Assist (TSA
11
) is part of the
ESC
12
stability system and is a function
designed to help stabilize a vehicle that is
towing a trailer when the vehicle and trailer
have begun to sway. The function is added
when installing a towbar. Contact a Volvo
retailer for more information.
Reasons for swaying
A vehicle towing a trailer may begin to sway
for various reasons. Normally this only occurs
at high speeds. However, if the trailer is over-
loaded or unevenly distributed, e.g. too far
back, there is a risk of swaying even at low
speeds.
Swaying may be caused by factors such as:
•
The vehicle and trailer are hit by a sudden,
strong crosswind.
•
The vehicle and trailer are traveling on an
uneven road or over a bump.
•
Sudden movements of the steering wheel.
Once swaying has begun, it can be difficult or
impossible to stop it. This makes the vehicle
and trailer difficult to control and there is a risk
of swerving into oncoming traffic or driving off
the road.
Trailer Stability Assist function
Trailer Stability Assist continuously monitors
the vehicle's movements, particularly lateral
movements. If swaying is detected, the brakes
are applied individually on the front wheels,
which has a stabilizing effect on the vehicle
and trailer. This is often enough to enable the
driver to regain control of the vehicle.
If the Trailer Stability Assist function's first
attempt is not adequate to stop the swaying
motion, the brakes are applied on all wheels
and engine power is temporarily reduced. As
the swaying motion begins to decrease and
the vehicle and trailer have once again
become stable, TSA stops regulating the
brakes/engine power and the driver regains
control of the vehicle.
Trailer Stability Assist is deactivated if the
driver activates
ESC Sport Mode
in the
center display's menu system.
Trailer Stability Assist may not intervene if the
driver tries to compensate for the swaying
motion by moving the steering wheel rapidly,
because the system will then not be able to
determine if it is the trailer or the driver caus-
ing the swaying.
When Trailer Stability Assist
is activated, the ESC symbol
is displayed in the instrument
panel.
A vehicle software update is required when
a towbar is retrofitted. Contact a Volvo
retailer.
Related information
•
Driving with a trailer (p. 457)
•
Electronic Stability Control (p. 269)
11
Trailer Stability Assist
12
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
* Option/accessory.
460
Checking trailer lights
When connecting a trailer, make sure that all
of the lights on the trailer are functioning
before starting to drive.
Trailer turn signals and brake lights
If one or more of the turn signals or brake
lights on the trailer is not working, a symbol
and message will be displayed in the instru-
ment panel. The other lights on the trailer
must be checked manually by the driver before
the vehicle is driven.
Symbol Message
•
Trailer turn indicator
Right
turn indicator malfunction
•
Trailer turn indicator
Left
turn indicator malfunction
•
Trailer brake light
Malfunc-
tion
If any of the trailer's turn signal lights is not
working, the turn signal symbol in the instru-
ment panel will also flash more quickly than
normal.
Trailer rear fog light
When a trailer is connected, the vehicle's rear
fog light may not illuminate and rear fog light
functionality is instead transferred to the
trailer. If this is the case, check to see if the
trailer is equipped with a rear fog light before
activating the vehicle's fog lights when driving
with a trailer to help ensure safe operation.
Checking trailer lights
*
Automatic check
When the trailer has been connected to the
vehicle's electrical system, its lights can be
checked by automatically activating them.
This function helps the driver check that the
trailer's lights are functioning correctly before
starting to drive.
In order to perform this check, the vehicle
must be switched off.
1. When a trailer is connected to the towbar,
the message
Automatic Trailer Lamp
Check
will appear in the instrument panel.
2. Acknowledge the message by pressing
the
O
button on the right-side steering
wheel keypad.
> The light check will begin.
3. Get out of the vehicle to perform the
check.
> All of the lights on the trailer will begin
flashing, and then illuminate separately
one at a time.
4. Visually check that all of the trailer's lights
are functioning correctly.
5. After a short time, all of the trailer's lights
will start flashing again.
> The light check is completed.
Disabling the automatic check
The automatic light check can be disabled in
the center display.
1. Tap
Settings
in the Top view.
2. Tap
My Car
Lights and Lighting
.
3. Deselect
Automatic Trailer Lamp
Check
.
Manual check
If the automatic check has been disabled, the
check can be started manually.
1. Tap
Settings
in the Top view.
2. Tap
My Car
Lights and Lighting
.
3. Select
Manual Trailer Lamp Check
.
> The light check will begin. Get out of
the vehicle to perform the check.
Related information
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
}}
461
Towing using a towline
This section refers to one vehicle being towed
behind another using a towline.
Never attempt to tow the vehicle behind
another vehicle as this could damage the elec-
tric motor. The vehicle must instead be lifted
onto a tow truck and transported with all four
wheels on the bed or lifting platform of the
truck (no wheels may touch the road).
Towing another vehicle
Towing another vehicle requires a lot of power
- use the
Constant AWD
drive mode. This
helps charge the hybrid battery and improve
the vehicle's driving and roadholding characte-
ristics.
Before towing another vehicle, check applica-
ble speed limit regulations.
Jump starting
Never attempt to tow the vehicle to start the
engine, as this could damage the electric
motor. Use an auxiliary battery if the start bat-
tery's charge level is so low that the engine
cannot be started.
Attempts to tow-start the vehicle could
cause damage to the electrical drive motor
and three-way catalytic converter.
Related information
•
Attaching and removing the towing eyelet
(p. 461)
•
Hazard warning flashers (p. 159)
•
•
Jump starting using another battery
(p. 455)
•
Selecting ignition mode (p. 416)
•
Attaching and removing the
towing eyelet
Use the towing eyelet to tow another vehicle.
Screw the towing eyelet securely into place
in the threaded outlet behind the cover on the
right-hand side of the rear bumper.
If the vehicle is equipped with a towbar,
there is no rear attachment for the towing
eye.
Attaching the towing eyelet
Take out the towing eyelet, which is
stored in a foam block under the floor in
the cargo compartment.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
STARTING AND DRIVING
* Option/accessory.
462
Remove the cover by pressing on the
mark with a finger while folding out the
opposite side/corner.
> The cover turns along its center line and
can then be removed.
3. Screw the towing eyelet in as far as possi-
ble.
Fasten the eyelet securing by, for example,
inserting a lug wrench
*
through it and
using this as a lever.
It is important that the towing eye is
screwed in securely as far as possible.
Removing the towing eyelet
–
Unscrew the towing eyelet after use and
return it to the foam block.
Replace the cover on the bumper.
Related information
•
Towing using a towline (p. 461)
•
•
Recovery
This section refers to transporting the vehicle
with a tow truck or similar vehicle.
Call a professional towing service for assis-
tance.
In certain conditions, the towing eyelet can be
used to pull the vehicle onto a flatbed tow
truck.
Note that the vehicle must always be
towed raised with all wheels on the tow
truck.
The vehicle's location and ground clearance
determine if it can be lifted onto a tow truck. If
the incline of the tow truck is too steep or if
the ground clearance under the vehicle is
insufficient, attempting to pull it up may result
in damage. In this case, the vehicle should
only be lifted with the tow truck's lifting equip-
ment.
WARNING
No person or object should be behind the
tow truck when the vehicle is lifted onto
the bed of the truck.
Related information
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
}}
* Option/accessory.
463
HomeLink
®
*
13
HomeLink
®
14
is a programmable remote con-
trol, integrated in the vehicle electrical sys-
tem, that can control up to three different
devices (e.g. garage door opener, alarm sys-
tem, outdoor and indoor lighting) and thereby
replace the remote controls for these.
General
The illustration is generic – the design may vary.
Button 1
Button 2
Button 3
Indicator light
HomeLink
®
is delivered integrated in the rear-
view mirror. The HomeLink
®
panel consists of
three programmable buttons and an indicator
light in the mirror.
For more information about HomeLink
®
,
please visit: homelink.com or call
1–800–355–3515.
Save the original remote controls for future
programming (e.g. for use in another vehicle).
The button programming should be cleared
if the vehicle is sold.
Related information
•
•
•
Programming HomeLink
®
*
15
Follow these instructions to program
HomeLink
®
, reset all programming, or pro-
gram individual buttons.
In some vehicles, the ignition must be on
or in the "accessory position" before
HomeLink
®
can be programmed or used. It
can be a good idea to put new batteries in
the remote control being replaced by
HomeLink
®
for faster programming and
better radio signal transmission. The
HomeLink
®
buttons should be reset before
programming.
WARNING
While HomeLink
®
is being programmed,
the garage door or gate being programmed
may be activated. Make sure that no one is
near the door or gate during programming.
When programming a garage door opener,
it is advised to park outside of the garage.
13
Certain markets only.
14
HomeLink and the HomeLink house symbol are registered trademarks of Gentex Corporation.
15
Certain markets only.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
STARTING AND DRIVING
464
1. Point the remote control at the
HomeLink
®
button to be programmed and
hold it about 2-8 cm (1-3 inches) from the
button. Do not obstruct the HomeLink
®
indicator light.
Note:
Some remote controls are more
effective at programming HomeLink
®
from
a distance of about 15-20 cm (6-12
inches). Keep this in mind if you experi-
ence any programming difficulties.
2. Press and hold both the remote control
button and the HomeLink
®
button to be
programmed.
3. Do not release the buttons until the indica-
tor light has stopped flashing slowly
(about once a second) and either flashes
quickly (about 10 times a second) or
glows steadily.
>
If the indicator light glows steadily:
Indication that programming is com-
plete. Press the programmed button
twice to activate.
If the indicator light flashes quickly:
The device being programmed with
HomeLink
®
may have a security func-
tion that requires an extra step. Try
pressing the programmed button twice
to see whether the programming
works. Otherwise, continue with the
following steps.
4. Locate the "training" button
16
on the
receiver for the e.g. garage door opener. It
is usually located near the antenna bracket
on the receiver.
5. Press and release the "training" button
once. Programming must be completed
within 30 seconds after pressing the but-
ton.
6. Press and release the HomeLink
®
button
to be programmed. Repeat the press/
hold/release sequence a second time. For
some receivers, the sequence may need to
be repeated a third time.
> Programming is now completed and
the garage door, gate, etc. should now
be activated when the programmed
button is pressed.
If you experience any difficulties programming,
please contact HomeLink
®
or call 1–800–355–3515.
16
The name and color of the button varies depending on the manufacturer.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
* Option/accessory.
465
Programming individual buttons
To program an individual HomeLink
®
button:
1. Press and hold the desired button for
about 20 seconds.
2. When the indicator light on HomeLink
®
starts flashing slowly, it is possible to pro-
gram as usual.
Note:
If the button you are reprogram-
ming does not program with a new
device, it will return to the previously
saved programming.
Resetting the HomeLink
®
buttons
It is only possible to reset all HomeLink
®
but-
tons at once. It is not possible to reset individ-
ual buttons. Individual buttons can only be
reprogrammed.
–
Press and hold the outer buttons (1 and 3)
on HomeLink
®
for about 10 seconds.
> When the indicator light goes from a
steady glow to flashing, the buttons
have been reset and are ready for
reprogramming.
Related information
•
•
•
Using HomeLink
®
*
17
Once HomeLink
®
is programmed, it can be
used instead of the separate remote controls.
Press and hold the programming button. The
garage door, gate, alarm system, etc. will be
activated (this may take several seconds). If
the button is held down for more than 20 sec-
onds, reprogramming will begin. The indicator
light will glow steadily or flash when the but-
ton has been pressed. The original remote
controls may be used concurrently with
HomeLink
®
if desired.
When the ignition is switched off,
HomeLink
®
will be active for at least
7 minutes.
HomeLink
®
cannot be used if the vehicle is
locked and the alarm is armed
*
from the
outside.
WARNING
•
If you use HomeLink
®
to open a garage
door or gate, be sure no one is near the
gate or door while it is in motion.
•
Do not use HomeLink
®
with any
garage door opener that lacks safety
stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982). A
garage door that cannot detect an
object - signaling the door to stop and
reverse - does not meet current U.S.
federal safety standards. For more
information, contact HomeLink at:
homelink.com.
Related information
•
•
•
17
Certain markets only.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
* Option/accessory.
466
Type approval for HomeLink
®
*
18
FCC (USA) and IC (Canada)
This device complies with FCC rules part 15
and Industry Canada RSS-210. Operation is
subject to the following two conditions: (1)
This device may not cause harmful interfer-
ence, and (2) This device must accept any
interference that may be received including
interference that may cause undesired opera-
tion.
WARNING
The transmitter has been tested and com-
plies with FCC and IC rules. Changes or
modifications not expressly approved by
the party responsible for compliance could
void the user's authority to operate the
device.
19
Type approval for EU
Gentex Corporation hereby declares that
HomeLink
®
Model UAHL5 complies with the
Radio equipment directive 2014/53/EU.
Wavelengths within which the radio equip-
ment operates:
•
433.05MHz-434.79MHz <10mW E.R.P.
•
868.00MHz-868.60MHz <25mW E.R.P.
•
868.70MHz-868.20MHz <25mW E.R.P.
•
869.40MHz-869.65MHz <25mW E.R.P.
•
869.70MHz-870.00MHz <25mW E.R.P.
Certificate holder address: Gentex Corpora-
tion, 600 North Centennial Street, Zeeland MI
49464, USA
For further details, search for support informa-
tion on type approval at volvocars.com
Related information
•
Compass
*
An integrated compass
20
in the upper right
corner of the rearview mirror shows the
direction the vehicle is traveling.
Rearview mirror with compass.
Eight different compass directions are shown
with the abbreviations:
N
(north),
NE
(north-
east),
E
(east),
SE
(southeast),
S
(south),
SW
(southwest),
W
(west) and
NW
(northwest).
Related information
•
Activating and deactivating the compass
•
18
Certain markets only.
19
The term "IC:" before the certification/registration number only signifies that Industry Canada technical specifications were met.
20
Rearview mirror with compass is available as an option only on certain markets and models.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING AND DRIVING
}}
* Option/accessory.
467
Activating and deactivating the
compass
*
An integrated compass
21
in the upper right
corner of the rearview mirror shows the
direction the vehicle is traveling.
The compass is automatically activated when
the vehicle is started.
To deactivate/activate the compass manually:
–
Use a paper clip or similar object to press
the button on the bottom of the mirror.
> If the compass is deactivated when the
vehicle is switched off, it will not be
activated the next time the vehicle is
started. The compass will then need to
be activated manually.
Related information
•
•
Calibrating the compass
*
The globe is divided into 15 magnetic zones.
The compass
22
should be calibrated if the
vehicle is driven from one zone to another.
1. Stop the vehicle in a large, open area away
from steel constructions and high-voltage
power lines.
2. Start the engine and switch off all electri-
cal equipment (climate system, wipers,
etc.) and make sure all doors are closed.
Calibration may fail or not even be initiated
if electrical equipment is not turned off.
3. Hold the button on the bottom of the rear-
view mirror pressed for about 3 seconds
(using e.g. a paper clip). The number of the
current magnetic zone is shown.
15
14
13
12
11
9
8
7
6
5
4
3
2
1
10
Magnetic zones.
4. Press the button on the underside of the
mirror repeatedly until the desired mag-
netic zone (
1–15
) appears (see the map of
magnetic zones).
5. Wait until the display again shows
C
, or
press and hold the button on the under-
side of the rearview mirror for approx.
6 seconds until
C
is displayed.
6. Drive slowly in a circle at a speed of no
more than 10 km/h (6 mph) until a com-
pass direction is shown in the display. This
indicates that calibration is complete.
Drive in a circle two more times to fine-
tune the calibration.
21
Rearview mirror with compass is available as an option only on certain markets and models.
22
Rearview mirror with compass is available as an option only on certain markets and models.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
STARTING AND DRIVING
* Option/accessory.
468
7.
Vehicles with heated windshields
*
:
If
C
is shown in the display when the wind-
shield heating function is activated, per-
form step 6 above with the heating func-
tion on.
8. Repeat the above procedure as needed.
Related information
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
AUDIO, MEDIA AND INTERNET
* Option/accessory.
470
Audio, media and Internet
The audio and media system consists of a
media player and a radio. A cellular phone can
also be connected through Bluetooth to use
hands-free functions or play music in the
vehicle. When the vehicle is connected to the
Internet, it is also possible to use apps to play
media.
Audio and media overview
The functions can be controlled using voice
commands, the steering wheel keypad or the
center display. The number of speakers and
amplifiers varies depending on the audio sys-
tem installed in the vehicle.
System updates
The audio and media system is continuously
improved. It is recommended to download
system updates as soon as they are available.
Related information
•
•
•
•
•
•
•
•
•
Handling system updates via Download
Center (p. 586)
•
License agreement for audio and media
(p. 525)
Sound settings
Sound reproduction quality is preset but can
also be adjusted.
The system's volume is normally adjusted
using the volume control below the center dis-
play or the right-side steering wheel keypad.
This applies, for example, when playing music
or the radio or during phone calls and active
traffic messages.
Sound reproduction
The audio system is precalibrated using digital
signal processing. This calibration takes into
account speakers, amplifiers, passenger com-
partment acoustics, listener position, etc. for
each combination of vehicle model and audio
system. There is also a dynamic calibration
that takes into account the volume control set-
ting and the vehicle's speed.
Personal settings
Different settings are available in Top view
under
Settings
Sound
depending on the
vehicle's sound system.
Premium Sound
*
(Bowers & Wilkins)
•
Tone
- setting for e.g. bass, treble, equal-
izer, etc.
•
Balance
- balance between right/left and
front/rear speakers.
•
System Volumes
– adjusts volume in the
various systems of the car, e.g.
Voice
-------------------------------------------------------------------------------------------------------------------------------------------------------------
AUDIO, MEDIA AND INTERNET
* Option/accessory.
471
Control
,
Park Assist
and
Phone
Ringtone
.
High Performance Pro
*
(Harman
Kardon)
•
Equalizer
- setting of equalizer.
•
Balance
- balance between right/left and
front/rear speakers.
•
System Volumes
– adjusts volume in the
various systems of the car, e.g.
Voice
Control
,
Park Assist
and
Phone
Ringtone
.
High Performance
•
Tone
- setting for e.g. bass, treble, equal-
izer, etc.
•
Balance
- balance between right/left and
front/rear speakers.
•
System Volumes
– adjusts volume in the
various systems of the car, e.g.
Voice
Control
,
Park Assist
and
Phone
Ringtone
.
Related information
•
•
•
Voice control settings (p. 148)
•
•
Audio, media and Internet (p. 470)
•
Sound experience
*
Sound experience is an app that provides
access to additional sound settings.
Open
Sound Experience
from the center dis-
play's App view. Depending on the sound sys-
tem installed in the vehicle, the following set-
tings are possible:
Premium Sound
*
(Bowers & Wilkins)
•
Studio
– sound settings can be adjusted
to be primarily adapted for
Driver
,
All
and
Rear
.
•
Individual stage
- surround sound mode
with settings for intensity and enclosure.
•
Concert hall
- reproduces the acoustics
of Gothenburg's Concert Hall.
•
Jazz club
– reproduces the acoustics of
the Nefertiti Jazz Club.
Reproduces the acoustics of the Nefertiti Jazz Club.
High Performance Pro
*
(Harman
Kardon)
•
Seat Optimization
– sound settings can
be adjusted to be primarily adapted for
Driver
,
All
and
Rear
.
•
Surround
- surround sound mode with
level settings.
•
Tone
- setting for e.g. bass, treble, equal-
izer, etc.
Related information
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
AUDIO, MEDIA AND INTERNET
* Option/accessory.
472
Apps
The App view contains apps that provide
access to certain vehicle services.
Swipe the center display screen from right to
left
1
to access the App view from the Home
view. This view displays downloaded apps
(third-party apps) as well as apps for inte-
grated functions, such as
FM radio
.
App view. (generic illustration; basic apps vary
depending on market and model)
Several basic apps are always available. More
apps such as web radio and music services
can be downloaded when the car is connected
to the Internet.
Some apps can only be used when the vehicle
is connected to the Internet.
Start an app by pressing the app in the center
display's app view.
All apps used should be updated to the latest
version.
Related information
•
•
•
•
•
•
•
Hard disk storage space (p. 524)
•
Terms of use and data sharing (p. 522)
1
Applies for left-hand drive vehicles. For right-hand drive vehicles, swipe in the other direction.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
AUDIO, MEDIA AND INTERNET
}}
* Option/accessory.
473
Download apps
New apps can be downloaded when the vehi-
cle is connected to the Internet.
Data downloading can affect other services
such as transfer data, e.g. web radio. If the
affect on other services is experienced as
problematic, the download can be interrup-
ted. Alternatively, it may be appropriate to
switch off or cancel other services.
When downloading using a phone, pay
extra attention to the data traffic costs.
1. Open the
Download Center
app in App
view.
2. Select
New apps
to open a list of apps
that are available but are not installed in
the vehicle.
3. Tap on the row for an app in order to
expand in the list and get more informa-
tion about the app.
4. Select
Install
to start the download and
installation of the app.
> The current status of the download and
installation will be shown.
If a download cannot be started imme-
diately, a message will be displayed.
The app will remain in the list and it will
be possible to reattempt downloading.
Canceling a download
–
Tap
Abort
to cancel a download in pro-
gress.
Note that only a download can be cancelled.
An installation cannot be cancelled once it has
begun.
Related information
•
•
•
•
•
Handling system updates via Download
Center (p. 586)
•
Hard disk storage space (p. 524)
Updating apps
Apps can be updated when the vehicle is
connected to the Internet.
Data downloading can affect other services
such as transfer data, e.g. web radio. If the
affect on other services is experienced as
problematic, the download can be interrup-
ted. Alternatively, it may be appropriate to
switch off or cancel other services.
When downloading using a phone, pay
extra attention to the data traffic costs.
If an app is being used while an update is in
progress, it will be restarted to complete the
update.
Update all
1. Open the
Download Center
app in App
view.
2. Select
Install all
.
> The update will begin.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
AUDIO, MEDIA AND INTERNET
* Option/accessory.
474
Update certain apps
1. Open the
Download Center
app in App
view.
2. Select
Application updates
to open a list
of all available updates.
3. Find the desired app and select
Install
.
> The update will begin.
Related information
•
•
•
•
Handling system updates via Download
Center (p. 586)
•
Deleting apps
When the vehicle is connected to the Inter-
net, it is possible to uninstall apps.
If the app is being used, it must be closed
before it can be uninstalled.
1. Open the
Download Center
app in App
view.
2. Select
Application updates
to open a list
of all installed apps.
3. Find the desired app and select
Uninstall
to begin uninstalling the app.
> When the app has been uninstalled, it
will be removed from the list.
Related information
•
•
•
•
Handling system updates via Download
Center (p. 586)
•
Radio
The radio can receive broadcasting from the
FM waveband with HD Radio
™
Technology
and SiriusXM
®
Satellite radio
*
. When the
vehicle has an Internet connection, it is also
possible to listen to web radio.
The radio can be controlled
using voice commands, the
right-side steering wheel key-
pad or the center display.
Related information
•
•
Changing waveband and radio station
(p. 476)
•
Storing radio channels in the Radio favor-
ites app (p. 477)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст