Volvo V60 Twin Engine (2020 year). Manual in english — page 16
||
KEY, LOCKS AND ALARM
* Option/accessory.
280
WARNING
Do not allow anyone to remain in the car
without first deactivating the function in
order to avoid the risk of anyone being
locked in.
Related information
•
•
Temporarily
*
deactivating double
locks
If someone is going to stay in the car but the
doors must be locked from the outside, then
the double lock function should be deacti-
vated, to allow unlocking from the inside.
WARNING
Do not allow anyone to remain in the car
without first deactivating the function in
order to avoid the risk of anyone being
locked in.
Press the
Reduced Guard
button in the centre display's
function view in order to
deactivate the double lock
function temporarily.
This also means that the alarm's movement
and tilt detectors
*
are switched off.
After this,
Reduced Guard
is shown in the
centre display and double locks are temporar-
ily deactivated in the subsequent locking of
the car.
In conventional locking, the electrical sockets
are deactivated immediately, but when double
locks are temporarily deactivated, they will be
active for a maximum of 10 minutes after lock-
ing.
If the car is unlocked and then locked again,
the double lock function must be deactivated
again.
The system is reset the next time the engine is
started.
Related information
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
282
Driving support systems
The car is equipped with different driver sup-
port systems which can assist the driver in
different situations, either actively or pas-
sively.
For example, the systems can help the driver
to:
•
maintain a set speed
•
maintain a certain time interval to the vehi-
cle ahead
•
prevent a collision by giving a warning to
the driver and braking the car
•
help the driver to park.
Some of the systems are fitted as standard
while others are options – which alternative
applies is market dependent.
Related information
•
IntelliSafe – driver support and safety
(p. 33)
•
Speed-dependent steering force (p. 282)
•
•
Electronic stability control (p. 283)
•
•
•
Automatic speed limiter (p. 295)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Steering assistance at risk of collision
(p. 384)
•
•
•
Speed-dependent steering force
Speed related power steering causes the
steering wheel force to increase with the
speed of the car so as to be able to give the
driver enhanced sensitivity.
On motorways the steering is firmer. When
parking and at low speed steering is light and
requires less effort.
In rare situations the power
steering may become too hot and
then needs to be temporarily
cooled – during this time the
power steering operates with reduced
power and turning the steering wheel may
then be perceived to be slightly heavier.
Then the message
Power steering
Assistance temporarily reduced
and this
symbol are shown in the driver display.
While the power steering is working at
reduced power, the driver support func-
tions and steering assistance system are
not available.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
283
WARNING
If the temperature increases too much, the
servo may be forced to switch off com-
pletely. In such a situation, the driver dis-
play shows the
Power steering failure
Stop safely
message, combined with a
symbol.
Change the steering force level
*
Steering wheel resistance can be adjusted
when using INDIVIDUAL drive mode.
1. Tap on
Settings
in the centre display's
top view.
2. Select
My Car
Drive Modes
Steering Force
.
Steering wheel resistance selection can only
be accessed if the car is stationary or is mov-
ing at low speed and in a straight line.
Related information
•
Driving support systems (p. 282)
•
Electronic stability control
Electronic Stability Control (ESC
1
) helps the
driver to avoid skidding and improves the
car's traction.
The driver display shows this
symbol when the system is
engaged.
Braking from the system may
be heard as a pulsing sound,
and the car may accelerate
more slowly than expected when applying the
throttle.
The system consists of the following subfunc-
tions:
•
Stability function
2
•
Spin control and traction control system
•
Engine Drag Control
•
Trailer stability assist
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Stability function
2
The function checks the driving and brake
force of the wheels individually in order to sta-
bilise the car.
1
Electronic Stability Control
2
Also known as Active Yaw Control.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
284
Spin control and traction control
system
The function is active at low speed and brakes
the drive wheels that spin so that additional
traction shall be transferred from the drive
wheels that are not spinning.
The function can also prevent the driving
wheels from spinning against the road surface
during acceleration.
Engine Drag Control
Engine Drag Control (EDC
3
) can prevent invol-
untary wheel locking, e.g. after shifting down
or engine braking when driving in low gear on
slippery road surfaces.
Involuntary wheel locking while driving can,
amongst other things, impair the driver's abil-
ity to steer the car.
Trailer stability assist
*
4
Trailer stability assist (TSA
5
) stabilises a car
towing a trailer in situations where they begin
snaking.
Trailer Stability Assist is deactivated if
ESC
Sport Mode
is activated.
Related information
•
Driving support systems (p. 282)
•
Activating or deactivating sport mode for
electronic stability control (p. 285)
•
Symbols and messages for electronic sta-
bility control (p. 286)
•
Electronic Stability Control in sport
mode
The stability system (ESC
6
) is always acti-
vated – it cannot be switched off. However,
the driver can select
ESC Sport Mode
,
which allows for a more active driving experi-
ence.
With the
ESC Sport Mode
subfunction
selected, intervention from the system is
reduced and the car is allowed to skid more
and greater control than normal is thus trans-
ferred to the driver.
When
ESC Sport Mode
is selected, the func-
tion can be considered as deactivated, despite
the function continuing to help the driver in
many cases.
With
ESC Sport Mode
selected, Trailer
Stability Assist (TSA
7
) is deactivated.
ESC Sport Mode
also provides more traction
even if the car has become bogged down or is
driving on a loose surface, such as in sand or
deep snow.
3
Engine Drag Control
4
Trailer stability assist is included when the Volvo genuine towbar is installed.
5
Trailer Stability Assist
6
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
285
Related information
•
Electronic stability control (p. 283)
•
Activating or deactivating sport mode for
electronic stability control (p. 285)
•
Activating or deactivating sport
mode for electronic stability
control
The stability system (ESC
8
) is always acti-
vated – it cannot be switched off. However,
the driver can select sport mode, which
allows for a more active driving experience.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – the function is
deactivated.
The driver display indicates activated
ESC Sport Mode
by displaying this
symbol with a constant glow until
the function is deactivated or the
engine is switched off. The next time the
engine is started, the system is back in its nor-
mal mode again.
The
ESC Sport Mode
function cannot be
selected when one of the following functions
is activated:
•
Speed limiter
•
Cruise control
•
Adaptive cruise control
*
•
Pilot Assist
*
Related information
•
Electronic Stability Control in sport mode
(p. 284)
•
Electronic stability control (p. 283)
7
Trailer Stability Assist
8
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
286
Symbols and messages for
electronic stability control
A number of symbols and messages regar-
ding electronic stability control (ESC
9
) can be
shown on the driver display. Here are some
examples.
Symbol Message
Specification
Constant glow for approx. 2 seconds. System check when the engine is started.
Flashing light.
The system is being activated.
Constant glow.
Sport mode is activated.
NOTE:
The system is not deactivated in this mode – it is partly
reduced.
ESC
Temporarily off
The system has been temporarily reduced due to excessive brake temperature - the function is
reactivated automatically when the brakes have cooled.
ESC
Service required
The system is disengaged. Stop the car in a safe place, switch off the engine and start it again.
A text message can be cleared by briefly
pressing the
button, located in the centre
of the steering wheel's right-hand keypad.
If a message remains: Contact a workshop –
an authorised Volvo workshop is recom-
mended.
Related information
•
Electronic stability control (p. 283)
9
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
287
Connected Safety
10
Connected Safety communicates information
between your own car and other vehicles via
the Internet
11
. The function is intended to
make a driver aware that there may be a
potentially dangerous traffic situation further
ahead on the same road.
The Connected Safety function can inform the
driver whether another vehicle further ahead
on the same road has activated its hazard
warning flashers or detected slippery driving
conditions. Information about slippery driving
conditions is also given if your own car detects
slippery surfaces.
Connected Safety can help the driver with the
following:
•
Alarm on hazard warning flashers
•
Alarm on slippery driving conditions
If slippery driving conditions are detected by
your own car - in addition to you the driver -
drivers in other vehicles will also be informed
about this via the Internet.
In vehicles with head-up display, the warning
symbols for Connected Safety are also shown
there.
Connected Safety communication
between vehicles only works for the vehi-
cles equipped with the function and have it
activated.
Alarm on hazard warning flashers
If your own car's hazard warning flashers are
activated, information about this can be sent
to vehicles approaching your own car's posi-
tion.
When your own car is
approaching a vehicle with
flashing hazard warning
flashers, this symbol is
shown on the instrument
panel.
When your own car is close to a vehicle with
flashing hazard warning flashers, the symbol
doubles in size.
Alarm on slippery driving conditions
If your own car detects a deterioration in fric-
tion between tyres and road surface, the infor-
mation is sent to the vehicles approaching the
position of your own car.
If an ice alert is triggered, this
symbol is displayed on the
instrument panel when a
vehicle approaches the slip-
pery road section, both in
your own car and in other
vehicles that have received
the information via Connected Safety.
When the approaching vehicle is close to the
slippery section of road, the symbol doubles in
size on the vehicle's instrument panel.
10
Not available on all markets.
11
Data is transferred (data traffic) when using the Internet, and this may involve a cost.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
288
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
Driving support systems (p. 282)
•
Activating or deactivating Connected
Safety (p. 288)
•
Limitations of Connected Safety (p. 289)
•
Activating or deactivating
Connected Safety
For Connected Safety to be able to share
information on road conditions with other
vehicles, the function needs to be activated.
The function can be deactivated if you do not
want to share information.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – the function is
deactivated.
When activated, several windows are shown
with terms and conditions that must be
accepted by the driver to enable connection to
the Internet
12
. For example, a situation where
the driver must accept data being sent from
the car using his/her mobile phone.
If there is no Internet connection, your own car
will still inform you, the driver, that slippery
driving conditions have been detected by your
own car. For Connected Safety to work opti-
mally, your own car needs to be connected to
the Internet.
Related information
•
•
•
User terms and conditions and data shar-
ing (p. 539)
•
Limitations of Connected Safety (p. 289)
12
Data is transferred (data traffic) when using the Internet, and this may involve a cost.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
289
Limitations of Connected Safety
Information about vehicles with activated
hazard warning flashers or which have
detected slippery driving conditions is not
always communicated between all vehicles
within the same area.
This can be because for example:
•
Poor or no contact with the Internet.
•
Vehicles on slippery surfaces make
manoeuvres that are too weak for friction
between tyres and road surface to be
detectable, e.g. steering wheel movement,
acceleration or braking.
•
Vehicles that have detected slippery surfa-
ces, or have activated their hazard warn-
ing flashers, do not have the function acti-
vated.
•
Vehicles that have detected slippery surfa-
ces, or have activated their hazard warn-
ing flashers, are not equipped with the
function.
•
There may be no warning due to missing
or defective global positioning/satellite
navigation.
•
Detection of slippery surfaces or activation
of hazard warning flashers has taken place
on a minor road which is missing in Volvo
Cars database.
•
Connected Safety is not available in all
markets and does not cover all areas - a
retailer for Volvo has information on cur-
rent areas.
WARNING
•
In certain situations, the function may
give incorrect warnings for slippery
driving conditions.
•
The function cannot always detect
other vehicles with activated hazard
warning flashers or detect all sections
of road with slippery surfaces.
Related information
•
•
Distance Warning
*
13
The Distance Warning function can assist the
driver to notice that the time interval to the
vehicle ahead may be too short. This requires
the car to be equipped with a head-up dis-
play
*
to be able to display Distance Warning.
Distance Warning symbol on the windscreen with
head-up display.
In cars equipped with head-up display, a sym-
bol is shown on the windscreen for as long as
the time interval to the vehicle ahead is shorter
than the preset value. However, this assumes
that the
Show Driver Support
function is
activated via the settings in the car's menu
system.
Distance warning is active at speeds
above 30 km/h (20 mph) and only reacts to
the vehicle ahead travelling in the same direc-
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
290
tion. No distance information is provided for
oncoming, slow or stationary vehicles.
Strong sunlight, reflections, extreme light
contrasts, the use of sunglasses, or if the
driver is not looking straight ahead may
make the visual warning signal in the wind-
screen difficult to recognise.
Distance warning is deactivated during the
time the adaptive cruise control
*
or Pilot
Assist
*
is active.
WARNING
Distance warning only reacts if the time
window to the vehicle ahead is shorter
than the preset value – the speed of the
driver's vehicle is not affected.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
•
Activating or deactivating distance warn-
ing (p. 291)
•
Limitations of Distance Warning (p. 291)
•
Set time interval to vehicle ahead (p. 323)
•
Warning from driver support in the event
of a collision risk (p. 320)
•
13
Distance Alert
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
291
Activating or deactivating distance
warning
14
The distance warning function can be deacti-
vated. The function is only available in cars
that can show information on the windscreen
with a so-called head-up display
*
.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – the function is
deactivated.
Distance Warning is activated automatically
each time the engine is started.
Related information
•
•
Limitations of Distance Warning (p. 291)
Limitations of Distance Warning
15
The distance warning function may have limi-
tations in certain situations. The function is
only available in cars that can show informa-
tion on the windscreen with a so-called head-
up display
*
.
WARNING
•
A vehicle's size may affect the ability to
be detected, e.g. motorcycles, which
could mean that the warning lamp illu-
minates at a shorter time window than
set or that the warning is temporarily
absent.
•
Extremely high speeds can cause the
lamp to illuminate at a shorter time
window than that set due to limitations
in radar unit range.
This function uses the car's camera and
radar units, which have certain general lim-
itations.
Related information
•
•
Limitations for camera and radar unit
(p. 339)
•
14
Distance Alert
15
Distance Alert
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
292
Speed limiter
A speed limiter (SL
16
) can be likened to a
reverse cruise control - the driver regulates
the speed using the accelerator pedal but is
prevented from accidentally exceeding a pre-
selected/set maximum speed by the speed
limiter.
Buttons and symbols for the function.
: Activates the speed limiter from
standby mode and resumes stored maxi-
mum speed
: Increases the stored maximum
speed
:
From standby mode
– activates the
speed limiter and stores current speed
:
From active mode
– deactivates/
changes the speed limiter to standby
mode
: Reduces stored maximum speed
Marker for stored max speed
The car's current speed
Stored maximum speed
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
Driving support systems (p. 282)
•
Limitations for speed limiter (p. 295)
•
Selecting and activating speed limiter
(p. 293)
•
Deactivating the speed limiter (p. 294)
16
Speed Limiter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
293
•
Temporary deactivation of speed limiter
(p. 294)
•
Set the stored speed for driver support
(p. 322)
•
Automatic speed limiter (p. 295)
Selecting and activating speed
limiter
The speed limiter function (SL
17
) must first be
selected and activated in order to be able to
regulate the speed.
The speed limiter cannot be activated until
after the engine has been started. The lowest
maximum speed that can be stored is
30 km/h (20 mph).
1. Press
◀
(1) or
▶
(3) to scroll to the symbol
for the speed limiter
(4).
> The symbol is grey – the speed limiter
is in standby mode.
2. When speed limiter is selected – press the
steering wheel button
(2) to activate.
> The symbol is white – the speed limiter
is started and the current speed is
stored as maximum speed.
Related information
•
•
Deactivating the speed limiter (p. 294)
•
Temporary deactivation of speed limiter
(p. 294)
17
Speed Limiter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
294
Deactivating the speed limiter
The speed limiter (SL
18
) can be deactivated
and switched off.
1. Press the steering wheel button
(2).
> The symbol and indicators turn grey –
the speed limiter is set in standby mode
and the driver can exceed the set speed
limit.
2. Press the steering wheel button
◀
(1) or
▶
(3) to change to another function.
> The driver display's symbol and indica-
tor for speed limiter (4) are switched off
– which deletes the stored maximum
speed.
Related information
•
•
Selecting and activating speed limiter
(p. 293)
•
Temporary deactivation of speed limiter
(p. 294)
Temporary deactivation of speed
limiter
The speed limiter (SL
19
) can be temporarily
deactivated and set in standby mode.
Temporary deactivation with the
accelerator pedal
The speed limiter can also be temporarily
deactivated and overridden with the accelera-
tor pedal without the speed limiter first having
to be set in standby mode - e.g. to be able to
quickly accelerate the car out of a situation.
In which case, proceed as follows:
1. Fully depress the accelerator pedal and
release it to interrupt acceleration when
the desired speed has been reached.
> In this mode, the speed limiter is still
activated and the driver display's sym-
bol is therefore WHITE.
2. Fully release the accelerator pedal when
the temporary acceleration is finished.
> The car is then engine-braked automat-
ically to below the last stored maximum
speed.
18
Speed Limiter
19
Speed Limiter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
295
Related information
•
•
Selecting and activating speed limiter
(p. 293)
•
Deactivating the speed limiter (p. 294)
Limitations for speed limiter
Speed limiter (SL
20
) has certain general limi-
tations.
On steep downhill gradients the speed limit-
er’s (SL
21
) braking effect may be inadequate
and hence the stored maximum speed may be
exceeded. In this case, the driver is alerted by
the message
Speed limit exceeded
in the
driver display.
A text message that the maximum speed is
exceeded will be activated if the speed has
been exceeded by at least 3 km/h
(approx. 2 mph).
Related information
•
Automatic speed limiter
The Automatic Speed Limiter (ASL
22
) func-
tion helps the driver to adapt the car's maxi-
mum speed to the speed shown on the road
signs.
The Speed Limiter function (SL
23
) can be
changed to Automatic Speed Limiter (ASL).
The automatic speed limiter uses speed infor-
mation from the Road Sign Information
*
(RSI
24
) function to automatically adapt the
car's maximum speed.
WARNING
Even if the driver clearly sees the speed-
related road sign, the speed information
from the Road Sign Information
*
(RSI)
function to ASL may be incorrect – in such
cases the driver must intervene him/herself
and accelerate or brake to a suitable speed.
20
Speed Limiter
21
Speed Limiter
22
Automatic Speed Limiter
23
Speed Limiter
24
Road Sign Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
296
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Is SL or ASL active?
Symbols in the driver display show which
speed limiter function is active:
Symbol
SL ASL
A
✓
✓
Sign symbol after "70" = ASL is
activated.
✓
A
WHITE symbol: Function active, GREY symbol: Standby
mode.
The ASL symbol
The sign symbol (displayed along-
side the stored speed, "70", in the
centre of the speedometer) can be
shown in three colours with the fol-
lowing meanings:
Colour of
sign symbol
Meaning
Greenish yel-
low
ASL is active
Grey
ASL has been set in
standby mode
Orange
ASL is in temporary
standby mode - e.g. due to
a traffic sign not being
read
Related information
•
Driving support systems (p. 282)
•
Activating or deactivating the automatic
speed limiter (p. 297)
•
Changing the tolerance for the automatic
speed limiter (p. 298)
•
Limitations for automatic speed limiter
(p. 298)
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст