Volvo S60 Inscription (2016 year). Instruction — part 11
07 Driver support
07
184
Collision warning – troubleshooting
Fault tracing and actions
If the message
Windscreen Sensors
blocked
is displayed, this means that the
camera is obscured and cannot detect
pedestrians, cyclists, vehicles or road marker
lines in front of the vehicle.
This, in turn, means that Pedestrian and
Cyclist Detection with Full Auto Brake, Driver
Alert Control, Lane Departure Warning or
Lane Keeping Aid will not have full functional-
ity.
The table lists possible causes for this mes-
sage being displayed, and suitable actions.
Cause
Action
The surface of the windshield in front of the camera is dirty or covered
with ice or snow.
Clean or clear the section of the windshield in front of the camera.
Fog, heavy rain or snow is interfering with the function of the camera.
No action possible. Heavy precipitation may affect the function of the
camera.
The surface of the windshield is clean but the message remains in the
display.
Wait a short time. It may take several minutes for the camera to regis-
ter visibility.
The surface between the inside of the windshield and the camera is
dirty.
Contact an authorized Volvo retailer or service technician to have this
surface cleaned.
07 Driver support
07
*
Option/accessory, for more information, see Introduction.
185
Maintenance
Camera and radar sensor
5
.
In order to function properly, the camera and
radar sensor must be kept clean. Dirt, ice,
snow, etc., will reduce the function of these
components.
Remove ice and snow when necessary and
wash these areas regularly with a suitable car
washing liquid.
Related information
•
Collision warning – introduction (p. 175)
•
Collision warning* – function (p. 177)
•
Collision warning* – operation (p. 178)
•
Collision warning* – Pedestrian detection
•
Collision warning* – Cyclist detection
•
Collision warning* – limitations (p. 181)
•
The camera’s limitations (p. 183)
•
Collision warning – symbols and mes-
5
The illustration is generic; details will vary, depending on the model
07 Driver support
07
186
Collision warning – symbols and
messages
The table lists possible causes for collision
warning-related messages being displayed,
and suitable actions.
A text message can be erased by pressing
briefly on the OK button on the turn signal
lever.
Symbol Message
Description
Collis'n warning
OFF
Pedestrian and Cyclist Detection with Full Auto Brake is switched off. This message is displayed when the
engine is started and will disappear after approx. 5 seconds. It can also be erased by pressing the OK but-
ton.
Collision Warning
Unavailable
Pedestrian and Cyclist Detection with Full Auto Brake cannot be activated. This message is displayed when
the driver attempts to activate the function. It will disappear after approx. 5 seconds or can be erased by
pressing the OK button.
Auto braking was
activated
Auto-braking has been active. This message can be erased by pressing the OK button.
Windscreen Sen-
sors blocked
The camera is temporarily not functioning. This message is displayed if the camera is obstructed by snow,
limitations (p. 183) for more information on the camera’s limitations.
Radar blocked See
manual
Pedestrian and Cyclist Detection with Full Auto Brake is temporarily not functioning. The radar sensor is
blocked, for example by heavy rain or snow that has accumulated in front of the sensor, and cannot detect
other vehicles, see Adaptive Cruise Control – limitations (p. 159) for more information on the radar sensor’s
limitations.
Collision warn.
Service required
Pedestrian and Cyclist Detection with Full Auto Brake is partially or completely not functioning.
Contact a trained and qualified Volvo service technician if the message remains in the display.
07 Driver support
07
*
Option/accessory, for more information, see Introduction.
187
Related information
•
Collision warning – introduction (p. 175)
•
Collision warning* – function (p. 177)
•
Collision warning* – operation (p. 178)
•
Collision warning* – Pedestrian detection
•
Collision warning* – Cyclist detection
•
Collision warning* – limitations (p. 181)
•
07 Driver support
07
188
Driver Alert System
The Driver Alert System is designed to help a
driver who may be becoming fatigued or who
is inadvertently leaving the lane.
Introduction
The Driver Alert System consists of two differ-
ent functions that can be switched on
together or separately.
•
Driver Alert Control (DAC), see Driver
Alert Control (DAC) – introduction
•
Lane Departure Warning (LDW), see
Lane Departure Warning (LDW) – intro-
When one or both of the functions has been
switched on, it is in standby mode and is acti-
vated when the vehicle exceeds a speed of
40 mph (65 km/h).
The function deactivates if the vehicle's
speed goes under 37 mph (60 km/h).
Both functions use a camera that is depend-
ent on the road/lane being clearly marked by
painted lines on each side.
WARNING
The Driver Alert System does not function
in all situations and is designed to be a
supplementary aid. It is not, however,
intended to replace the driver’s attention
and judgement.
Driver Alert Control (DAC) –
introduction
DAC is intended to alert the driver if his/her
driving becomes erratic, such as if the driver
is distracted or fatigued.
DAC is designed to help detect a slowly
changing driving pattern. It is primarily
intended to be used on main roads and is not
meant for use in city traffic.
A camera monitors the painted lines marking
the lane in which the vehicle is traveling and
compares the direction of the road with the
driver’s movements of the steering wheel.
The driver is alerted if the vehicle does not
follow the lane smoothly.
The camera has certain limitations, see
Adaptive Cruise Control – limitations
WARNING
•
DAC is not intended to extend the
duration of driving. Always plan breaks
at regular intervals to help remain alert.
•
A warning from DAC should not be
ignored. A driver may not be aware of
how fatigued he/she has become.
•
In certain cases, fatigue may not affect
the driver’s behavior. In situations of
this type, no warning will be provided.
Therefore, it is important to take
breaks at regular intervals, regardless
of whether or not DAC has given a
warning.
Related information
•
Driver Alert Control (DAC) – function
•
Driver Alert Control (DAC) – operation
•
Driver Alert Control (DAC) – limitations
•
07 Driver support
07
}}
189
•
•
Lane Departure Warning (LDW) – intro-
Driver Alert Control (DAC) – operation
Operating DAC
Settings are made using menu system and
the display in the center console. See My Car
– introduction (p. 66) for more information on
the menu system.
On/Off
To put Driver Alert in standby mode:
•
In the MY CAR menu, scroll to
Car
settings
Driver support systems
Driver Alert
and check the box. If the box
is not checked, the function is off.
Related information
•
Driver Alert Control (DAC) – introduction
•
Driver Alert Control (DAC) – function
•
Driver Alert Control (DAC) – limitations
•
Driver Alert Control (DAC) – symbols and
•
Driver Alert Control (DAC) – introduction
•
Lane Departure Warning (LDW) – intro-
Driver Alert Control (DAC) – function
Function
Driver Alert is activated when the vehicle
exceeds a speed of 40 mph (65 km/h) and will
remain active as long as the speed is over
approx. 37 mph (60 km/h).
If the vehicle is being driven errati-
cally, the driver will be alerted by an
audible signal and the message
Driver Alert Time for a break
is
displayed. The warning will be repeated after
a short time if the driving pattern remains the
same.
Press the OK button to erase a message.
WARNING
•
An alert should be taken seriously
since it is sometimes difficult for a
driver to realize that he/she is fatigued.
•
In the event of a warning or if the
driver feels fatigued, stop as soon as
possible in a safe place and rest.
Related information
•
Driver Alert Control (DAC) – introduction
•
Driver Alert Control (DAC) – operation
•
07 Driver support
07
190
•
Driver Alert Control (DAC) – symbols and
•
•
Lane Departure Warning (LDW) – intro-
Driver Alert Control (DAC) –
limitations
Limitations
In certain situations, DAC may provide warn-
ings even if the driver’s driving pattern has
not become erratic:
•
in strong crosswinds
•
on grooved road surfaces.
•
if the driver is testing the LDW function,
see Lane Departure Warning (LDW) –
Related information
•
Driver Alert Control (DAC) – introduction
•
Driver Alert Control (DAC) – function
•
Driver Alert Control (DAC) – operation
•
Driver Alert Control (DAC) – symbols and
•
•
07 Driver support
07
}}
191
Driver Alert Control (DAC) – symbols
and messages
Depending on the situation, DAC may display
certain symbols and text messages in the
instrument panel or center console screen.
Symbols and messages
Instrument panel
Symbol Message
Description
Driver Alert Time for a
break
The vehicle has been driven erratically. The driver receives an audible signal and a text message.
Windscreen Sensors
blocked
The camera is temporarily not functioning, due to snow, ice, or dirt on the windshield. Clean the area of
the windshield in front of the camera. See The camera’s limitations (p. 183) for information on the cam-
era’s limitations.
Driver Alert Sys Service
required
The system is not functioning. Contact a trained and qualified Volvo service technician if the message
remains in the display.
||
07 Driver support
07
192
Center console display
Symbol Message
Description
-
Driver Alert OFF
The function is not switched on.
-
Driver Alert
Available
The function is active.
-
Driver Alert Standby <65
km/h
The function has gone into standby mode because the vehicle's speed is below 40 mph (65 km/h).
-
Driver Alert Unavailable
The camera is temporarily not functioning, due to snow, ice, or dirt on the windshield. Clean the area
of the windshield in front of the camera. See The camera’s limitations (p. 183) for information on the
camera’s limitations.
Related information
•
Driver Alert Control (DAC) – introduction
•
Driver Alert Control (DAC) – function
•
Driver Alert Control (DAC) – operation
•
Driver Alert Control (DAC) – limitations
•
•
07 Driver support
07
}}
193
Lane Departure Warning (LDW) –
introduction
The LDW function is designed to help reduce
the risk of accidents in situations where the
vehicle unintentionally leaves its lane and
there is a risk of driving off the road or into the
opposite lane.
Lane Departure Warning (LDW)
The illustration is generic
LDW uses the camera located at the center,
upper edge of the windshield to monitor the
road's/lane’s side marker lines. If the vehicle
crosses a side marker line or the road’s cen-
ter dividing line, the driver will be alerted by
an audible signal.
WARNING
This feature is only intended to assist the
driver and does not function in all driving,
weather, traffic or road conditions.
As the driver, you have full responsibility
for operating the vehicle in a safe manner.
Related information
•
•
Lane Departure Warning (LDW) – symbols
•
Lane Departure Warning (LDW) – opera-
•
Lane Departure Warning (LDW) - limita-
Lane Departure Warning (LDW) –
operation
Operation and function
LDW can be switched on or off by pressing
the button on the center console. A light in
the button illuminates when the function is
on. This is supplemented by graphic displays
in the instrument panel, for example:
||
07 Driver support
07
194
LDW displayed in the instrument panel
•
The LDW symbol has white side marker
lines: – the function is active and "sees"
one or both of the road's side marker
lines.
•
The LDW symbol has gray side marker
lines: – the function is active but cannot
"see" one or both of the road's side
marker lines.
or
•
The LDW symbol has gray side marker
lines: – the function is in standby mode
because the vehicle's speed is below
40 mph (65 km/h).
•
The LDW symbol has no side marker
lines: – the function is deactivated.
WARNING
The driver will only be warned once for
each time the wheels cross a marker line.
No alarm will be given if a marker line is
between the wheels.
Settings
Settings for Lane Departure Warning can be
made in the menu system by pressing My
Car. Go to
Settings
Car settings
Driver support systems
Lane Departure
Warning
.
There are two alternatives:
•
On at start-up
: This selection switches
LDW on each time the engine is started.
Otherwise, the system will be in the mode
that it was in when the engine was
switched off.
•
Increased sensitivity
: This selection
increases the function’s sensitivity. Warn-
ings will be given at an earlier stage and
fewer limitations apply. When this setting
is being used, the system only needs to
monitor lane marker lines on one side of
the vehicle to change status to
Lane
Depart Warn Available
.
Related information
•
•
Lane Departure Warning (LDW) – symbols
•
Lane Departure Warning (LDW) – intro-
•
07 Driver support
07
195
Lane Departure Warning (LDW) -
limitations
Limitations
The camera used by LDW has the same limi-
tations as the human eye. See The camera’s
limitations (p. 183) for more information about
the camera's limitations.
No warning signal will be given in the cer-
tain situations, such as:
•
If the turn signal is being used
•
The driver’s foot is on the brake pedal
6
•
The accelerator pedal is pressed
quickly
6
•
If the steering wheel is moved quickly
6
•
In sharp turns that cause the vehicle’s
body to sway
Related information
•
•
Lane Departure Warning (LDW) – symbols
•
Lane Departure Warning (LDW) – opera-
•
Lane Departure Warning (LDW) – intro-
6
When Increased sensitivity has been selected, a warning will be issued if a side marker line is crossed in this situation.
07 Driver support
07
196
Lane Departure Warning (LDW) –
symbols and messages
Symbols and messages
A text message can be erased by pressing
briefly on the OK button on the turn signal
lever.
Symbol Message
Description
Lane departure warning ON
/
Lane departure warning OFF
The function is switched on or off. The text disappears after 5 seconds.
-
Lane Depart Warn Available
The function is monitoring the road’s marker lines.
-
Lane Depart. Warning
Unavailable at this speed
The function has gone into standby mode because the vehicle's speed is below 40 mph
(65 km/h).
-
Lane Depart Warn Unavaila-
ble
The road lacks clear marker lines or the camera is not functioning properly. See The camera’s
limitations (p. 183) for information on the camera’s limitations.
Windscreen Sensors blocked
The camera is temporarily not functioning, due to snow, ice, or dirt on the windshield. Clean the
area of the windshield in front of the camera. See The camera’s limitations (p. 183) for information
on the camera’s limitations.
Driver Alert Sys Service
required
The system is not functioning. Contact a trained and qualified Volvo service technician if the mes-
sage remains in the display.
07 Driver support
07
197
Related information
•
Lane Departure Warning (LDW) – opera-
•
•
Lane Departure Warning (LDW) – intro-
•
07 Driver support
07
198
Park assist – introduction
The park assist system is designed to assist
you when driving into parking spaces,
garages, etc. An audible signal and symbols
in the audio system’s display indicate the dis-
tance to the object.
The park assist system utilizes ultrasound
sensors in the front bumper and rear
bumper(s) to measure the distance to a vehi-
cle or an object that may be close to the front
or rear of your vehicle.
A trailer hitch whose wiring is integrated
with the vehicle's electrical system will be
included in the measurement of the availa-
ble space behind the vehicle.
WARNING
Park Assist is an information system, NOT
a safety system. This system is designed
to be a supplementary aid when parking
the vehicle. It is not, however, intended to
replace the driver's attention and judge-
ment.
Related information
•
Park assist – limitations (p. 200)
•
Park assist – function (p. 198)
•
Park assist – operation (p. 200)
•
Park assist – troubleshooting (p. 201)
•
Rear Park Assist Camera (PAC) – function
Park assist – function
Signals from the park assist system
View in the display (warning for objects front left/
right rear)
Visual indicator
The audio system’s display gives an overview
of the vehicle’s position in relation to a
detected object.
The marked sectors in the display indicate
that one or more of the sensors has detected
an object. The closer the car symbol comes
to a sector, the closer the vehicle is to the
object.
If the infotainment system is switched off, the
park assist system will not be able to provide
a visual indicator. An audible signal will still
be provided.
07 Driver support
07
199
Audible signal
The Park Assist system uses an intermittent
tone that pulses faster as you come close to
an object, and becomes constant when you
are within approximately 1 ft (30 cm) of an
object in front of or behind the vehicle. If
there are objects within this distance both
behind and in front of the vehicle, the tone
alternates between front and rear speakers.
The level of the audible signal can be low-
ered/raised with the infotainment volume
control. The level can also be set in the MY
CAR menu system. See My Car – introduc-
tion (p. 66) for a description of the menu
system.
If the volume of another source from the
audio system is high, this will be automati-
cally lowered.
Rear park assist
The distance monitored behind the vehicle is
approximately 5 ft (1.5 m). The audible signal
comes from the rear speakers.
The system must be deactivated when towing
a trailer, carrying bicycles in a rear-mounted
carrier, etc, which could trigger the rear park
assist system's sensors.
•
Rear park assist is deactivated auto-
matically when towing a trailer if Volvo
genuine trailer wiring is used. If a non-
Volvo trailer hitch is being used, it may
be necessary to switch off the system
manually, see Park assist – operation
•
The system will not detect high
objects, such as a loading dock, etc.
•
Objects such as chains, thin shiny
poles or low objects may temporarily
not be detected by the system. This
may result in the pulsing tone unex-
pectedly stopping instead of changing
to a constant tone as the vehicle
approaches the object. In such cases,
use caution when backing up or stop
the vehicle to help avoid damage.
Front park assist
The distance monitored in front of the vehicle
is approximately 2.5 ft (0.8 m). The audible
signal comes from the audio system's front
speakers.
It may not be possible to combine auxiliary
headlights and front park assist since these
lights could trigger the system's sensors.
Front park assist is deactivated when the
parking brake is applied and or when the
gear selector is in the P position.
Related information
•
Park assist – introduction (p. 198)
•
Park assist – limitations (p. 200)
•
Park assist – operation (p. 200)
•
Park assist – troubleshooting (p. 201)
•
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст