Volvo S60 Recharge Plug-in Hybrid (2021 year). Manual in english — page 10
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
175
Wiper blades and washer fluid
The wipers and the washer fluid are designed
to improve visibility and the headlight pat-
tern.
Washer fluid direct from the wiper blades and
heating
*
of the wiper blades gives improved
vision.
When there is approximately 1 liter (1 qt) of
washer fluid remaining, a message to refill will
appear in the instrument panel.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight wash-
ers (p. 177)
•
Activating and deactivating the rain sen-
sor's memory function (p. 177)
•
•
Putting the wiper blades in service posi-
tion (p. 630)
•
Replacing windshield wiper blades
(p. 629)
•
Using the windshield wipers (p. 175)
Using the windshield wipers
The windshield wipers are designed to clean
the windshield. The right-side steering wheel
lever is used to adjust windshield wiper set-
tings.
Right-hand steering wheel lever.
The thumb wheel is used to set rain sen-
sor sensitivity and interval wiper speed.
Single sweep
Move the lever down and release for a
single sweep.
Wipers off
Move the lever to position
0
to turn off
the windshield wipers.
Interval wipers
Move the lever upward to put the wip-
ers in interval wiping mode. Set the
number of sweeps per time unit with the
thumb wheel when interval wipers are
selected.
Continuous wipers
Move the lever upward for the wipers
to operate at normal speed.
Move the lever upward again for the
wipers to operate at high speed.
Before activating the wipers, make sure
that the wiper blades are not frozen in
place and that any snow or ice on the
windshield has been scraped away.
Use plenty of washer fluid when the wipers
clean the windshield. The windshield must
be wet when the windshield wipers are
working.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight wash-
ers (p. 177)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
176
•
Activating and deactivating the rain sen-
sor's memory function (p. 177)
•
•
Putting the wiper blades in service posi-
tion (p. 630)
•
Replacing windshield wiper blades
(p. 629)
Using the rain sensor
The rain sensor monitors the amount of water
on the windshield and automatically starts
the windshield wipers. Rain sensor sensitivity
can be adjusted using the thumb wheel on
the right-hand steering wheel lever.
Right-hand steering wheel lever.
Rain sensor button
Thumb wheel, sensitivity/interval wiper
speed
When the rain sensor is activated, the
rain sensor symbol will be displayed in the
instrument panel.
Activating the rain sensor
When the rain sensor is activated, the engine
must be running or the ignition in mode
I
or
II
while the windshield wiper lever is in position
0
or in the single sweep position.
Activate the rain sensor by pressing the rain
sensor button
.
Move the lever downward for an extra wiper
sweep.
Turn the thumb wheel upward for increased
sensitivity and downward for decreased sensi-
tivity. The wipers will make one extra sweep
when the thumb wheel is turned upward.
Deactivate the rain sensor
Deactivate the rain sensor by pressing the
rain sensor button or moving the lever
upward to another wiper mode.
The rain sensor is automatically deactivated in
ignition mode
0
or when the engine is
switched off.
The rain sensor is also automatically deacti-
vated when the wiper blades are put in the
service position. The rain sensor will reactivate
when service mode is switched off.
The windshield wipers may start inadver-
tently and be damaged in automatic car
washes. Deactivate the rain sensor when
the engine is running or when the ignition
is in mode
I
or
II
. The symbol in the instru-
ment panel will go out.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WINDOWS, GLASS AND MIRRORS
}}
177
Related information
•
Using the windshield and headlight wash-
ers (p. 177)
•
Wiper blades and washer fluid (p. 175)
•
Activating and deactivating the rain sen-
sor's memory function (p. 177)
•
•
Putting the wiper blades in service posi-
tion (p. 630)
•
Replacing windshield wiper blades
(p. 629)
•
Using the windshield wipers (p. 175)
Activating and deactivating the
rain sensor's memory function
The rain sensor monitors the amount of water
on the windshield and automatically starts
the windshield wipers.
When the memory function is activated, the
rain sensor button does not need to be
pressed every time the vehicle is started:
1. Tap
Settings
in the center display's Top
view.
2. Tap
My Car
Wipers
.
3. Select
Rain Sensor Memory
to activate/
deactivate the memory function.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight wash-
ers (p. 177)
•
Wiper blades and washer fluid (p. 175)
•
•
Putting the wiper blades in service posi-
tion (p. 630)
•
Replacing windshield wiper blades
(p. 629)
•
Using the windshield wipers (p. 175)
Using the windshield and
headlight washers
The windshield and headlight washers are
designed to clean the windshield and head-
lights. Use the right-side steering wheel lever
to start the windshield and headlight wash-
ers.
Starting the windshield and headlight
washers
Washing function, right-hand steering wheel lever.
–
Move the right-hand steering wheel lever
toward the steering wheel to start the
windshield and headlight washers.
> After the lever is released, the wipers
make several extra sweeps.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
178
Avoid activating the washer system when
it is frozen or the fluid reservoir is empty.
Otherwise, there is a risk of damaging the
pump.
Headlight washer
*
To save washer fluid, the headlights are
washed automatically according to a defined
interval when the headlights are on.
Reduced washing
When there is about 1 liter (1 qt) of washer
fluid left in the reservoir and the
Washer fluid
Level low, refill
message is displayed in the
instrument panel together with the
sym-
bol, the washer fluid supply to the headlights
is cut off. This is to prioritize windshield clean-
ing and visibility through it. The headlights are
only washed if high or low beam is on.
Related information
•
Using the rain sensor (p. 176)
•
Wiper blades and washer fluid (p. 175)
•
Activating and deactivating the rain sen-
sor's memory function (p. 177)
•
•
Putting the wiper blades in service posi-
tion (p. 630)
•
Replacing windshield wiper blades
(p. 629)
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
180
Manual front seats
The front seats can be adjusted in a number
of different ways to help enhance your seat-
ing comfort.
Raise/lower the front edge of the seat
cushion
*
by moving the control up/down.
1
Change the length of the seat cushion
*
by
pulling up the lever and moving the cush-
ion forward/backward.
Move the seat forward/backing by lifting
the handle and moving the seat to a suita-
ble distance from the steering wheel and
pedals. Check to make sure the seat is
securely locked into place after its setting
has been changed.
Adjust lumbar support
*
by pressing the
button up/down/forward/rearward.
2
Raise/lower the seat by moving the con-
trol up/down.
Change the backrest tilt by turning the
knob on the backrest.
WARNING
•
Do not adjust the seat while driving.
The seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•
Check that the seat is securely locked
into position after adjusting.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
1
Only applies to the driver's seat.
2
Applies for four-way lumbar support
*
. Two-way lumbar support
*
is adjusted forward/rearward.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
181
Power
*
front seats
The front seats can be adjusted in a number
of different ways to help enhance your seat-
ing comfort. The power seat can be moved
forward/backward and up/down. The height
and length
*
of the seat cushion and the tilt of
the backrest can be adjusted. Lumbar sup-
port
*
can be adjusted up, down, forward and
backward.
3
The seats can be adjusted when the engine is
running and for a certain period of time after
the door has been unlocked without the
engine running. They can also be adjusted for
a short period after the engine is turned off.
The power seats have an overload protec-
tor that is triggered if a seat is blocked by
any object. If this occurs, remove the
object and attempt to adjust the seat
again.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Adjusting the power
*
front seats
Set the desired seating position using the
controls on the front seat cushion. To set the
convenience functions, turn the multifunction
control
4
upward/downward.
The illustration shows the controls in a vehicle with
four-way lumbar support
*
. Vehicles with two-way
lumbar support
*
do not have the rotary multifunction
control.
In vehicles with four-way lumbar support
*
,
turn the multifunction control
4
up/down to
set the convenience functions. In vehicles
with two-way lumbar support
*
, use the
round button to adjust the lumbar support
forward/rearward.
Raise/lower the front edge of the seat
cushion by moving the control up/down.
3
Applies for four-way lumbar support
*
. Two-way lumbar support
*
is adjusted forward/rearward.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
SEATS AND STEERING WHEEL
* Option/accessory.
182
Raise/lower the seat by moving the con-
trol up/down.
Move the seat forward/rearward by mov-
ing the control forward/rearward.
Change the backrest tilt by moving the
control forward/backward.
Only one movement (forward/rearward/up/
down) can be performed at a time.
The front seat backrests cannot be folded
down completely.
Related information
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Storing positions for seats, mirrors
and head-up display
*
Adjustment settings for the power
*
seat, door
mirrors and head-up display
*
can be stored in
the memory buttons.
Two different positions for the power
*
seat,
door mirrors and head-up display
*
can be
stored using the memory buttons. The buttons
are located on the inside of either one or both
*
front doors.
Button
M
for storing a setting.
Memory button.
Memory button.
4
Not available in vehicles with two-way lumbar support
*
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
183
Storing positions
1. Adjust the seat, door mirrors and head-up
display to the desired position.
2. Press and hold the
M
button. The indica-
tor light in the button will illuminate.
3. Within three seconds, press and hold the
1
or
2
button.
> When the position has been stored in
the memory button, an audio signal will
sound and the indicator light in the
M
button will go out.
If none of the memory buttons are pressed
within three seconds, the
M
button will go out
and no position will be stored.
The seats, door mirrors or head-up display
must be readjusted before a new memory
position can be set.
For the stored positions to work, all driver
profiles need to be in
Protect Profile
mode.
Related information
•
•
•
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
•
Adjusting the door mirrors (p. 169)
•
•
Protecting a driver profile (p. 136)
Using stored positions for seats,
mirrors and head-up display
*
If the positions for the power
*
seat, door mir-
rors and head-up display
*
have been stored,
they can be activated using the memory but-
tons.
Using a stored position
A stored position can be used with the front
door open or closed:
Front door open
–
Briefly press one of the memory buttons
1
(
) or
2
(
). The power seats, door mir-
rors and head-up display will move and
stop at the positions stored in that button.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
SEATS AND STEERING WHEEL
* Option/accessory.
184
Front door closed
–
Press and hold one of the memory buttons
1
(
) or
2
(
) until the seat, door mirrors
and head-up display stop in the positions
stored in that memory button.
If the memory button is released, the seat,
door mirrors and head-up display will stop
moving.
WARNING
•
This list point needs to be translated
exactly to: "Because the driver's seat
can be adjusted with the ignition off,
children should never be left unatten-
ded in the vehicle.
•
Movement of the seat can be STOP-
PED at any time by pressing any but-
ton on the power seat control panel.
•
Do not adjust the seat while driving.
•
The seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•
The seat rails on the floor must not be
obstructed in any way when the seat is
in motion.
For the stored positions to work, all driver
profiles need to be in
Protect Profile
mode.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
•
Adjusting the door mirrors (p. 169)
•
Front seat massage
*
settings
The settings for the multifunctional seats can
be adjusted using either the mutifunction
control on the side of the seat or the center
display. The adjustment settings are shown in
the center display.
Multifunction control, located on the side of the seat
cushion.
Massage settings
The following massage settings are available:
•
On
/
Off
: Select
On
/
Off
to turn on/off the
massage function.
•
Programs 1-5
: There are 5 preset mas-
sage programs. Select
Swell
,
Tread
,
Advanced
,
Lumbar
or
Shoulder
.
•
Intensity
: Select
Low
,
Normal
or
High
.
•
Speed
: Select
Slow
,
Normal
or
Fast
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
185
Restarting the massage function
The massage function turns off automatically
after 20 minutes. The function is reactivated
manually.
–
Tap
Restart
, which is displayed in the
center display, to restart the selected mas-
sage program.
> The massage program will restart. If no
selection is made, the message will be
stored in Top view.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Adjusting front seat massage
settings
*
The settings for the multifunctional seats can
be adjusted using either the mutifunction
control on the seat or the center display. The
adjustment settings are shown in the center
display.
Adjusting front seat massage settings
The front seat backrests have a massage func-
tion. Air-filled cushions provide the massaging
action and a number of settings are available.
The massage function can only be activated
when the engine is running.
1. Activate the multifunction control by turn-
ing the control
upward/downward. The
seat settings view will appear in the center
display.
2. Select
Massage
in the seat settings view.
3. Select massage settings by tapping the
center display or by moving the cursor up/
down using the multifunction control's
upper
/lower
buttons. Change a set-
ting in the selected function by tapping
the arrows on the center display or by
using the multifunction control's front
/
rear
buttons.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
186
Adjusting
*
front seat cushion
length
Depending on the selected equipment level,
the length of the seat cushion can either be
adjusted using the multifunction control
*
on
the side of the seat cushion, or manually
adjusted using the control on the front of the
seat cushion.
Adjusting seat cushion length using
the multifunction control
The multifunction control, located on the side of the
seat cushion.
1. Activate the multifunction control by turn-
ing the control
upward/downward. The
seat settings view will appear in the center
display.
2. Select
Cushion extension
in the seat set-
tings view.
•
Push in the front part of the four-way
button
to extend the seat cushion.
•
Press the rear part of the four-way but-
ton
to shorten the seat cushion.
Manually adjusting seat cushion
length
Control for adjusting seat cushion.
1. Grasp the
handle on the front of the
seat and pull upward.
2. Adjust the length of the seat cushion.
3. Release the handle and make sure the
seat cushion locks into position.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
Adjusting front seat side bolster settings
•
Adjusting front seat lumbar support
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
187
Adjusting front seat side bolster
settings
*
Enhance comfort in the front seat by adjust-
ing the sides of the backrest.
The multifunction control is located on the side of the
seat cushion.
The side bolsters in the front seat backrests
can be inflated/deflated to adjust the amount
of support provided. The settings for the multi-
functional seats can be adjusted using either
the mutifunction control on the seat or the
center display. The adjustment settings are
shown in the center display.
To adjust the side bolsters:
1. Activate the multifunction control by turn-
ing it upward/downward
. The seat set-
tings view will appear in the center dis-
play.
2. Select
Side bolsters
in the seat settings
view.
•
Press the front part of the four-way but-
ton to increase side bolster support
.
•
Press the rear part of the four-way but-
ton to decrease side bolster support
.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat lumbar support
•
Adjusting the passenger seat from the
driver's seat
Adjusting front seat lumbar
support
*
Use the control on the side of the seat cush-
ion to adjust the lumbar support.
Multifunction control, in vehicles with four-way lum-
bar support
*
.
Control in vehicles with two-way lumbar support
*
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
SEATS AND STEERING WHEEL
* Option/accessory.
188
Lumbar support is adjusted using the multi-
function control in vehicles with four-way lum-
bar support
*
, or the round button in vehicles
with two-way lumbar support
*
. The control is
located on the side of the seat cushion.
Depending on the selected equipment level,
the lumbar support can be adjusted forward/
rearward and up/down (four-way lumbar sup-
port) or forward/backward (two-way lumbar
support).
Adjusting lumbar support in vehicles
with four-way lumbar support
1. Activate the multifunction control by turn-
ing the control
upward/downward. The
seat settings view will appear in the center
display.
2. Select
Lumbar
in the seat settings view.
•
Press the round button up
/down
to move the lumbar support upward/
downward.
•
Press the front part
of the button to
increase lumbar support.
•
Press the rear part
of the button to
decrease lumbar support.
Adjusting lumbar support in vehicles
with two-way lumbar support
1. Press the front part
of the round button
to increase lumbar support.
2. Press the rear part
of the round button
to decrease lumbar support.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
189
Adjusting the passenger seat from
the driver's seat
*
The front passenger seat can be adjusted
from the driver's seat.
Activating the function
The function is activated via the function view
in the center display:
Tap the
Adjust Passenger
Seat
button to activate.
Adjust passenger seat
The driver must adjust the passenger seat
within 10 seconds of activating the function. If
no adjustment is made within this time, the
function will be deactivated.
The driver adjusts the passenger seat using
the controls on the driver's seat:
Move the passenger seat forward/rear-
ward by moving the control forward/rear-
ward.
Change the backrest tilt of the passenger
seat by moving the control forward/back-
ward.
Related information
•
•
•
•
Storing positions for seats, mirrors and
head-up display
•
Using stored positions for seats, mirrors
and head-up display
•
Adjusting front seat massage settings
•
•
•
Adjusting front seat side bolster settings
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
* Option/accessory.
190
Folding down the rear seat
backrests
*
The rear seat backrest is split into two sec-
tions. The two sections can be folded forward
individually.
WARNING
•
Adjust the seat and ensure it locks into
position before driving. Use caution
when adjusting the seat. Uncontrolled
or careless adjustments could lead to
injury.
•
Long objects must always be securely
tied down to help prevent injury or
damage in the event of sudden brak-
ing.
•
Always turn off the engine and apply
the parking brake when loading or
unloading the vehicle.
•
Put the gear selector in
P
to help pre-
vent the gear selector from being inad-
vertently moved.
When the backrest is folded down, make
sure there are no objects in the rear seat,
and the seat belts are not buckled. Other-
wise there is a risk of damage to the
upholstery.
The armrest
*
in the center seat must be
raised before the seat backrest is folded
down.
The ski hatch
*
must be closed before the
seat backrest is folded down.
The rear seat must be in the upright posi-
tion when private locking is activated in
order for the seats to lock. Seats in the
folded-down position will not lock.
The front seats may need to be pushed for-
ward and/or the backrest adjusted so that
the rear seat backrests can be fully low-
ered.
Folding down the backrests
The vehicle must be stationary and at least
one of the rear doors must be open before a
backrest can be folded down.
Buttons for folding down the seats, located on the
top section of the left-side rear seat.
1. Make sure that the rear seat is unoccupied
and that there are no objects on the seat.
2. Push down the center seat's head
restraint manually.
3. Press and hold one of the buttons located
on the left side of the parcel shelf in the
rear window.
4. The backrest lock will release but the
backrest will remain in the same position.
The head restraint will fold down automat-
ically.
5. Manually fold the backrest down to its
horizontal position.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
SEATS AND STEERING WHEEL
}}
* Option/accessory.
191
Folding up the backrest
To fold up the backrest to the upright position
manually:
1. Move the backrest upward/rearward.
2. Press the backrest until it locks into posi-
tion.
3. Fold up the head restraints manually.
4. Adjust the center head restraint if neces-
sary.
WARNING
Make sure that the rear seat backrest and
head restraint are locked securely in place
after the seat is folded up.
The head restraints at the outer seats must
always be raised when there is a passenger
in one of these spots of the rear seat.
Related information
•
Adjusting the rear seat head restraints
(p. 191)
•
•
Activating and deactivating private locking
(p. 259)
Adjusting the rear seat head
restraints
Adjust the center head restraint in the rear
seat to the seat occupant's height. Fold down
the outboard head restraints
*
to improve rear
visibility.
Adjusting the center seat head
restraint
The center head restraint should be adjusted
to suit the passenger's height. The entire back
of the head should be covered if possible.
Manually move the restraint up or down as
needed.
To lower the restraint, push and hold the but-
ton (see illustration) while carefully lowering
the head restraint.
WARNING
The center seat head restraint must be in
its lowest position when the seat is not
occupied. When the center seat is occu-
pied, the head restraint must be correctly
adjusted to the passenger's height, cover-
ing the entire back of the head if possible.
Folding the rear seat outboard head
restraints using the center display
*
The outer head restraints can be folded via the
center display's function view. The head
restraint can be folded down when the vehicle
is in ignition mode
0
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст