Volvo S60 Recharge Plug-in Hybrid (2021 year). Manual in english — page 15
KEY, LOCKS AND ALARM
261
Alarm
The alarm emits sound and light signals if
anyone without a valid remote key attempts
to break into the vehicle or interferes with the
start battery or alarm siren.
Alarm indicator
A red indicator light on the dashboard shows
the status of the alarm:
•
Indicator off - the alarm is disarmed.
•
Indicator flashes once every two seconds -
the alarm is armed.
•
The indicator flashes quickly after the
alarm has been disabled for up to
30 seconds or until the ignition is put in
I
mode – the alarm has been triggered.
When armed, the alarm will be triggered if:
•
the hood, trunk lid or any door is opened.
•
a battery cable is disconnected.
•
the alarm siren is disconnected.
Alarm signals
The following occurs if the alarm is triggered:
•
A siren will sound for 30 seconds or until
the alarm is turned off.
•
The hazard warning flashers will flash for
5 minutes or until the alarm is turned off.
If the reason the alarm was triggered is not
rectified, the alarm cycle will repeat up to 10
times
16
.
Symbols and messages
Symbol Message
Meaning
Alarm sys-
tem failure
Service
required
Contact a work-
shop
‒
an
authorized Volvo
workshop is rec-
ommended.
Do not attempt to repair or alter any of the
components in the alarm system yourself.
Any such attempt could affect the terms
and conditions of your insurance policy.
Related information
•
Arming and disarming the alarm (p. 262)
16
Certain markets only.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
KEY, LOCKS AND ALARM
262
Arming and disarming the alarm
The alarm is armed when the vehicle is
locked and disarmed when the vehicle is
unlocked. The alarm can also be disarmed
without a functioning key.
Arming and disarming the alarm
The alarm is armed when the vehicle is locked
and disarmed when the vehicle is unlocked.
Disarming the alarm without a functioning
remote key
The vehicle can be unlocked and disarmed
even if the remote key is not functioning e.g. if
the battery is discharged.
1. Open the driver's door using the detacha-
ble key blade.
> This will trigger the alarm.
Location of the backup key reader in the cup holder.
2. Place the remote key on the key symbol in
the backup reader in the tunnel console's
cup holder.
3. Turn the start knob clockwise and release.
> The alarm will be disarmed.
Turning off a triggered alarm
–
Press the unlock button on the remote key
or put the ignition into mode
I
by turning
the start knob clockwise and then releas-
ing it.
Related information
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
264
Driver support systems
The vehicle is equipped with a number of
driver support systems that can provide the
driver with active or passive assistance in var-
ious situations.
The systems can, for example, help the driver:
•
maintain a set speed
•
maintain a set time interval to the vehicle
ahead
•
help prevent a collision by warning the
driver and applying the brakes
•
park the vehicle.
Some of the systems are standard and others
are options. This also varies from market to
market.
Related information
•
IntelliSafe – driver support and safety
(p. 29)
•
Speed-dependent steering wheel resis-
tance (p. 264)
•
Electronic Stability Control (p. 265)
•
•
•
•
•
•
•
•
•
•
Steering assistance at risk of collision
(p. 331)
•
•
•
•
•
•
•
•
•
Speed-dependent steering wheel
resistance
Speed-dependent power steering increases
the steering wheel resistance in pace with
the vehicle's speed, which can help give the
driver an enhanced feeling of control and sta-
bility. Steering is stiffer on highways. When
parking and at low speeds, it will be easier to
move the steering wheel.
Reduced power
In rare situations, the power steering may
need to work at reduced power and the steer-
ing wheel may then feel more difficult to
move. This may happen when the power
steering becomes too hot and needs to be
temporarily cooled. It can also happen if there
is a disturbance in power supply.
If there is reduced power, the
message
Power steering
Assistance temporarily
reduced
and this symbol are
shown in the instrument
panel.
While the power steering is working at
reduced power, the driver support functions
and systems with steering assistance are not
available.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
265
WARNING
If the temperature rises too high, the power
steering may be forced to switch off com-
pletely. In such a situation, the driver dis-
play shows the message
Power steering
failure
Stop safely
along with a symbol.
Changing the level of steering wheel
resistance
*
In INDIVIDUAL drive mode, the level of steer-
ing wheel resistance can be adjusted.
1. Tap
Settings
in the center display's Top
view.
2. Select
My Car
Drive Modes
Steering Force
.
Steering wheel resistance settings can only be
accessed if the vehicle is stationary or is mov-
ing straight ahead at a low speed.
Related information
•
Driver support systems (p. 264)
•
Electronic Stability Control
The Electronic Stability Control (ESC
1
) func-
tion helps the driver avoid skidding and
improves the vehicle's directional stability.
This symbol will be displayed
in the instrument panel when
the system is intervening.
When the system has inter-
vened to apply the brakes, a
pulsing sound may be heard
and the vehicle may accelerate more slowly
than expected when the accelerator pedal is
depressed.
The system consists of the following sub-func-
tions:
•
Stability control
2
•
Spin control and active yaw control
•
Engine drag control
•
Trailer Stability Assist
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and help make it safer – it cannot han-
dle all situations in all traffic, weather
and road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgment. The driver is always respon-
sible for ensuring the vehicle is driven
in a safe manner, at the appropriate
speed, with an appropriate distance to
other vehicles, and in accordance with
current traffic rules and regulations.
Stability control
2
This function helps control the driving and
braking force of each individual wheel in an
attempt to stabilize the vehicle.
Spin control and active yaw control
This function is active at low speeds and
brakes the wheels that are spinning to transfer
1
Electronic Stability Control
2
Also called traction control.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
266
additional power to wheels that are not spin-
ning.
This function can also help prevent the wheels
from spinning while the vehicle is accelerating.
Engine drag control
Engine drag control (EDC
3
) can help prevent
inadvertent wheel lock, e.g. after downshifting
or using engine braking when driving at low
speeds on a slippery surface.
Inadvertent wheel lock while driving could
impair the driver's ability to steer the vehicle.
Trailer Stability Assist
*
4
Trailer Stability Assist (TSA
5
) is designed to
help stabilize a vehicle that is towing a trailer if
the vehicle and trailer have begun to sway.
Trailer Stability Assist is deactivated if
ESC
Sport Mode
is activated.
Related information
•
Driver support systems (p. 264)
•
Activating or deactivating Sport mode for
Electronic Stability Control (p. 267)
•
Electronic Stability Control symbols and
messages (p. 268)
•
Electronic Stability Control in sport
mode
The stability system (ESC
6
) is always acti-
vated and cannot be switched off. However,
the driver can select
ESC Sport Mode
,
which offers more active driving characteris-
tics.
With the
ESC Sport Mode
sub-function
selected, intervention from the system is
reduced and more lateral movement is permit-
ted, giving the driver more control of the vehi-
cle than usual.
When
ESC Sport Mode
is selected, the func-
tion may seem to be disabled even though it
continues to assist the driver.
When
ESC Sport Mode
is selected, the
trailer stabilizer (TSA
7
) is switched off.
ESC Sport Mode
also helps provide more
traction, even if the vehicle gets stuck or is
driving on a loose surface such as deep snow
or loose sand.
3
Engine Drag Control
4
Trailer Stability Assist is included if the vehicle is equipped with a Volvo original towbar.
5
Trailer Stability Assist
6
Electronic Stability Control
7
Trailer Stability Assist
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
267
Related information
•
Electronic Stability Control (p. 265)
•
Activating or deactivating Sport mode for
Electronic Stability Control (p. 267)
•
Activating or deactivating Sport
mode for Electronic Stability
Control
The stability system (ESC
8
) is always acti-
vated and cannot be switched off. However,
the driver can select Sport mode, which
offers more active driving characteristics.
Activate or deactivate the
function using this button in
the center display's Function
view.
•
Illuminated button indicator light – the
function is activated.
•
Extinguished button indicator light – the
function is deactivated.
When
ESC Sport Mode
is
activated, this symbol will
illuminate with a steady glow
in the instrument panel. It will
remain on until the driver
deactivates the function or
until the engine is turned off.
The system will return to normal mode the
next time the engine is started.
The
ESC Sport Mode
function cannot be
selected when any of the following functions
are activated:
•
Cruise control
•
Adaptive Cruise Control
*
•
Pilot Assist
*
Related information
•
Electronic Stability Control in sport mode
(p. 266)
•
Electronic Stability Control (p. 265)
8
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
268
Electronic Stability Control
symbols and messages
A number of symbols and messages related
to Electronic Stability Control (ESC
9
) may be
displayed in the instrument panel. Several
examples are provided below.
Symbol
Message
Meaning
Steady glow for approx. 2 seconds System check when the engine is started.
Flashing light
The system is actively operating.
Steady glow
Sport mode is activated.
NOTE!
The system is not deactivated in this mode, but has parti-
ally reduced functionality.
9
Electronic Stability Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
269
Symbol
Message
Meaning
ESC
Temporarily off
The system's functionality has been temporarily reduced due to high brake system tempera-
tures. The function will be automatically reactivated when the brakes have cooled.
ESC
Service required
The system is not functioning properly. Stop the vehicle in a safe place, turn off the engine
and then restart it.
A text message can be erased by briefly press-
ing the
button in the center of the right-
side steering wheel keypad.
If the message persists: Contact a workshop
‒
an authorized Volvo workshop is recom-
mended.
Related information
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
270
Connected Safety
10
Connected Safety communicates information
between your vehicle and other vehicles via
the Internet
11
. The function is designed to
notify the driver of any hazardous road condi-
tions ahead.
The function can notify the driver if another
vehicle further down the road has activated its
hazard warning flashers or detected slippery
road conditions. You will also be notified if
your own vehicle detects slippery road condi-
tions.
Connected Safety can assist the driver with
the following:
•
Hazard warning flashers alert
•
Slippery road alerts
Connected Safety communication between
vehicles only works for vehicles that are equip-
ped with the function and have it activated.
Hazard warning flashers alert
If your vehicle's hazard warning flashers are
activated, information on this can be sent to
other vehicles approaching your location.
When your vehicle
approaches a vehicle with its
hazard warning flashers on,
this symbol will appear in the
instrument panel.
In vehicles equipped with a head-up display,
the warning symbols for Connected Safety
will also be displayed there.
Slippery road alerts
If your own car detects reduced friction
between your tires and the road, information
on this can be sent to vehicles approaching
your own car's position.
As the vehicle approaches
the area affected, this symbol
will be displayed in the instru-
ment panel to alert the driver
of slippery road conditions.
Drivers of other vehicles
receiving information via
Connected Safety will receive similar notifica-
tions as they approach the area.
In vehicles equipped with a head-up display,
the warning symbols for Connected Safety
will also be displayed there.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and help make it safer – it cannot han-
dle all situations in all traffic, weather
and road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgment. The driver is always respon-
sible for ensuring the vehicle is driven
in a safe manner, at the appropriate
speed, with an appropriate distance to
other vehicles, and in accordance with
current traffic rules and regulations.
Related information
•
Driver support systems (p. 264)
•
Activating or deactivating Connected
Safety (p. 271)
•
Connected Safety limitations (p. 271)
•
10
Not available in all markets.
11
There may be a charge for transmitting data over the Internet, depending on your service plan.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
271
Activating or deactivating
Connected Safety
For Connected Safety to be able to share
information about road conditions with other
drivers, the function must be activated. If you
do not wish to share information, the function
can be deactivated.
Activate or deactivate the
function using this button in
the center display's Function
view.
•
Illuminated button indicator light – the
function is activated.
•
Extinguished button indicator light – the
function is deactivated.
At activation, the driver must accept the spe-
cial terms and conditions shown in the display
before an Internet connection
12
can be estab-
lished. The driver must, for example, accept
that data is sent from the vehicle using the
driver's cellular phone.
Even when your vehicle is not connected to
the Internet, you will still be notified if the sys-
tem in your own vehicle detects slippery road
conditions. For Connected Safety to function
at full capacity, your vehicle needs to be con-
nected to the Internet.
Related information
•
•
•
Terms of use and data sharing (p. 518)
•
Connected Safety limitations (p. 271)
Connected Safety limitations
Information on vehicles with activated hazard
warning flashers or which have detected slip-
pery road conditions is not always communi-
cated between all vehicles in the affected
area.
This may be the case if:
•
No or insufficient Internet connection.
•
The maneuvers (steering wheel move-
ments, acceleration or braking) made by
the vehicles on slippery surfaces are too
weak for friction between the tires and
road to be detected.
•
Vehicles that have detected slippery road
conditions or activated hazard warning
flashers have not activated the function.
•
Vehicles that have detected slippery road
conditions or activated hazard warning
flashers are not equipped with the func-
tion.
•
Insufficient GPS/satellite navigation may
prevent warnings.
•
Slippery road conditions were detected or
hazard warning flashers were activated on
a road that is not registered in the Volvo
Cars database.
•
Connected Safety is not developed on all
markets and does not cover all areas. Con-
12
There may be a charge for transmitting data over the Internet, depending on your service plan.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
272
sult a Volvo retailer for more information
on covered areas.
WARNING
•
In certain situations, the function may
give false warnings of slippery road
conditions.
•
The function cannot always detect
other vehicles with activated hazard
warning factors or detect all stretches
of road with slippery conditions.
Related information
•
•
Road Sign Information
*
The Road Sign Information (RSI
13
) function
can help the driver observe speed-related
road signs.
Examples of signs that can be detected
14
.
If the vehicle passes a speed limit sign, it will
be displayed in the instrument panel and the
head-up display
*
.
There are also subfunctions for Road Sign
Information (RSI
15
) that can alert the driver if
the speed limit has been exceeded or if there
are speed cameras nearby.
In certain markets, the Road Sign Informa-
tion
*
function is only available in combina-
tion with Sensus Navigation
*
.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and help make it safer – it cannot han-
dle all situations in all traffic, weather
and road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgment. The driver is always respon-
sible for ensuring the vehicle is driven
in a safe manner, at the appropriate
speed, with an appropriate distance to
other vehicles, and in accordance with
current traffic rules and regulations.
13
Road Sign Information
14
Road signs differ according to market
‒
the illustrations shown here are just some examples.
15
Road Sign Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
273
Related information
•
Driver support systems (p. 264)
•
Activating or deactivating Road Sign Infor-
mation
•
•
Road Sign Information and Sensus
Navigation
•
Speed limit and speed camera warnings
from Road Sign Information
•
Activating or deactivating Road
Sign Information
*
The Road Sign Information (RSI
16
) function is
optional – the driver can choose to have the
function activated or deactivated.
Activate or deactivate the
function using this button in
the center display's Function
view.
•
Illuminated button indicator light – the
function is activated.
•
Extinguished button indicator light – the
function is deactivated.
Related information
•
•
Road Sign Information
*
display
Road Sign Information (RSI
17
) displays road
signs in different ways depending on the sign
and situation.
Example
18
of registered speed information.
When the function has registered a speed
limit sign, the sign will be displayed as a sym-
bol in the instrument panel and a colored
marking will be shown in the speedometer's
speed scale.
If the vehicle is equipped with Sensus
Navigation
*
, speed-related information will
also be retrieved from map data, which means
that the instrument panel can display or
change information about speed limits even if
the vehicle has not passed a speed-related
sign.
16
Road Sign Information
17
Road Sign Information
18
Road signs differ according to market
‒
the illustrations shown here are just examples.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
274
Signs for "School" and "Children
playing"
If the warning sign "School"
or "Children playing" is
included in the satellite navi-
gator's map data
19
, a symbol
of this type will be displayed
in the instrument panel.
Related information
•
•
Road Sign Information and Sensus
Navigation
*
If the vehicle is equipped with Sensus
Navigation
*
, speed-related information will be
provided in the following situations:
•
In cases where the speed limit is given
indirectly, e.g. signs for highways or other
major roads.
•
If a previously detected speed sign is
deemed to be no longer valid and no new
sign has been passed.
In certain markets, the Road Sign Informa-
tion
*
function is only available in combina-
tion with Sensus Navigation
*
.
If a downloaded third-party app is used for
navigation, there is no support for speed-
related information.
Related information
•
Speed limit and speed camera
warnings from Road Sign
Information
*
There are subfunctions for Road Sign Infor-
mation (RSI
20
) that can alert the driver if the
speed limit has been exceeded or if there are
speed cameras nearby.
Example of speed camera and speed limit informa-
tion in the instrument panel
Speed limit warning
When Speed Warning is acti-
vated, the symbol for the cur-
rent speed limit in the instru-
ment panel
21
will flash tem-
porarily if that speed is excee-
ded.
19
Only vehicles with Sensus Navigation
*
.
20
Road Sign Information
21
Road signs differ by market – the illustration shown here is just an example.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
275
The driver can be alerted if the vehicle is
exceeding a detected speed limit and is
approaching a speed camera.
Speed Limit Warning
warns the driver if the
vehicle's speed has exceeded the applicable
speed limit or the stored maximum speed. The
warning will be repeated once after
about 30 seconds in that speed limit area if
the driver does not slow down.
An additional warning will not be provided
unless the vehicle's speed is reduced by at
least 5 km/h (3 mph) and then exceeds the
speed limit again or the vehicle enters a new/
different speed limit area.
For an audible alert to be provided if the
speed is exceeded, the
Speed Limit
Warning
function must be activated and
the
Road Sign Audio Warning
sub-func-
tion must be
On
. Audible alerts are provi-
ded if the vehicle's speed exceeds the
speed displayed by Road Sign Information
in the instrument panel.
Speed camera warning
Vehicles equipped with Road
Sign Information and Sensus
Navigation can provide infor-
mation on upcoming speed
cameras in the instrument
panel
22
.
If the vehicle exceeds a detected speed limit
with the
Speed Limit Warning
function acti-
vated, the driver is given a speed warning
when the vehicle is approaching a speed cam-
era if the navigation map for the vehicle's cur-
rent location contains information on speed
cameras.
It is possible to receive an audible alert for
speed cameras regardless of the vehicle's
speed and whether or not the speed limit is
exceeded, even if the
Road Sign Audio
Warning
function is deactivated.
Related information
•
•
Activating or deactivating warnings from
Road Sign Information
•
Activating or deactivating
warnings from Road Sign
Information
*
The Road Sign Information (RSI
23
) subfunc-
tion
Speed Limit Warning
is optional – the
driver can choose to have the subfunction
activated or deactivated.
Activating Speed Warning
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the center
display's Top view.
2. Select
Speed Limit Warning
.
> The function is activated and a speed
limit selector is displayed.
Adjusting the Speed Warning limit
The driver can adjust the settings to be alerted
at a higher speed than the posted speed limit.
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the center
display's Top view.
2. Select
Speed Limit Warning
.
> The function is activated and a speed
limit selector is displayed.
22
Information on speed cameras on the navigation map is not available for all markets/areas.
23
Road Sign Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
276
3. Tap the up/down arrows on the screen to
adjust the speed at which the Speed
Warning will be given.
Please note that the set
warning limit will not be used
when a speed camera symbol
is displayed in the instrument
panel.
Activating audible alert for Speed
Warning
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the center
display's Top view.
2. Select/deselect
Road Sign Audio
Warning
to activate/deactivate the audi-
ble alert.
When
Road Sign Audio Warning
is acti-
vated, the driver will also be alerted if the vehi-
cle is approaching a one-way/"no-entry" road
or entrance.
Activating speed camera alerts
If the vehicle is equipped with Sensus
Navigation
*
and map data contains informa-
tion on speed cameras, the driver can choose
to receive an audible alert if the vehicle is
approaching a speed camera.
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the center
display's Top view.
2. Select/deselect
Speed Camera Audio
Warning
to activate/deactivate the speed
camera audible alert.
Related information
•
•
Speed limit and speed camera warnings
from Road Sign Information
•
Road Sign Information
*
limitations
Road Sign Information (RSI
24
) functionality
may be reduced in certain situations.
The function could have reduced functionality
due to e.g.:
•
faded road signs
•
signs located in a curve in the road
•
twisted or damaged signs
•
signs positioned high above the road
•
fully/partially obstructed or poorly posi-
tioned signs
•
signs partially or fully covered by frost,
snow and/or dirt
•
digital road maps
25
that are outdated,
incorrect or do not contain speed informa-
tion
26
In certain markets, the Road Sign Informa-
tion
*
function is only available in combina-
tion with Sensus Navigation
*
.
24
Road Sign Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
277
Certain types of bike carriers that are con-
nected to the trailer socket may be inter-
preted as a connected trailer by the RSI
function. In such cases, the instrument
panel may indicate incorrect speed infor-
mation.
The function uses the vehicle's camera and
radar sensor, which has certain general
limitations.
Related information
•
•
Camera/radar sensor limitations (p. 377)
Cruise control
Cruise Control (CC
27
) can help the driver
maintain an even speed to provide a more
relaxing driving experience on highways and
long, straight roads with even traffic flows.
Function buttons and symbols
: Activates Cruise Control from
standby mode and resumes the set speed
: Increases the set speed
:
From standby mode
– activates
Cruise Control and sets the current speed
:
From active mode
– deactivates/
puts Cruise Control in standby mode
: Reduces the set speed
Marker for set speed
The vehicle's current speed
Set speed
In vehicles equipped with Adaptive Cruise
Control
*
(ACC
28
), it is possible to switch
between Cruise Control and Adaptive
Cruise Control.
25
Vehicles equipped with Sensus Navigation
*
.
26
Map data and speed information is not available for all areas.
27
Cruise Control
28
Adaptive Cruise Control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст