Volvo XC90 Twin Engine (2020 year). Manual in english — page 22
DRIVER SUPPORT
* Option/accessory.
379
BLIS is active when the driver's vehicle is trav-
elling at a speed above 10 km/h (6 mph).
If passing vehicles drive more than 15 km/h
(9 mph) faster than the driver's vehicle, BLIS
will not react.
The lamp illuminates on the side of the car
where the system has detected the vehicle.
If the car is overtaken on both sides at the
same time then both lamps illuminate.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
Driving support systems (p. 300)
•
Activating or deactivating BLIS (p. 379)
•
•
Activating or deactivating BLIS
The BLIS
85
function can be activated or deac-
tivated.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – the function is
deactivated.
If BLIS is activated when starting the engine,
the function is confirmed by the door mirror
indicator lamps blinking once.
If BLIS was deactivated when the engine was
switched off, it will continue to be deactivated
when the engine is next started and no indica-
tor lights will then be illuminated.
Related information
•
•
85
Blind Spot Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
380
Limitations of BLIS
The BLIS
86
function may have limitations in
certain situations.
Keep the surface indicated clean – on both the left
and right-hand sides of the car
87
.
Examples of limitations:
•
Dirt, ice and snow covering the sensors
may reduce the functions and deactivate
alerts.
•
The BLIS function is automatically deacti-
vated if a trailer, bicycle rack or similar is
connected to the car's electrical system.
•
For good performance of BLIS, there
should be no bicycle rack, luggage carrier
or similar mounted on the car's towbar.
WARNING
•
BLIS does not work on sharp bends.
•
BLIS does not work when the car is
reversing.
This function uses the car's camera and
radar units, which have certain general lim-
itations.
Related information
•
•
Limitations for camera and radar unit
(p. 358)
86
Blind Spot Information
87
NOTE: The illustration is schematic - details may vary depending on car model.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
381
Messages for BLIS
A number of messages regarding BLIS
88
can
be shown in the driver display. Here are some
examples.
Message
Specification
Blind spot sensor
Service required
The system does not function as it should. A workshop should be contacted
A
.
Blind spot system off
Trailer attached
BLIS and CTA
B
have been deactivated as a trailer has been connected to the car's electrical system.
A
An authorised Volvo workshop is recommended.
B
Cross Traffic Alert
*
A text message can be cleared by briefly
pressing the
button, located in the centre
of the steering wheel's right-hand keypad.
If a message persists, contact a workshop
A
.
Related information
•
•
88
Blind Spot Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
382
Cross Traffic Alert
*
89
Cross Traffic Alert (CTA) is a driver support
that supplements BLIS
90
and is designed to
help the driver detect traffic crossing behind
the car when it is reversing.
The
auto-brake
subfunction can help the
driver to stop the car in the event of a risk of
collision with an unobserved vehicle.
Examples of areas where CTA can assist the driver to
detect obstacles during reversing.
CTA supplements BLIS by detecting the
approach of crossing traffic during reversing,
such as when reversing out of a parking
space.
CTA is primarily designed to detect vehicles. In
favourable conditions it may also be able to
detect smaller objects, such as cyclists and
pedestrians.
CTA is only active if the car rolls backwards or
if reverse gear has been selected.
If CTA senses that something is approaching
from the side, this is also indicated with:
•
an acoustic signal - the sound is heard in
the left-hand or right-hand speaker
according to the direction from which the
object approaches.
•
an illuminated icon in the
Park Assist
System
graphic on the screen.
•
an icon on the Park assist camera top
view.
Illuminated icon for CTA in the
Park Assist
System
graphic on the screen.
If the driver does not observe the warning
from CTA and a collision is unavoidable, the
auto-brake
function takes effect to stop the
car, after which the driver display shows an
explanatory text message on why the car was
braked.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
89
Cross traffic alert when the car is reversing.
90
Blind Spot Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
383
Related information
•
Driving support systems (p. 300)
•
Activating or deactivating Cross Traffic
Alert
•
Limitations of Cross Traffic Alert
•
Messages for Cross Traffic Alert
•
•
Activating or deactivating Cross
Traffic Alert
*
91
The driver can select to switch off the
warn-
ing
in the Cross Traffic Alert (CTA) function –
the
auto brake
subfunction cannot be
switched off, however, and continues to be
active.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – warning signal
and indication on display for the function
is deactivated.
The function is activated automatically each
time the engine is started.
Related information
•
•
Limitations of Cross Traffic Alert
Limitations of Cross Traffic Alert
*
92
The Cross Traffic Alert (CTA) function with
auto-brake
may have limited functionality in
certain situations. Brake intervention is active
at speeds below 15 km/h.
WARNING
The
auto-brake
subfunction can only
detect and brake for other vehicles that are
moving –
not
for stationary obstacles, a
cyclist or a pedestrian, for example.
CTA has a certain limitation – the CTA sensors
cannot "see" through other parked vehicles or
obstructions, for example.
Here are some examples of situations where
CTA’s "field of vision" may be already limited
and approaching vehicles cannot therefore be
detected until they are very close:
91
Cross traffic alert when the car is reversing.
92
Cross traffic alert when the car is reversing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
384
The car is parked deep inside a parking slot.
In an angled parking slot CTA may be completely
“blind” on one side.
Blind CTA sector.
Sector in which CTA can detect/“see”.
However, as your car slowly reverses, the
angle it makes with the obstructing vehicle/
object changes and the blind sector rapidly
decreases.
Examples of further limitations
•
The
auto-brake
subfunction only detects
moving vehicles and therefore
cannot
"see" and brake for stationary obstacles, a
cyclist or a pedestrian, for example.
•
Dirt, ice and snow covering the sensors
may reduce the functions and deactivate
alerts.
•
CTA is automatically deactivated if a
trailer, bicycle rack or similar is connected
to the car's electrical system.
•
For good performance of CTA, there
should be no bicycle rack, luggage carrier
or similar mounted on the car's towbar.
This function uses the car's camera and
radar units, which have certain general lim-
itations.
Related information
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
385
Messages for Cross Traffic Alert
*
93
A number of messages regarding Cross
Traffic Alert (CTA) can be shown in the driver
display. Here are some examples.
Message
Specification
Blind spot sensor
Service required
The system does not function as it should. A workshop should be contacted
A
.
Blind spot system off
Trailer attached
BLIS
B
and CTA have been deactivated as a trailer has been connected to the car's electrical system.
A
An authorised Volvo workshop is recommended.
B
Blind Spot Information System
A text message can be cleared by briefly
pressing the
button, located in the centre
of the steering wheel's right-hand keypad.
If a message persists, contact a workshop
A
.
Related information
•
•
•
Limitations of Cross Traffic Alert
93
Cross traffic alert when the car is reversing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
386
Road Sign Information
*
The Road Sign Information function (RSI
94
)
can help the driver to observe speed-related
road signs and certain prohibition signs.
Examples of readable signs
95
.
RSI can provide information about such things
as current speed, when a motorway or road is
starting/ending, when overtaking is prohibited
or when the direction of travel is one-way.
If the car passes a speed limit sign, it will be
shown on the driver's display and the head-up
display
*
.
In certain markets, the Road Sign Informa-
tion function
*
is only available in combina-
tion with Sensus Navigation
*
.
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
Driving support systems (p. 300)
•
Activating or deactivating road sign infor-
mation
•
Display mode for road sign information
•
Road Sign Information and Sensus
Navigation
•
Warning for speed limitation and speed
camera from road sign information
•
Limitations of Road Sign Information
94
Road Sign Information
95
Road signs are market-dependent - illustrations in these instructions only show a few examples.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
387
Activating or deactivating road
sign information
*
The Road Sign Information function (RSI
96
) is
optional – the driver can choose to activate or
deactivate this function.
Activate or deactivate the
function using this button in
the centre display's function
view.
•
GREEN button indication – the function is
activated.
•
GREY button indication – the function is
deactivated.
•
If the automatic speed limiter function
is activated, road sign information is
shown in the driver display even if the
Road Sign Information function is not
activated.
•
To remove road sign information from
the driver display, you must deactivate
both
the automatic speed limiter and
Road Sign Information.
•
When the automatic speed limiter
function is activated but Road Sign
Information is deactivated, no warn-
ings are given from Road Sign Infor-
mation. Road Sign Information must
also be activated in order to receive
warnings.
Related information
•
•
Automatic speed limiter (p. 314)
•
Limitations of Road Sign Information
Display mode for road sign
information
*
The Road Sign Information function (RSI
97
)
shows road signs in different ways depend-
ing on the sign and the situation.
Example
98
of detected speed information.
When the function detects a road sign with an
imposed speed limit, the driver display shows
the sign as a symbol combined with a col-
oured indication on the speedometer.
If the car is fitted with Sensus Navigation
*
,
speed-related information is also obtained
from map data, which means that the driver
display can show or change information on
the speed limit without having passed a
speed-related sign.
96
RSI: Road Sign Information.
97
Road Sign Information
98
Road signs are market-dependent - the illustrations in these instructions only show examples.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
388
An additional
98
sign, such as
"no overtaking", may be
shown together with the
speed limit symbol.
If the driver enters a road
marked with a no-entry sign
at the roadside, the symbol
for this sign
98
flashes on and
off on the driver display as a
warning.
If the car is equipped with Sensus Navigation
*
,
information from map data is used to deter-
mine whether the car is being driven in the
wrong direction.
The driver can also get an acoustic warning
when driving towards a road marked with a
no-entry sign if the
Road Sign Audio
Warning
function is activated.
Speed limit or end of motorway
When the function detects an "indirect speed
limit sign" stating the end of the current speed
limit – e.g. at the end of a motorway – a sym-
bol appears with the corresponding road sign
in the driver's display.
If the car is equipped with Sensus Navigation
*
,
direct speed limit signs are normally displayed
– indirect speed limit signs are only displayed
if map data has no information on the speed
limit for the road section in question.
Example of indirect speed limit sign
98
:
End of all restrictions.
End of motorway.
The driver display symbol extinguishes after
10-30 seconds and remains so until the next
speed related sign is passed.
Changed speed limit
When passing a direct speed limit sign when a
speed limit changes, a symbol with the corres-
ponding road sign appears in the driver's dis-
play.
Example of direct speed limit
sign
98
.
The driver display symbol extinguishes after
about 5 minutes until the next speed-related
sign is passed.
If the car is fitted with Sensus Navigation
*
,
speed limit signs are shown in the driver dis-
play when map data contains information on
the speed limit for the road section in ques-
tion, even if no direct sign has been passed. If
there is no information in map data, the sign
goes off after approx. 3 minutes after the last
passing of a speed limit sign.
98
Road signs are market-dependent - the illustrations in these instructions only show examples.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
389
Additional signs
Examples of additional signs
98
.
Sometimes different speed limits are signed
for the same road - an additional sign then
indicates the circumstances under which the
different speeds apply. The road section may
be particularly susceptible to accidents in rain
and/or fog, for example.
An additional sign relating to rain is displayed
only if the windscreen wipers are in use.
If a trailer is connected to the car's electrical
system and you pass a speed sign with the
additional sign "trailer", the indicated speed
will appear on the driver display.
Some speed limits only apply
after a certain distance or at a
certain time of day. The driv-
er's attention is drawn to this
fact by means of a symbol for
an additional sign below the
speed symbol. The additional
symbol in the driver display will show either
“DIST” or “TIME”.
A symbol for additional sign
in the form of an empty frame
under the driver display's
speed symbol
98
means that
the function has detected an
additional sign with supple-
mentary information for the
current speed limit.
Sign for "School" and "Children at
play"
If a warning sign
98
for
"School" or "Children at play"
is included in the satellite
navigator's map data
99
, the
driver display shows a sign of
this type.
Related information
•
•
Limitations of Road Sign Information
98
Road signs are market-dependent - the illustrations in these instructions only show examples.
99
Only in cars with Sensus Navigation
*
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
* Option/accessory.
390
Road Sign Information and Sensus
Navigation
*
If the car is equipped with Sensus Navigation
*
,
speed information is read from the navigation
unit in the following cases:
•
On detection of signs that indirectly indi-
cate a speed limit, such as motorway, dual
carriageway and city limit signs.
•
If a previously detected speed sign is
assumed not to apply any longer, but no
new sign has been detected.
In certain markets, the Road Sign Informa-
tion function
*
is only available in combina-
tion with Sensus Navigation
*
.
If a downloaded third-party app is used for
navigation then there is no support for
speed-related information.
Related information
•
Warning for speed limitation and
speed camera from road sign
information
*
Road sign information (RSI
100
) includes sub-
functions that can warn the driver if a speed
limit has been exceeded or in connection with
speed cameras.
Examples of information on speed camera and speed
limit in the driver display.
Speed Limit Warning
The speed warning is given
by the driver display sym-
bol
101
showing the applicable
maximum permitted speed
temporarily flashing when
this speed is exceeded.
A speed warning is always given if the speed
limit is exceeded in connection with speed
camera information.
Speed Limit Warning
warns the driver when
the applicable speed limit or a preselected
"top speed" is exceeded – this warning is
repeated once after approx. 1 minute within
the same speed limit area unless the driver
reduces the speed.
A new warning for exceeding the speed limit,
including a reminder, will be given only when
the car reaches a new/different speed limit
area.
To get an acoustic warning if you exceed
the required speed, the
Speed Limit
Warning
function must be activated and
the
Road Sign Audio Warning
subfunc-
tion must be set to
On
. An acoustic warn-
ing is then given if the car's speed exceeds
the speed indicated by the Road Sign
Information function in the driver display.
100
Road Sign Information
101
Road signs are customised for each market – the one shown here is just an example.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
391
Warning for speed camera
A car equipped with road
sign information and Sensus
Navigation can provide infor-
mation on an upcoming
speed camera in the driver
display.
102
If the car exceeds a detected speed limit with
the
Speed Limit Warning
function activated,
a speed warning is given when the car
approaches a speed camera, provided that the
navigation map for the area in question con-
tains information on speed cameras.
An option is available to receive an acous-
tic warning for speed cameras independ-
ently of the car's speed and exceeded
speed limit, and even if the
Road Sign
Audio Warning
function is deactivated.
Related information
•
•
Activating or deactivating warnings from
road sign information
•
Limitations of Road Sign Information
Activating or deactivating
warnings from road sign
information
*
The subfunction
Speed Limit Warning
for
Road Sign Information (RSI
103
) is optional –
the driver can choose to activate or deacti-
vate this subfunction.
Activating speed warning
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the centre
display's top view.
2. Select
Speed Limit Warning
.
> The function is activated and a speed
limit selector appears.
Adjust the limit for Speed Warning
The driver can select to receive a warning at a
higher speed than the signed speed.
Select limit for speed warning as follows:
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the centre
display's top view.
2. Select
Speed Limit Warning
.
> The function is activated and a speed
limit selector appears.
3. Adjust the limit for Speed Warning by
pressing the up/down arrows on the
screen.
Note that the function does
not give any consideration to
selected limit adjustment
when the driver display
shows the speed camera
symbol.
Activating acoustic warning in
connection with speed warning.
Change setting for acoustic warning as fol-
lows:
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the centre
display's top view.
2. Select/deselect
Road Sign Audio
Warning
to activate/switch off the acous-
tic warning.
With the
Road Sign Audio Warning
function
activated, the driver is also warned when driv-
ing towards one-way traffic/no-entry entrance.
Activate Speed camera warning
If the car is fitted with Sensus Navigation
*
and
map data contains information on speed cam-
102
Information on speed cameras on the navigation map is not available for all markets/areas.
103
Road Sign Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
392
eras, the driver can opt to receive an audible
warning when approaching a speed camera.
Change setting for acoustic warning as fol-
lows:
1. Select
Settings
My Car
IntelliSafe
Road Sign Information
in the centre
display's top view.
2. Select/deselect
Speed Camera Audio
Warning
to activate/switch off the audi-
ble speed camera warning.
Related information
•
•
Warning for speed limitation and speed
camera from road sign information
•
Limitations of Road Sign Information
Limitations of Road Sign
Information
*
The Road Sign Information (RSI
104
) function
may have limitations in certain situations.
Examples of what can reduce the function are
as follows:
•
Faded signs
•
Signs positioned on bends
•
Rotated or damaged signs
•
Signs positioned high above the roadway
•
Fully/partially obscured or poorly posi-
tioned signs
•
Signs completely or partly covered with
frost, snow and/or dirt
•
Digital road maps
105
are out-of-date, inac-
curate or have no speed information
106
.
In certain markets, the Road Sign Informa-
tion function
*
is only available in combina-
tion with Sensus Navigation
*
.
The RSI function may interpret some types
of bicycle rack, connected to the electrical
socket for trailers, as a connected trailer. In
such cases, the driver display may show
incorrect speed information.
This function uses the car's camera and
radar units, which have certain general lim-
itations.
Related information
•
•
Limitations for camera and radar unit
(p. 358)
104
Road Sign Information
105
In cars equipped with Sensus Navigation
*
.
106
Map data with speed information does not exist for all areas.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DRIVER SUPPORT
}}
* Option/accessory.
393
Driver Alert Control
The Driver Alert Control (DAC) function is
intended to help make the driver aware that
he or she is starting to drive less consistently,
e.g. if the driver becomes distracted or starts
to fall asleep.
The objective for DAC is to detect slowly dete-
riorating driving ability and it is primarily
intended for major roads. The function is not
intended for city traffic.
The function is activated when speed exceeds
65 km/h (40 mph) and remains active as long
as the speed is over 60 km/h (37 mph).
DAC reads the position of the car in the lane.
A camera detects the edge markings painted
on the carriageway and compares the align-
ment of the road with the driver’s steering
wheel movements.
The car is being driven erratically in the lane.
If driving behaviour becomes
noticeably inconsistent, the
driver is alerted by this sym-
bol in the driver display, com-
bined with an acoustic signal
and the text message
Time
to take a break
.
If the car is equipped with Sensus Navigation
*
and has the function
Rest Stop Guidance
activated, suggestions for an appropriate
place for a break are also displayed.
The warning is repeated after a time if driving
behaviour has not improved.
WARNING
Driver Alert Control should not be used to
extend a period of driving. The driver
should instead plan for breaks at regular
intervals and make sure they are well
rested.
WARNING
An alarm from Driver Alert Control should
be taken very seriously, as a sleepy driver is
often not aware of his/her own condition.
If the alarm sounds or you feel fatigued:
•
Stop the car safely as soon as possible
and rest.
Studies have shown that it is just as dan-
gerous to drive while tired as it is to drive
under the influence of alcohol or other
stimulants.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
||
DRIVER SUPPORT
* Option/accessory.
394
WARNING
•
The function is supplementary driver
support intended to facilitate driving
and make it safer – it cannot handle all
situations in all traffic, weather and
road conditions.
•
•
Driver support functions are not a sub-
stitute for the driver's attention and
judgement. The driver is always
responsible for ensuring the car is
driven in a safe manner, at the appro-
priate speed, with an appropriate dis-
tance to other vehicles, and in accord-
ance with current traffic rules and reg-
ulations.
Related information
•
Driving support systems (p. 300)
•
Activating or deactivating Driver Alert
Control (p. 394)
•
Select rest stop guidance in the event of a
warning from Driver Alert Control (p. 394)
•
Limitations of Driver Alert Control
(p. 395)
Activating or deactivating Driver
Alert Control
The Driver Alert Control (DAC) function can
be activated or deactivated.
1. Tap on
Settings
in the centre display's
top view.
2. Select
My Car
IntelliSafe
Driver
Alert Control
.
3. Select or deselect
Alertness Warning
to
activate or deactivate the function.
Related information
•
•
Limitations of Driver Alert Control
(p. 395)
Select rest stop guidance in the
event of a warning from Driver
Alert Control
In cars equipped with Sensus Navigation
*
,
the driver can activate a guide that can auto-
matically suggest an appropriate rest area
when Driver Alert Control (DAC) issues a
warning.
It is possible to select whether the
Rest Stop
Guidance
function should be activated or
deactivated.
1. Tap on
Settings
in the centre display's
top view.
2. Select
My Car
IntelliSafe
Driver
Alert Control
.
3. Select or deselect
Rest Stop Guidance
to activate or deactivate the function.
Related information
•
•
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст