Volvo S90 Twin Engine (2019 year). Instruction — part 9
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
169
Adjusting the door mirrors
To improve visibility to the rear, the door mirrors
need to be adjusted to the driver's height and
seating position. There are several automatic
settings that can also be connected to the mem-
ory function buttons for the power seat*.
Controls used for door mirrors
Door mirror controls.
The joystick in the drivers' door control panel is
used to adjust the position of the door mirrors.
The ignition must be in at least mode I.
1. Press the L button for the left door mirror or
R for the right door mirror. The button will
light up.
2. Adjust the position using the joystick located
between the buttons.
3. Press the L or R button again. The light in
the button will go out.
Automatically folding door mirrors*
The door mirrors can be automatically folded
when driving or parking in tight spaces.
1. Press the L and R buttons at the same time.
2. Release the buttons after about 1 second.
The mirrors will automatically stop when they
are completely folded in.
Open the mirrors by pressing L and R at the
same time. The mirrors will automatically stop
when they are completely open.
Resetting the mirrors' position
A mirror that has been moved out of position
manually (e.g. hit or bumped into) must be electri-
cally returned to its normal position for automatic
folding* to function properly.
1. Fold in the mirrors by pressing the L and R
buttons at the same time.
2. Open them again by pressing the L and R
buttons at the same time.
3. Repeat the above procedure as needed.
The mirrors are now reset to their original posi-
tions.
Tilting when parking
3
The door mirrors can be tilted down to help give
the driver a better view along the sides of the
vehicle, e.g. of the curb when parking.
–
Select reverse gear and press the L or R mir-
ror button.
Please note that the button may need to be
pressed twice depending on settings. When the
door mirror is tilted down, the light in the button
will flash. When reverse gear is engaged, the
door mirrors will automatically start to move after
3 seconds and will reach their original position
after about 8 seconds.
Automatically tilting when parking
3
With this setting, the door mirrors will automati-
cally tilt down when reverse gear is engaged. The
folded position is preset and cannot be adjusted.
To immediately return the door mirrors to their
original position, press the L or R button twice.
1. Tap
Settings
in the center display's Top
view.
2. Tap
My Car
Mirrors and Convenience
.
3. Under
Exterior Mirror Tilt at Reverse
,
select
Off
,
Driver
,
Passenger
or
Both
to
activate/deactivate and to select which mir-
ror to tilt.
3
Only on models equipped with a power driver's seat with memory buttons*.
||
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
170
Automatic folding when the vehicle is
locked*
The door mirrors can automatically fold in when
the vehicle is locked and open when the vehicle
is unlocked using the remote key.
1. Tap
Settings
in the center display's Top
view.
2. Tap
My Car
Mirrors and Convenience
.
3. Select
Fold Mirror When Locked
to acti-
vate/deactivate.
Related information
•
Rearview/door mirrors (p. 167)
•
Adjusting the rearview mirror dimming func-
tion (p. 168)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Activating and deactivating the heated rear
window and door mirrors (p. 218)
Panoramic roof
The panoramic roof is divided into two glass
sections. The front section can be opened verti-
cally at the rear edge (ventilation position) or hor-
izontally (open position). The rear section cannot
be moved.
The panoramic roof has a wind deflector and
sun curtain made of perforated fabric (located
beneath the glass sections) for extra protection
in e.g. bright sunlight.
The panoramic roof and sun curtain are operated
using the controls in the ceiling.
The panoramic roof and sun curtain can also be
operated with the controls in the right-side rear
door.
It can also be operated using keyless opening*
with the door handle.
To operate the panoramic roof and sun curtain,
the ignition must be in mode I or II.
WINDOWS, GLASS AND MIRRORS
}}
* Option/accessory.
171
WARNING
Children, other passengers or objects can be
trapped by the moving parts.
•
Always operate the windows with caution.
•
Do not allow children to play with the
operating controls.
•
Never leave a child alone in the vehicle.
•
Remember to always cut the current to
the power windows by setting the vehi-
cle's electrical system to ignition mode 0
and then taking the remote key with you
when leaving the vehicle.
•
Never stick objects or body parts out
through the windows, even if the vehicle
electrical system is completely turned off.
•
Do not open the panoramic roof when
load carriers are installed.
•
Never place heavy objects on the panor-
amic roof.
•
Remove ice and snow before opening the
panoramic roof. Be careful not to scratch
any surfaces or damage the trim.
•
Do not operate the panoramic roof if it is
frozen in place.
Wind blocker
The panoramic roof is equipped with a wind
blocker that folds up when the roof is open.
Related information
•
Operating the panoramic roof (p. 171)
•
Auto closing the panoramic roof sun curtain
(p. 175)
•
Pinch protection for windows and sun cur-
tains (p. 162)
•
Keyless locking and unlocking* (p. 253)
•
Locking and unlocking using the remote key
(p. 240)
Operating the panoramic roof
The panoramic roof and sun curtain are oper-
ated using a control in the ceiling panel, and
both are equipped with pinch protection.
The control in the right rear door can also be
used for operation.
WARNING
Children, other passengers or objects can be
trapped by the moving parts.
•
Always operate the windows with caution.
•
Do not allow children to play with the
operating controls.
•
Never leave a child alone in the vehicle.
•
Remember to always cut the current to
the power windows by setting the vehi-
cle's electrical system to ignition mode 0
and then taking the remote key with you
when leaving the vehicle.
•
Never stick objects or body parts out
through the windows, even if the vehicle
electrical system is completely turned off.
•
Do not open the panoramic roof when
load carriers are installed.
•
Never place heavy objects on the panor-
amic roof.
||
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
172
•
Remove ice and snow before opening the
panoramic roof. Be careful not to scratch
any surfaces or damage the trim.
•
Do not operate the panoramic roof if it is
frozen in place.
To operate the panoramic roof and sun curtain,
the ignition must be in mode I or II.
It can also be operated using keyless opening*
with the door handle.
WARNING
Make sure that no child or other passenger
comes into contact with the windows as they
are closing with keyless closing*.
Check that the panoramic roof is properly
closed when closing.
The movement of the roof will stop if the control
is released during manual operation or when the
glass has reached the fully open/closed position.
The movement of both the panoramic roof and
the sun curtain is also stopped if the control in
the ceiling is operated again in the direction
opposite that of the current direction of move-
ment. Movement will also stop if the control in the
right rear door is moved again in any direction.
The panoramic roof and sun curtain are also
equipped with pinch protection. If there is any
problem with the pinch protection, a rest proce-
dure can be tested.
For manual opening, the sun curtain must be
completely open before the panoramic roof
can be opened. For the reverse procedure,
the panoramic roof must be completely
closed before the sun curtain can be com-
pletely closed.
Opening and closing ventilation
position
Ventilation position, rear edge raised.
Open by pushing the control upward once.
Close by pushing the control downward
once.
When ventilation mode is selected, the rear edge
of the front section of the roof is raised. If the sun
curtain is fully closed when ventilation position is
selected, it will automatically open approx. 50 mm
(approx. 2 inches).
If the panoramic roof is closed from the ventila-
tion position, the sun curtain will also automati-
cally close.
WINDOWS, GLASS AND MIRRORS
}}
173
If the roof is closed using the control in the
right rear door, the sun curtain must be
closed separately.
Fully opening and closing the
panoramic roof with the control in the
ceiling
Operation, manual mode
Operation, automatic mode
Manual operation
1. To open the sun curtain, pull the control
backward to the manual open mode.
2. To open the panoramic roof, pull the control
backward a second time to the manual open-
ing position.
Close by repeating the above procedure in
reverse - push the control forward/down to the
manual closing position.
Auto operation
1. To open the sun curtain to the fully open
position, pull the control backward to the
auto open mode and release.
2. To open the panoramic roof, pull the control
backward a second time to the automatic
opening position and release.
Close by repeating the above procedure in
reverse - push the control forward/down to the
auto close position.
Automatic operation - rapid opening or
closing
The panoramic roof and sun curtain can be
opened or closed simultaneously:
–
Open - press the control backward twice to
the automatic operation position and release.
–
Close - press the control forward/down twice
to the automatic operation position and
release.
Operating with right-side rear door
controls
Sun curtain control.
Operation, manual mode
Operation, automatic mode
||
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
174
Panoramic roof control.
Operation, manual mode
Operation, automatic mode
Manual operation
1. To open the panoramic roof to the ventilation
position, move the panoramic roof control
downward to the manual opening position.
2. To open the sun curtain, move the sun cur-
tain control downward to the manual open
position.
3. To open the panoramic roof fully, move the
panoramic roof control downward a second
time to the manual operation position.
To close, pull up the respective control to the
manual closing position.
Auto operation
1. To open to the ventilation position, move the
panoramic roof control downward to the auto
open position and release.
2. To open to the sun curtain, move the sun
curtain control downward to the auto open
position and release.
3. To open the panoramic roof, move the panor-
amic roof control downward a second time to
the auto open position and release.
To close, pull up the respective control to the
automatic closing position.
Automatic operation - rapid opening and
closing
The panoramic roof and sun curtain can be
opened or closed simultaneously.
1. To open to the ventilation position, move the
panoramic roof control downward to the auto
position and release.
2. To open fully, move the sun curtain control
downward to the auto position and release.
Then immediately move the panoramic roof
control downward to the auto position and
release.
–
To close, pull up the panoramic roof control
to the auto position and release. Then imme-
diately move the sun curtain control up to the
auto position and release.
Related information
•
•
Auto closing the panoramic roof sun curtain
(p. 175)
•
Pinch protection for windows and sun cur-
tains (p. 162)
•
Keyless locking and unlocking* (p. 253)
•
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
175
Auto closing the panoramic roof
sun curtain
With this function, the sun curtain closes auto-
matically 15 minutes after the car has been
locked if it is parked in hot weather. This is done
to lower the passenger compartment tempera-
ture and protect the upholstery against being
bleached by the sun.
The function is deactivated as the default factory
setting and can be activated or deactivated using
the center display.
1. Tap
Settings
in the Top view in the center
display.
2. Tap
My Car
Locking
.
Select
Auto Close Sunroof Curtain
to
activate/deactivate.
The sun curtain also closes when all windows
are closed with keyless closing*.
Related information
•
•
Operating the panoramic roof (p. 171)
•
Pinch protection for windows and sun cur-
tains (p. 162)
•
Keyless locking and unlocking* (p. 253)
•
Locking and unlocking using the remote key
(p. 240)
Wiper blades and washer fluid
The wipers and the washer fluid are used to
improve visibility and the headlight pattern.
The washer nozzles are heated* automatically in
cold weather to prevent the washer fluid from
freezing.
When there is approximately 1 liter (1 qt) of
washer fluid remaining, a message to refill will
appear in the instrument panel.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight washers
(p. 178)
•
Using the rain sensor's memory function
(p. 177)
•
•
Windshield wipers in the service position
(p. 634)
•
Replacing windshield wiper blades (p. 633)
•
WINDOWS, GLASS AND MIRRORS
176
Using the windshield wipers
The windshield wipers clean the windshield. The
right-side steering wheel lever is used to adjust
windshield wiper settings.
Right-hand steering wheel lever.
Thumb wheel, used to set rain sensor sensi-
tivity and interval wiper speed.
Single sweep
Move the lever down and release for a
single sweep.
Wipers off
Move the lever to position 0 to turn off
the windshield wipers.
Interval wipers
Set the number of sweeps per time unit
with the thumb wheel when interval wip-
ers are selected.
Continuous wipers
Move the lever upward for the wipers to
operate at normal speed.
Move the lever upward again for the wip-
ers to operate at high speed.
Before activating the wipers, make sure that
the wiper blades are not frozen in place and
that any snow or ice on the windshield has
been scraped away.
Use plenty of washer fluid when the wipers
clean the windshield. The windshield must be
wet when the windshield wipers are working.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight washers
(p. 178)
•
Wiper blades and washer fluid (p. 175)
•
Using the rain sensor's memory function
(p. 177)
•
•
Windshield wipers in the service position
(p. 634)
•
Replacing windshield wiper blades (p. 633)
Using the rain sensor
The rain sensor monitors the amount of water on
the windshield and automatically starts the wind-
shield wipers. Rain sensor sensitivity can be
adjusted using the thumb wheel on the right-
hand steering wheel lever.
Right-hand steering wheel lever.
Rain sensor button
Thumb wheel, sensitivity/interval wiper speed
When the rain sensor is activated, the
rain
sensor symbol will be displayed in the instrument
panel.
Activating the rain sensor
When the rain sensor is activated, the engine
must be running or the ignition must be in mode I
or II. The windshield wiper lever must also be in
position 0 or in the single sweep position.
WINDOWS, GLASS AND MIRRORS
177
Activate the rain sensor by pressing the rain sen-
sor button
.
If the lever is pressed down, the wipers will make
additional sweeps across the windshield.
Turn the thumb wheel upward for increased sen-
sitivity and downward for decreased sensitivity.
The wipers will make one extra sweep when the
thumb wheel is turned upward.
Deactivate the rain sensor
Deactivate the rain sensor by pressing the
rain sensor button or moving the lever upward to
another wiper mode.
The rain sensor is automatically deactivated in
ignition mode 0 or when the engine is switched
off.
The rain sensor is also automatically deactivated
when the wiper blades are put in the service
position. The rain sensor will reactivate when
service mode is switched off.
The windshield wipers may start inadvertently
and be damaged in automatic car washes.
Deactivate the rain sensor when the engine is
running or when the ignition is in mode I or II.
The symbol in the instrument panel will go
out.
Related information
•
Using the windshield and headlight washers
(p. 178)
•
Wiper blades and washer fluid (p. 175)
•
Using the rain sensor's memory function
(p. 177)
•
•
Windshield wipers in the service position
(p. 634)
•
Replacing windshield wiper blades (p. 633)
•
Using the windshield wipers (p. 176)
Using the rain sensor's memory
function
The rain sensor monitors the amount of water on
the windshield and automatically starts the wind-
shield wipers.
Activating/deactivating memory
function
The rain sensor's memory function can be set to
activate so that the rain sensor button does not
need to be pressed each time the engine is
started:
1. Tap
Settings
in the Top view in the center
display.
2. Tap
My Car
Wipers
.
3. Select
Rain Sensor Memory
to activate/
deactivate the memory function.
Related information
•
Using the rain sensor (p. 176)
•
Using the windshield and headlight washers
(p. 178)
•
Wiper blades and washer fluid (p. 175)
•
•
Windshield wipers in the service position
(p. 634)
•
Replacing windshield wiper blades (p. 633)
•
WINDOWS, GLASS AND MIRRORS
* Option/accessory.
178
Using the windshield and headlight
washers
The windshield and headlight washers clean the
windshield and headlights. Use the right-side
steering wheel lever to start the windshield and
headlight washers.
Starting the windshield and headlight
washers
Washing function, right-hand steering wheel lever.
–
Move the right-hand steering wheel lever
toward the steering wheel to start the wind-
shield and headlight washers.
> After the lever is released, the wipers
make several extra sweeps.
Avoid activating the washer system when it is
frozen or the fluid reservoir is empty. Other-
wise, there is a risk of damaging the pump.
Headlight washer*
To save washer fluid, the headlights are washed
automatically according to a defined interval
when the headlights are on.
Reduced washing
When there is about 1 liter (1 qt) of washer fluid
left in the reservoir and the
Washer fluid
Level
low, refill
message is displayed in the instrument
panel together with the
symbol, the washer
fluid supply to the headlights is cut off. This is to
prioritize windshield cleaning and visibility
through it. The headlights are only washed if high
or low beam is on.
Related information
•
Using the rain sensor (p. 176)
•
Wiper blades and washer fluid (p. 175)
•
Using the rain sensor's memory function
(p. 177)
•
•
Windshield wipers in the service position
(p. 634)
•
Replacing windshield wiper blades (p. 633)
•
SEATS AND STEERING WHEEL
* Option/accessory.
180
Manual front seats
The power front seats can be adjusted in a num-
ber of different ways for optimal comfort and
ergonomics.
Raise/lower the front edge of the seat cush-
ion* by moving the control up/down.
1
Change the length of the seat cushion* by
pulling up the lever and moving the cushion
forward/backward.
Move the seat forward/backing by lifting the
handle and moving the seat to a suitable dis-
tance from the steering wheel and pedals.
Check to make sure the seat is securely
locked into place after its setting has been
changed.
Adjust lumbar support by pressing the button
up/down/forward/rearward
2
.
Raise/lower the seat by moving the control
up/down.
Change the backrest tilt by turning the knob
on the backrest.
WARNING
•
Do not adjust the seat while driving. The
seat should be adjusted so that the brake
pedal can be depressed fully. In addition,
position the seat as far rearward as com-
fort and control allow.
•
Check that the seat is securely locked
into position after adjusting.
Related information
•
•
Adjusting the power* front seats (p. 181)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
1
Only applies to the driver's seat.
2
Applies for four-way lumbar support*. Two-way lumbar support* is adjusted forward/rearward.
SEATS AND STEERING WHEEL
}}
* Option/accessory.
181
Power* front seats
The power front seats can be adjusted in a num-
ber of different ways for optimal comfort and
ergonomics. The power seat can be moved for-
ward/backward and up/down. The height and
length* of the seat cushion and the tilt of the
backrest can be adjusted. Lumbar support* can
be adjusted up, down, forward and backward
3
.
The power seats can be adjusted for a certain
period of time after the door is unlocked without
the engine running. The seats can always be
adjusted while the engine is running. They can
also be adjusted for a short period after the
engine is turned off.
The power seats have an overload protector
that is triggered if a seat is blocked by any
object. If this occurs, remove the object and
attempt to adjust the seat again.
Related information
•
•
Adjusting the power* front seats (p. 181)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
Adjusting the power* front seats
Set the desired seating position using the con-
trols on the front seat cushion. To set the con-
venience functions, turn the multifunction con-
trol
4
upward/downward.
The illustration shows the controls in a vehicle with four-
way lumbar support*. Vehicles with two-way lumbar sup-
port* do not have the rotary multifunction control.
In vehicles with four-way lumbar support*,
turn the multifunction control
4
up/down to
set the convenience functions. In vehicles
with two-way lumbar support*, use the round
button to adjust the lumbar support forward/
rearward.
Raise/lower the front edge of the seat cush-
ion by moving the control up/down.
3
Applies for four-way lumbar support*. Two-way lumbar support* is adjusted forward/rearward.
||
SEATS AND STEERING WHEEL
* Option/accessory.
182
Raise/lower the seat by moving the control
up/down.
Move the seat forward/rearward by moving
the control forward/rearward.
Change the backrest tilt by moving the con-
trol forward/backward.
Only one movement (forward/rearward/up/
down) can be performed at a time.
The front seat backrests cannot be folded down
completely.
Related information
•
•
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
Storing positions for seats, mirrors
and head-up display*
Adjustment settings for the power* seat, door
mirrors and head-up display* can be stored in
the memory buttons.
Two different positions for the power* seat, door
mirrors and head-up display* can be stored using
the memory buttons. The buttons are located on
the inside of either one or both* front doors.
Button M for storing a setting
Memory button
Memory button
Storing positions
1. Adjust the seat, door mirrors and head-up
display to the desired position.
2. Press and hold the M button. The indicator
light in the button will illuminate.
3. Within three seconds, press and hold the 1
or 2 button.
> When the position has been stored in the
memory button, an audio signal will sound
and the indicator light in the M button will
go out.
If none of the memory buttons are pressed within
three seconds, the M button will go out and no
position will be stored.
The seats, door mirrors or head-up display must
be readjusted before a new memory position can
be set.
Related information
•
•
•
Adjusting the power* front seats (p. 181)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
4
Not available in vehicles with two-way lumbar support*.
SEATS AND STEERING WHEEL
}}
* Option/accessory.
183
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
•
Adjusting the door mirrors (p. 169)
•
Head-up display settings* (p. 140)
Using stored positions for seats,
mirrors and head-up display*
If the positions for the power* seat, door mirrors
and head-up display* have been stored, they can
be easily activated using the memory buttons.
Using a stored position
A stored position can be used with the front door
open or closed:
Front door open
–
Briefly press one of the memory buttons 1
(
) or 2 (
). The power seats, door mirrors
and head-up display will move and stop at
the positions stored in that button.
Front door closed
–
Press and hold one of the memory buttons 1
(
) or 2 (
) until the seat, door mirrors
and head-up display stop in the positions
stored in that memory button.
If the memory button is released, the seat, door
mirrors and head-up display will stop moving.
WARNING
•
This list point needs to be translated
exactly to: "Because the driver's seat can
be adjusted with the ignition off, children
should never be left unattended in the
vehicle.
•
Movement of the seat can be STOPPED
at any time by pressing any button on the
power seat control panel.
•
Do not adjust the seat while driving.
•
The seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rearward
as comfort and control allow.
•
The seat rails on the floor must not be
obstructed in any way when the seat is in
motion.
Related information
•
•
SEATS AND STEERING WHEEL
* Option/accessory.
184
•
Adjusting the power* front seats (p. 181)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
•
Adjusting the door mirrors (p. 169)
•
Head-up display settings* (p. 140)
Front seat massage* settings
The settings for the multifunctional seats can be
adjusted using either the mutifunction control on
the seat or the center display. The adjustment
settings are shown in the center display.
Multifunction control, located on the side of the seat
cushion.
Massage settings
The following massage settings are available:
•
On
/
Off
: Select
On
/
Off
to turn on/off the
massage function.
•
Programs 1-5
: There are 5 preset massage
programs. Select
Swell
,
Tread
,
Advanced
,
Lumbar
or
Shoulder
.
•
Intensity
: Select
Low
,
Normal
or
High
.
•
Speed
: Select
Slow
,
Normal
or
Fast
.
Restarting the massage function
The massage function turns off automatically
after 20 minutes. The function is reactivated
manually.
–
Tap
Restart
, which is displayed in the center
display, to restart the selected massage pro-
gram.
> The massage program will restart. If no
selection is made, the message will be
stored in Top view.
Related information
•
•
•
Adjusting the power* front seats (p. 181)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting front seat massage settings*
(p. 185)
•
Adjusting* front seat cushion length (p. 185)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
SEATS AND STEERING WHEEL
}}
* Option/accessory.
185
Adjusting front seat massage
settings*
The settings for the multifunctional seats can be
adjusted using either the mutifunction control on
the seat or the center display. The adjustment
settings are shown in the center display.
Adjusting front seat massage settings
The front seat backrests have a massage func-
tion. Air-filled cushions provide the massaging
action and a number of settings are available.
The massage function can only be activated
when the engine is running.
1. Activate the multifunction control by turning
the control
upward/downward. The seat
settings view will appear in the center dis-
play.
2. Select
Massage
in the seat settings view.
3. Select massage settings by tapping the cen-
ter display or by moving the cursor up/down
using the multifunction control's upper
/
lower
buttons. Change a setting in the
selected function by tapping the arrows on
the center display or by using the multifunc-
tion control's front
/rear
buttons.
Related information
•
•
•
Adjusting the power* front seats (p. 181)
•
Storing positions for seats, mirrors and head-
up display* (p. 182)
•
Using stored positions for seats, mirrors and
head-up display* (p. 183)
•
Adjusting* front seat cushion length (p. 185)
•
Front seat massage* settings (p. 184)
•
Adjusting front seat side bolster settings*
(p. 186)
•
Adjusting front seat lumbar support* (p. 187)
•
Adjusting the passenger seat from the driv-
er's seat* (p. 188)
Adjusting* front seat cushion length
Depending on the selected equipment level, the
length of the seat cushion can either be
adjusted using the multifunction control* on the
side of the seat cushion, or manually adjusted
using the control on the front of the seat cush-
ion.
Adjusting seat cushion length using the
multifunction control
The multifunction control, located on the side of the seat
cushion.
1. Activate the multifunction control by turning
the control
upward/downward. The seat
settings view will appear in the center dis-
play.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст