Audi TT (2007 year). Manual — part 15
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
♦ Engine support bracket (supplementary set) -T40093-
dles on bolted flanges of wing panels as shown in illustration.
– Attach hook of spindle to engine lifting eye (left-side).
WARNING
Risk of accident because of loose bolt connections.
♦ Screw on flange nut or nut with washer -arrow- at least 6
turns to ensure that eye-head bolt -3368- is properly se‐
cured.
– Secure eye-head bolt -3368- with flange nut M10 or nut with
washer to engine support as shown in illustration.
– Attach spindle -10 - 222 A /11- (right-side) to eye-head bolt
-3368- .
– Take up weight of engine evenly with both spindles (but do not
raise engine).
1. Cylinder block (pulley end)
51
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove bolts -arrows-.
– Detach electrical connector at coolant shortage indicator
switch -F66- and move coolant expansion tank to side.
– Remove bolts -1- and -2- and remove connecting bracket.
– Remove bolts -3 ... 6- and detach engine mounting.
– Remove bolt -3- on engine support.
Note
Disregard -items 1, 2-.
– Remove bolt -arrow-.
– Remove bolts -1- and -2- and remove idler rollers for toothed
belt.
52
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove bolts -1 ... 6- and detach bracket for ancillaries.
Installing
Installation is carried out in the reverse order; note the following:
Note
Renew bolts securing bracket for ancillaries.
– Check that dowel sleeve at top right between bracket for an‐
cillaries and cylinder block is fitted; insert dowel sleeve if
necessary.
– Tighten bolts for bracket for ancillaries
.
– Install engine support and engine mounting
.
1.8
Sealing flange (pulley end) - exploded view
1 - Bolt
❑ Tightening torque
2 - Crankshaft sprocket
❑ Contact surface be‐
tween sprocket and
crankshaft must be free
of oil
❑ Can only be installed in
one position
3 - Oil seal for crankshaft (pul‐
ley end)
❑ Renewing
❑ Do not lubricate with oil
4 - Sealing flange (pulley end)
❑ Should be positioned on
dowel pins
❑ Removing and installing
5 - Cylinder block
6 - Dowel pin
❑ 2x
7 - Bolt
❑ Tightening torque and
1. Cylinder block (pulley end)
53
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Sealing flange (pulley end) - tightening torque and sequence
– Tighten bolts for sealing flange on pulley end -1 ... 10- in three
stages as follows:
1.
Screw in bolts -1 ... 10- by hand until they make contact.
2.
Tighten bolts -1 ... 6- in diagonal sequence and in stages
to 15 Nm.
3.
Tighten bolts -7 ... 10- to 15 Nm.
1.9
Renewing crankshaft oil seal (pulley
end)
Special tools and workshop equipment required
♦ Oil seal extractor -3203-
♦ Counterhold tool -3415-
♦ Assembly tool -T10053-
54
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст