Ford Excursion (2005 year). Manual — part 26

Removing the third row seat
From the rear of the vehicle, with the liftgate window and cargo doors
open:

1. Pull the seat release lever located
on the lower right side of the
seatback while pushing the seatback
down onto the seat cushion.
• The seatback will latch onto the

cushion.

2. Lift the seat release bar located
at the center of the seat near the
floor to release the floor latches.

3. While pulling up on the release
bar, lift the seat up and out of the floor tubs and roll seat rearward.
4. With assistance, lift the seat out of the vehicle.
Installing the third row seat

Always latch the vehicle seat to the floor, whether the seat is
occupied or empty. If not latched, the seat may cause injury

during a sudden stop.

When reinstalling a rear seat in your vehicle it must be placed in
its original position. Improper installation of the seat will prevent

correct use of the safety belts and could increase the risk of injury.
Refer to the warning label on the seat belt.

For proper latching, ensure that the
floor tubs are clear of debris.

From the rear of the vehicle, with
the liftgate open:

1. With assistance, lift the seat into
the rear of the vehicle. Roll the seat
forward and guide the front locators
over the seat locator pins of the front floor tubs.
• When the rear of the seat is 4–5 in (10–13 cm) above the rear pins,

let the seat drop. This will ensure that the seat will properly latch into
the floor.

2. Push up on the seat to verify that it is latched into the floor.

Seating and Safety Restraints

106

3. Verify that the safety belts can move freely on either side of the seat.

4. Lift the lever and pull up the seatback to drive position.

SAFETY RESTRAINTS

Safety restraints precautions

Always drive and ride with your seatback upright and the lap
belt snug and low across the hips.

To reduce the risk of injury, make sure children sit in the back
seat where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the
vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

It is extremely dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to
ride in any area of your vehicle that is not equipped with seats and
safety belts. Be sure everyone in your vehicle is in a seat and using a
safety belt properly.

In a rollover crash, an unbelted person is significantly more likely
to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt
assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the
outside shoulder only. Never wear the shoulder belt under the arm. 2)
Never swing the safety belt around your neck over the inside shoulder.
3) Never use a single belt for more than one person.

Seating and Safety Restraints

107

Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.

Safety belts and seats can become hot in a vehicle that has been
closed up in sunny weather; they could burn a small child. Check

seat covers and buckles before you place a child anywhere near them.

Combination lap and shoulder belts

1. Insert the belt tongue into the
proper buckle (the buckle closest to
the direction the tongue is coming
from) until you hear a snap and feel
it latch. Make sure the tongue is
securely fastened in the buckle.

2. To unfasten, push the release
button and remove the tongue from
the buckle.

The front outboard and rear outboard safety restraints in the vehicle are
combination lap and shoulder belts. The front outboard passenger and
rear seat outboard safety belts have two types of locking modes
described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows free shoulder belt length
adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of approximately 5 mph

Seating and Safety Restraints

108

(8 km/h) or more, the combination safety belts will lock to help reduce
forward movement of the driver and passengers.

Automatic locking mode

When to use the automatic locking mode

In this mode, the shoulder belt is automatically pre-locked. The belt will
still retract to remove any slack in the shoulder belt. The automatic
locking mode is not available on the driver safety belt.

This mode should be used any time a child safety seat is installed in a
passenger front or outboard rear seating position (if equipped). Children
12 years old and under should be properly restrained in the rear seat
whenever possible. Refer to Safety restraints for children or Safety
seats for children later in this chapter.

How to use the automatic locking mode
• Buckle the combination lap and

shoulder belt.

• Grasp the shoulder portion and

pull downward until the entire
belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking

sound. This indicates the safety belt is now in the automatic locking
mode.

Seating and Safety Restraints

109