Ford Thunderbird (2004 year). Manual — part 10
Increasing speed while using speed control
There are two ways to set a higher
speed:
• Press and hold the SET + control
until you get to the desired
speed, then release the control.
You can also use the SET +
control to operate the Tap-Up
function. Press and release this
control to increase the vehicle set
speed in small amounts by 1.6
km/h (1 mph).
• Use the accelerator pedal to get to the desired speed. When the
vehicle reaches that speed press and release the SET + control.
Reducing speed while using speed control
There are two ways to reduce a set
speed:
• Press and hold the SET - control
until you get to the desired
speed, then release the control.
You can also use the SET -
control to operate the Tap-Down
function. Press and release this
control to decrease the vehicle
set speed in small amounts by
1.6 km/h (1 mph).
• Depress the brake pedal or
CANCEL until the desired vehicle
speed is reached, press the SET
+ control.
Driver Controls
44
Turning off speed control
There are two ways to turn off the speed control:
• Depress the brake pedal or press
CANCEL. This will not erase your
vehicle’s previously set speed.
• Press the speed control OFF
control.
Note: When you turn off the speed
control or the ignition, your speed
control set speed memory is erased.
STEERING WHEEL CONTROLS
These controls allow you to operate some audio control features.
Audio control features
Press MEDIA to select AM, FM1,
FM2, or CD.
In AM, FM1, or FM2 mode:
• Press ⌬ or ⵜ to select preset
stations within the selected radio
band.
In CD mode:
• Press ⌬ or ⵜ to select the next
selection on the CD.
O
N
O
F
F
RES
SET
CANCEL
MUTE
VOL
MEDIA
MUTE
VOL
MEDIA
Driver Controls
45
In any mode:
• Press VOL + or − to adjust
volume.
Press the PHONE/MUTE control to
mute the playing media. Press again
to return to the playing media.
HOMELINK
姞 WIRELESS CONTROL SYSTEM
The HomeLink
威 Wireless Control System, located on the header trim,
provides a convenient way to replace up to three hand-held transmitters
with a single built-in device. This feature will learn the radio frequency
codes of most current transmitters to operate garage doors, entry gate
operators, security systems, entry door locks, and home or office lighting.
When programming your HomeLink
威 Wireless Control System to
a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLink
威 Wireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink
威 at: www.homelink.com or 1–800–355–3515.
MUTE
VOL
MEDIA
MUTE
VOL
MEDIA
Driver Controls
46
Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink
威 equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink
威 buttons be erased for security purposes, refer to
Programming in this section.
Programming
Do not program HomeLink
威 with the vehicle parked in the garage.
Note: Some vehicles may require the ignition switch to be turned to the
second (or “ACC”) position for programming and/or operation of the
HomeLink
威. It is also recommended that a new battery be placed in the
hand-held transmitter of the device being programmed to HomeLink
威 for
quicker training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the
amber light begins to flash after 20
seconds. Do not repeat step one to
program additional hand-held
transmitters to the remaining two
HomeLink
威 buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink
威.
2. Position the end of your hand-held transmitter 2–8 cm (1–3 inches)
away from the HomeLink
威 button you wish to program (located on the
header trim) while keeping the amber light in view.
3. Simultaneously press and hold
both the HomeLink
威 and hand-held
transmitter button. Do not release
the buttons until step 4 has been
completed.
Some entry gates and garage door
openers may require you to replace
step 3 with procedures noted in the
“Gate Operator and Canadian Programming” section for Canadian
residents.
4. The amber light will flash slowly and then rapidly. Release both
buttons when the amber light flashes rapidly. (The rapid flashing light
indicates acceptance of the hand-held transmitters’ radio frequency
signals.)
Driver Controls
47
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст