Ford GT (2018 year). Manual — part 27

If Your Vehicle Gets Stuck In Mud
or Snow

If your vehicle is stuck in mud or snow,
reducing the stability and traction control
may be beneficial as this allows the wheels
to spin. You can reduce the stability and
traction control by switching to Sport
mode and adjusting the AdvanceTrac
setting. See Using Stability Control
(page 116).

GENERAL INFORMATION

Note: Occasional brake noise is normal. If
a metal-to-metal, continuous grinding or
continuous squeal sound is present, the
brake linings may be worn-out. Have the
system checked by an authorized dealer. If
your vehicle has continuous vibration or
shudder in the steering wheel while braking,
have it checked by an authorized dealer.

Note: Brake dust may accumulate on the
wheels, even under normal driving
conditions. Some dust is inevitable as the
brakes wear and does not contribute to
brake noise. See Cleaning the Wheels
(page 177).

E138644

See Warning Lamps and
Indicators (page 65).

Wet brakes result in reduced braking
efficiency. Gently press the brake pedal a
few times after washing the car.

Carbon Ceramic Brake Discs

Your vehicle has carbon ceramic brake
discs. When cleaning your wheels and tires,
use care not to get any wheel cleaner or
tire dressing on the brake discs.

E269429

This lamp illuminates when your
brakes pads are worn and
require replacement. See an

authorized dealer for replacement.

Brake Over Accelerator

In the event the accelerator pedal
becomes stuck or entrapped, apply steady
and firm pressure to the brake pedal to
slow the vehicle and reduce engine power.
If you experience this condition, apply the
brakes and bring your vehicle to a safe

stop. Move the transmission to park (P),
switch the engine off and apply the parking
brake. Inspect the accelerator pedal for
any interferences. If none are found and
the condition persists, have your vehicle
towed to the nearest authorized dealer.

Brake Assist

Brake assist detects when you brake
rapidly by measuring the rate at which you
press the brake pedal. It provides
maximum braking efficiency as long as you
press the pedal, and can reduce stopping
distances in critical situations.

Anti-lock Brake System

This system helps you maintain steering
control during emergency stops by keeping
the brakes from locking.

This lamp momentarily
illuminates when you switch the
ignition on. If the light does not

illuminate during start up, remains on or
flashes, the system may be disabled. Have
the system checked by an authorized
dealer. If the anti-lock brake system is
disabled, normal braking is still effective.

E269429

If the brake warning lamp
remains illuminated after you
release the parking brake, have

the system checked by an authorized
dealer.

HINTS ON DRIVING WITH
ANTI-LOCK BRAKES

The anti-lock braking system does not
eliminate the risks when:
•

You drive too closely to the vehicle in
front of you.

•

Your vehicle is hydroplaning.

•

You take corners too fast.

•

The road surface is poor.

Note: If the system activates, the brake
pedal may pulse and may travel further.
Maintain pressure on the brake pedal. You
may also hear a noise from the system. This
is normal.

ELECTRIC PARKING BRAKE

WARNING

Always set the parking brake and
leave your vehicle with the
transmission in park (P).

The electric parking brake operates with
the switch in the center console.

Note: When you apply the electric parking
brake in certain conditions, for example, on
a steep hill, the electric parking brake may
reapply the brakes within three to ten
minutes.

Note: You may notice various noises when
you apply and release the electric parking
brake. This is normal and no cause for
concern.

Applying the Electric Parking
brake

WARNINGS

Applying the electric parking brake
while moving will result in the
engagement of the anti-lock braking

system. Do not use the electric parking
brake system when the vehicle is moving
unless the normal brake system is unable
to stop the vehicle.

With the exception of emergency
conditions (for example, the brake
pedal is broken or is blocked), do not

apply the electric parking brake while the
vehicle is moving. On bends, or poor road
surfaces or weather conditions, emergency
braking can cause the vehicle to skid out
of control or off the road.

Note: The brake system warning lamp
lights during an electric parking brake apply.
If the brake system warning lamp flashes
and continues to flash, there could be a
problem with your electric parking brake.
See your authorized dealer.

Note: The brake system warning lamp
illuminates for ten seconds if you switch the
ignition off after you apply the electric
parking brake, or you apply the electric
parking brake after you switch the ignition
off.

Note: When you switch the engine off, the
electric parking brake applies.

E227395

Pull the switch up to apply the electric
parking brake.

The brake system warning lamp flashes
for about two seconds and then
illuminates to confirm that you have
applied the electric parking brake. See
Information Displays (page 70).

If you apply the electric parking brake when
your vehicle is moving, the brake system
warning lamp illuminates and a warning
chime sounds. See Information Displays
(page 70).

If your vehicle speed is above 4 mph
(6 km/h), the braking force is applied as
long as you pull the switch. Releasing or
pressing the switch or pressing the
accelerator pedal will stop the braking
force.

Releasing the Electric Parking
Brake

E227515

You can release the electric parking brake
either manually by pressing the switch or
automatically by pressing the accelerator
pedal.

Manual release

WARNING

If the brake system warning light
remains illuminated or flashes for
more than four seconds after you

have released the parking brake, there
could be a problem with your braking
system. Have your vehicle checked as soon
as possible.

You can manually release the electric
parking brake by:

1.

Switching the ignition on.

2. Pressing the brake pedal.

3. Pressing the electric parking brake

switch.

When you release the electric parking
brake, the brake system warning lamp
turns off.

Automatic release - drive away release

Your vehicle automatically releases the
parking brake if all of the following
conditions exist:
•

You close the driver door.

•

You put on your seatbelt.

•

You press the accelerator pedal.

•

The system does not detect any faults
in the parking brake system.

Note: If the electric parking brake warning
lamp stays illuminated, the electric parking
brake will not automatically release. You
must release the electric parking brake using
the electric parking brake switch.

The brake system warning lamp turns off
to confirm that you released the electric
parking brake.

Note: The electric parking brake drive away
release makes starting on a hill easier. This
feature releases the parking brake
automatically when the vehicle has
sufficient drive force to move up the hill. To
assure drive away release when starting
uphill, press the accelerator pedal quickly.

Battery With No Charge

WARNING

You will not be able to apply or
release the electric parking brake if
the battery is low or has no charge.

If the battery is low or has no charge, use
jumper cables and a booster battery.

After connecting the booster battery, you
should be able to apply or release the
electric parking brake.