Ford Focus RS (2011 year). Instruction — part 36
Vehicles with heated windshield
Panel and Console, Removal and Installation).
12.
E72736
13.
E119480
All vehicles
14.
Use a suitable awl to thread the cutting wire.
General Equipment: Direct Glazing
Removal/Replacement Equipment
G1226165en
501-11-
57
Glass, Frames and Mechanisms
501-11-
57
REMOVAL AND INSTALLATION
11.
Refer to: Overhead Console
(501-12 Instrument
E113701
15.
CAUTION: If the original window glass
is to be installed, take care not to
damage the electrical connectors and
the weatherstrip (if equipped).
Use a suitable brace to prevent trim damages.
General Equipment: Direct Glazing
Removal/Replacement Equipment
G1226165en
501-11-
58
Glass, Frames and Mechanisms
501-11-
58
REMOVAL AND INSTALLATION
E113702
x2
16. NOTE: Note the position of each glass locating
spacer.
E78708
Installation
1.
NOTE: Minimum 1 mm bead thickness.
General Equipment: Knife
1.
2. NOTE: Make sure that the mating faces are
clean and free of foreign material.
3. NOTE: Touching the adhesive surface will
impair rebonding.
Prepare the windshield glass, windshield
glass flange and trimmed PU adhesive in
accordance with the instructions supplied
with the glass adhesive kit.
E114059
1
2
G1226165en
501-11-
59
Glass, Frames and Mechanisms
501-11-
59
REMOVAL AND INSTALLATION
2. NOTE: Make sure that new components are
installed.
E78708
3. Apply the activator/ primer in accordance with
the instructions supplied with the glass adhesive
kit.
E114060
G1226165en
501-11-
60
Glass, Frames and Mechanisms
501-11-
60
REMOVAL AND INSTALLATION
4. Apply the activator/ primer in accordance with
the instructions supplied with the glass adhesive
kit.
E114061
5. NOTE: Discard the first 100 mm of adhesive as
this may have a reduced working time.
NOTE: Make sure that any breakage in the
continuous bead of adhesive is overlapped by
20 mm.
General Equipment: Direct Glazing
Removal/Replacement Equipment
Material: Windshield Adhesive Kit
(WSS-M11P57-A5)
Material: Windscreen Adhesive Kit - 1
Component (WSK-M11P57-A3 /
7U7J-T03863-AA)
E103487
8-10mm
6.
Press firmly and evenly into position.
General Equipment: Direct Glazing
Removal/Replacement Equipment
•
•
CAUTION: During the curing time of
the polyurethane (PU) adhesive, the
door windows must be left open.
Using tape, secure the windshield glass in
the correct position until the PU adhesive has
cured.
General Equipment: Adhesive Tape
G1226165en
501-11-
61
Glass, Frames and Mechanisms
501-11-
61
REMOVAL AND INSTALLATION
E88280
x2
Vehicles with heated windshield
7.
G1226165en
501-11-
62
Glass, Frames and Mechanisms
501-11-
62
REMOVAL AND INSTALLATION
E119480
8. Torque: 12 Nm
E72736
Panel and Console, Removal and Installation).
10.
E103504
x2
x2
G1226165en
501-11-
63
Glass, Frames and Mechanisms
501-11-
63
REMOVAL AND INSTALLATION
9.
Refer to: Overhead Console
(501-12 Instrument
Vehicles with autolamps and rain sensor
11.
E103501
12.
E103426
13.
E103425
Vehicles with manual dimming interior mirror
14.
E103502
G1226165en
501-11-
64
Glass, Frames and Mechanisms
501-11-
64
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст