Ford Focus RS (2011 year). Instruction — part 147
Item 5
Front lower arm retaining bolts
1. Fabricate two 20 mm wide by 113 mm long
spacers.
TIE0004698
2.
CAUTION: Both sides of the suspension
must be set to the design height setting.
Using
two transmission jacks and wooden
blocks,
raise the suspension to the design
height
setting on both sides.
•
Position the transmission jack and the
wooden block as shown.
TIE0024959
3. NOTE: The spacer must be positioned
exactly as shown.
Install the spacer on both sides.
1. Remove the bump stop.
2. Install the spacer between the rear lower arm
and the rear axle crossmember making sure
that the spacer is in a vertical plane.
TIE0014145
2
1
Item 6
Front lower arm
CAUTION: The front lower arms are marked
FRONT. Make a note of the position of the
front lower arms to aid installation.
Item 7
Upper arm retaining bolts
NOTE: Make a note of the position of the upper
arms to aid installation.
Item 9
Rear lower arm adjustment cam nut
1. Mark the position of the rear lower arm
adjustment cam to the rear axle
crossmember on both sides.
TIE0024960
Item 12
Exhaust hanger insulator
NOTE: Support the exhaust muffler and tailpipe
assembly.
Item 13
Rear axle crossmember retaining bolts
1. Using
a transmission jack
, support the rear
axle
crossmember.
G401869en
502-00-
44
Uni-Body, Subframe and Mounting System
502-00-
44
REMOVAL AND INSTALLATION
2.
WARNING: Make sure that the rear axle
crossmember is secured to the transmission
jack. Failure to follow this instruction may
result in personal injury.
Using a securing strap, secure the rear axle
crossmember to the transmission jack.
Installation Details
Item 14
Rear axle crossmember
1. Using
a transmission jack, support the
rear
axle
crossmember.
2.
W
ARNING: Make sure that the rear axle
crossmember is secured to the transmission
jack.
Failure to follow this instruction may
result
in personal injury.
Using
a securing strap, secure the rear
axle
crossmember to the transmission jack.
3. Locate the rear axle crossmember.
TIE0001999
Item 13
Rear axle crossmember retaining bolts
1. Install the rear axle crossmember retaining
bolts on both sides.
E56695
125 Nm
2. Remove
the securing strap.
3. Lower
and remove the transmission jack.
Item 11
Rear lower arm
1.
CAUTION: Both sides of the suspension
must be set to the design height setting.
Using two
transmission jacks and
wooden
blocks,
raise the suspension to the
design
height
setting on both sides.
• Position
the transmission jack and
the
wooden block as shown.
TIE0024959
2. NOTE: The spacer must be positioned
exactly as shown.
Install the spacer on both sides.
• Install the spacer between the rear lower arm
and the rear axle crossmember making sure
that the spacer is in a vertical plane.
TIE45679
G401869en
502-00-
45
Uni-Body, Subframe and Mounting System
502-00-
45
REMOVAL AND INSTALLATION
Item 9
Rear lower arm adjustment cam nut
1. NOTE: Do not fully tighten the rear lower arm
adjustment cam nut at this stage.
NOTE: Align the mark on the rear lower arm
adjustment cam to the mark on the rear axle
crossmember.
Install the rear lower arm adjustment cam
nut on both sides.
TIE0036771
8 Nm
Item 4
Stabilizer bar
1. Lower the suspension from the design height
setting on both sides.
1. Remove the spacer.
2. Install the bump stop.
TIE45129
1
2
2. Position the stabilizer bar.
G401869en
Uni-Body, Subframe and Mounting System
REMOVAL AND INSTALLATION
502-00-
46
502-00-
46
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст