Ford Galaxy / Ford S-MAX. Manual — part 707
Warning Devices - Safety Belt Minder
Deactivating/Activating
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
Preparation
Deactivating/Activating
NOTE: Deactivation of the belt minder may also be carried out using IDS. Follow the
instructions on the screen.
1. Apply the parking brake.
2. Place the transmission selector lever in P (Park) -
vehicles with automatic transmission or the
neutral position - vehicles with manual
transmission.
3. Turn the ignition switch to the 0 position.
4. Close all the vehicle doors from the inside of the
vehicle.
1. Unbuckle the drivers safety belt.
2. Turn the ignition switch to position II. (Do not
start the engine).
3. Wait at least 15 seconds.
4.
NOTE: This step must be completed within
60 seconds or the procedure must be
repeated.
Buckle then unbuckle the safety belt nine times,
ending with the safety belt unbuckled. Release
the red unbuckle switch completely every cycle.
5. The safety belt warning indicator flashes three
times to confirm the belt minder status change.
6. Turn the ignition switch to position 0. The
deactivation/activation procedure is now
complete.
Warning Devices - Proximity Warning
Radar Unit Adjustment
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
1. This procedure is required if a new proximity
warning radar unit and, or proximity warning
module are installed or if the proximity warning
radar unit needed to be removed or is misaligned
in its position due to another repair operation.
2. Make sure that the vehicle is on level ground.
3. Activate the adaptive speed control system and
the system will automatically enter service
alignment mode.
4. The FOLLOW indicator on the information and
message center will now be flashing, this
indicates that the vehicle is in service alignment
mode and requires driving.
5. Carry out a road test to set the alignment of the
adaptive speed control system. The following
recommendations will assist in completion of the
alignment process.
6.
The vehicle speed must be above 30 mph
(48 kph).
Choose a road with plenty of road furniture
and use an inside or outside line.
Following vehicles too closely will obscure
the stationary targets from the radar, a
time gap of 2 seconds is recommended.
A straight road will produce a quicker and
better result, although the process will still
operate on a curved road.
The time the adaptive speed control
module takes to align will vary depending
on the route, speed, number of targets and
individual module.
When the flashing FOLLOW indicator light
extinguishes the adaptive speed control
system is now functional and a required
vehicle speed can now be set by the driver.
The speed control system will operate as
normal.
7. In general the procedure can be manually
triggered by the WDS tester systems. If the WDS
is connected and the procedure is selected in the
WDS the procedure will be started and the
telltale will start flashing like described above. An
advantage of this manually triggered procedure
is the presence of a bar on the WDS screen that
is indicating the progress of the adjustment
procedure while driving.
Warning Devices - Oil Change Indicator
Reset
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
1. Close all doors.
2. Turn the ignition key to position II.
3. Simultaneously press the accelerator pedal and
the brake pedal and hold for a minimum of 15
seconds.
4. Press the "OK" button of the multifuctional switch
and the oil change reminder indicator will turn
off. This confirms that the reset procedure has
been correctly completed.
Warning Devices - Proximity Warning
Module
S-MAX/Galaxy 2006.5 (02/2006-)
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details.
Left-hand drive vehicles
Vehicles with air conditioning
Left-hand drive vehicles
Right-hand drive vehicles
1.
2.
3.
4.
5.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст