Ford Galaxy / Ford S-MAX. Manual — part 329
Engine Cooling - 2.0L EcoBoost SCTi
(149kW/203PS) - MI4 - Specifications
S-MAX/Galaxy 2006.5 (02/2006-)
Lubricants, Fluids, Sealers and Adhesives
Antifreeze
Cooling System Refill Capacity
Cooling System Pressure Specification
Item
Specification
Motorcraft Super Plus Antifreeze
WSS-M97B44–D
Specific Gravity (providing no
other additive is in coolant)
Approximate percentage of
Anti-Freeze (by volume)
Remains
Fluid to
Solidifies
at
1.061 at +15°C
50%
–25°C (–13°
F)
–37°C (–
35°F)
Description
Liters
Cooling system and heater
6.2
Description
Pressure kpa (psi)
Radiator pressure test
138 (20)
Coolant expansion tank cap release pressure
135 to 155 (19.6 to 22.5)
Engine Cooling - 2.0L EcoBoost SCTi
(149kW/203PS) - MI4 - Engine Cooling -
Component Location
S-MAX/Galaxy 2006.5 (02/2006-)
Description and Operation
Description
Radiator
Radiator fan motor with bracket
Coolant expansion tank
Wate pump
Thermostat housing
Coolant connection, turbocharger
ECT (engine coolant temperature)
sensor
Coolant distribution connection
Oil cooler
Item
1
2
3
4
5
6
7
8
9
Engine Cooling - 2.0L EcoBoost SCTi
(149kW/203PS) - MI4 - Cooling System
Draining, Filling and Bleeding
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
General Equipment
Draining
WARNING: When releasing the cooling system pressure, cover the coolant expansion
tank cap with a thick cloth.
Fluid container
1. Refer to:
Engine Cooling System Health and
Safety Precautions
(100-00 General Information,
Description and Operation).
2. Release the cooling system pressure by slowly
turning the coolant expansion tank cap between
2 and 3 turns.
3.
4. Refer to:
Lifting
(100-02 Jacking and Lifting,
Description and Operation).
5.
6.
7.
WARNING: Be prepared to collect
escaping fluid.
Filling
CAUTION: The fluid level must remain between the MAX and MIN marks.
Bleeding
Use a suitable coolant hose to drain the coolant.
General Equipment:
Fluid container
Loosen:
3 turn(s)
8.
9. Lower the vehicle.
1. Switch the interior heater blower off.
2. Fill the coolant expansion tank coolant level to
the neck of the coolant expansion tank.
1. Start the engine.
2. Raise the engine speed to 2500 RPM and
maintain it for 1 minute.
3. Check the coolant expansion tank coolant level.
4. If the coolant expansion tank coolant level has
fallen below the MIN mark, stop the engine and
refill the coolant expansion tank level to the neck
of the coolant expansion tank.
5. Install the coolant expansion tank cap.
6. Start the engine if stopped.
7. Raise the engine speed to 2500 RPM and
maintain it for approximately 11 minutes while
observing the coolant expansion tank coolant
level.
8. Maintain the engine speed at 2500 RPM for a
further 3 minutes.
9. Increase the engine speed to 4000 RPM and
maintain it for 5 seconds.
10. Decrease the engine speed to 2500 RPM and
maintain it for 3 minutes.
11. Switch the engine off.
12. Check the cooling system for leaks.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст