Ford Galaxy / Ford S-MAX. Manual — part 967
REPEAT the self-test, CLEAR the
DTCs.
DTC B00DF 01: PAD switch
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
AM.
*
DTC B10FD 11: Driver side
impact sensor short to ground
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
AN.
*
DTC B10FD 12: Driver side
impact sensor short to battery
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
AO.
*
DTC B10FD 19: Driver side
impact sensor cross link to
another firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
AP.
*
DTC B10FD 55: Driver side
impact sensor configuration
failure
RCM.
Driver side impact
sensor.
*
*
Configure the Driver side impact
sensor. REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B10FD 87: Driver side
impact sensor communications
fault
Driver side impact
sensor.
RCM.
Circuit(s).
*
*
*
GO to Pinpoint Test
AQ.
*
DTC B10FD 92: Driver side
impact sensor to restraints
control module (RCM)
mismatch
Incorrect new
driver side impact
sensor installed.
*
INSTALL the correct driver side
impact sensor.
REFER to:
Side Impact Sensor
(501-
20B Supplemental Restraint System,
Removal and Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC B10FD 96: Driver side
impact sensor internal fault
Side impact sensor.
*
INSTALL a new side impact sensor.
REFER to:
Side Impact Sensor
(501-
20B Supplemental Restraint System,
Removal and Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC B10FE 11: Passenger side
impact sensor short to ground
Circuit(s).
*
GO to Pinpoint Test
AR.
*
DTC B10FE 12: Passenger side
impact sensor short to battery
Circuit(s).
*
GO to Pinpoint Test
AS.
*
DTC B10FE 19: Passenger side
impact sensor cross link to
another firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
AT.
*
DTC B10FE 55: Passenger side
impact sensor configuration
failure
RCM.
Passenger side
impact sensor.
*
*
Configure the passenger side impact
sensor. REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B10FE 87: Passenger side
impact sensor communications
fault
Passenger side
impact sensor.
RCM.
Circuit(s).
*
*
*
GO to Pinpoint Test
AU.
*
DTC B10FE 92: Passenger side
impact sensor to restraints
control module (RCM)
mismatch
Incorrect new
passenger side
impact sensor
installed.
*
INSTALL the correct passenger side
impact sensor.
REFER to:
Side Impact Sensor
(501-
20B Supplemental Restraint System,
Removal and Installation).
*
REPEAT the self-test, CLEAR the
DTCs.
DTC B10FE 96: Passenger side
impact sensor internal fault
Side impact sensor.
*
INSTALL a new side impact sensor.
REFER to:
Side Impact Sensor
(501-
20B Supplemental Restraint System,
Removal and Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC B1126 11: Driver side air
bag circuit short to ground
Driver side air bag
module.
Circuit(s).
*
*
GO to Pinpoint Test
AV.
*
DTC B1126 12: Driver side air
bag circuit short to battery
Driver side air bag
module.
Circuit(s).
*
*
GO to Pinpoint Test
AW.
*
DTC B1126 13: Driver side air
bag circuit open circuit or high
resistance
Driver side air bag
module.
Circuit(s).
*
*
GO to Pinpoint Test
AX.
*
DTC B1126 19: Driver side air
bag cross link to another firing
circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
AY.
*
DTC B1126 1A: Driver side air
bag circuit low resistance
Driver side air bag
module.
Circuit(s).
*
*
GO to Pinpoint Test
AZ.
*
DTC B1126 55: Driver side air
bag configuration failure
RCM.
Driver side air bag.
*
*
Configure the driver side air bag.
REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B1127 11: Passenger side
air bag circuit short to ground
Passenger side air
bag module.
Circuit(s).
*
*
GO to Pinpoint Test
BA.
*
DTC B1127 12: Passenger side
air bag circuit short to battery
Passenger side air
bag module.
Circuit(s).
*
*
GO to Pinpoint Test
BB.
*
DTC B1127 13: Passenger side
air bag circuit open circuit or
high resistance
Passenger side air
bag module.
Circuit(s).
*
*
GO to Pinpoint Test
BC.
*
DTC B1127 19: Passenger side
air bag cross link to another
firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
BD.
*
DTC B1127 1A: Passenger side
air bag circuit low resistance
Passenger side air
bag module.
Circuit(s).
*
*
GO to Pinpoint Test
BE.
*
DTC B1127 55: Passenger side
air bag configuration failure
RCM.
Passenger side air
bag.
*
*
Configure the passenger side air bag.
REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B1128 11: Driver side air
curtain circuit short to ground
Driver side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BF.
*
DTC B1128 12: Driver side air
curtain circuit short to battery
Circuit(s).
*
GO to Pinpoint Test
BG.
*
DTC B1128 13: Driver side air
curtain circuit open circuit or
high resistance
Driver side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BH.
*
DTC B1128 19: Driver side air
curtain cross link to another
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
firing circuit
before carrying out the pinpoint test.
GO to Pinpoint Test
BI.
*
DTC B1128 1A: Driver side air
curtain circuit low resistance
Driver side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BJ.
*
DTC B1128 55: Driver side air
curtain configuration failure
RCM.
Driver side air
curtain.
*
*
Configure the driver side air curtain.
REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B1129 11: Passenger side
air curtain circuit short to
ground
Passenger side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BK.
*
DTC B1129 12: Passenger side
air curtain circuit short to
battery
Circuit(s).
*
GO to Pinpoint Test
BL.
*
DTC B1129 13: Passenger side
air curtain circuit open circuit
or high resistance
Passenger side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BM.
*
DTC B1129 19: Passenger side
air curtain cross link to
another firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
BN.
*
DTC B1129 1A: Passenger side
air curtain circuit low
resistance
Passenger side air
curtain module.
Circuit(s).
*
*
GO to Pinpoint Test
BO.
*
DTC B1129 55: Passenger side
air curtain configuration failure
RCM.
Passenger side air
curtain.
*
*
Configure the passenger side air
curtain. REFER to the Ford approved
diagnostic tool. REPEAT the self-test,
CLEAR the DTCs.
*
DTC B1A55 12: Event
notification signal circuit short
to ground or open circuit
Circuit.
*
GO to Pinpoint Test
BP.
*
DTC B1A55 14: Event
notification signal circuit short
to battery
Circuit.
*
GO to Pinpoint Test
BQ.
*
DTC B1B69 16: Battery
voltage low
Battery.
Charging system.
Circuit.
*
*
*
GO to Pinpoint Test
BR.
*
DTC B1B69 17: Battery
voltage high
Charging system.
*
Check the charging system.
REFER to:
Charging System
(414-00
Charging System - General
Information, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC B1D74 12: PAD switch
short to battery
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BS.
*
DTC B1D74 13: PAD switch
open circuit or high resistance
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BT.
*
DTC B1D74 19: PAD switch
circuit cross link to another
firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
BU.
*
DTC B1D74 1A: PAD switch
short circuit
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BV.
*
DTC B1D74 1E: PAD switch
resistance out of range
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BW.
*
DTC B1D74 55: PAD switch
configuration failure
RCM.
PAD switch.
*
*
Configure the PAD switch. REFER to
the Ford approved diagnostic tool.
*
Pinpoint Tests
REPEAT the self-test, CLEAR the
DTCs.
DTC B1D75 12: PAD switch
short to battery
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BX.
*
DTC B1D75 13: PAD switch
open circuit or high resistance
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
BY.
*
DTC B1D75 19: PAD switch
circuit cross link to another
firing circuit
Circuit(s).
*
NOTE: Check for a matching ‘cross
link to another firing circuit’ DTC
before carrying out the pinpoint test.
GO to Pinpoint Test
BZ.
*
DTC B1D75 1A: PAD switch
short circuit
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
CA.
*
DTC B1D75 1E: PAD switch
resistance out of range
PAD switch.
Circuit(s).
*
*
GO to Pinpoint Test
CB.
*
DTC B1D75 55: PAD switch
configuration failure
RCM.
PAD switch.
*
*
Configure the PAD switch. REFER to
the Ford approved diagnostic tool.
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0010 88 Control module
communications bus off
Circuit(s).
*
GO to Pinpoint Test
CC.
*
DTC U0140 00: Lost
communication with Generic
electronic module (GEM).
CAN bus.
*
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
*
DTC U0155 00: Lost
communication with
instrument cluster
CAN bus.
*
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
*
DTC U1A37 00: Crash status
telegram
RCM crash data.
*
Clear the data memory using the Ford
diagnostic equipment. REPEAT the self
test, CLEAR the DTCs.
*
DTC U2100 00: Restraints
control module (RCM)
configuration failure
New RCM
incorrectly
configured.
*
CHECK model option content.
CONFIGURE the RCM. For additional
information, REFER to the Ford
approved diagnostic tool.
*
DTC U2101 00: Restraints
control module (RCM)
configuration incompatible
New RCM
incorrectly
configured.
*
CHECK model option content.
CONFIGURE the RCM. For additional
information, REFER to the Ford
approved diagnostic tool.
*
DTC U3000 00: Restraints
control module (RCM) is
defective
RCM.
*
INSTALL a new RCM.
REFER to:
Restraints Control Module
(RCM)
(501-20B Supplemental
Restraint System, Removal and
Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U3000 13: Air bag
diagnostic monitor ground
circuit open
RCM.
*
GO to Pinpoint Test
CD.
*
PINPOINT TEST A : NO COMMUNICATION WITH THE MODULE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
A1: CHECK THE FORD APPROVED DIAGNOSTIC TOOL IS COMMUNICATING THROUGH
THE DATA LINK CONNECTOR (DLC)
WARNING: To avoid accidental deployment, the RCM backup power supply must be
depleted. Wait at least one minute after disconnecting the battery ground cable(s) before
commencing any repair or adjustment to the SRS, or any component(s) adjacent to the
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст