Ford Galaxy / Ford S-MAX. Manual — part 799
REPAIR the circuit. TEST the system for normal
operation.
PINPOINT TEST F : THE FRONT FOOTWELL LAMP(S) ARE INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
F1: CHECK OPERATION OF THE FOOTWELL LAMPS
Check for operation of the front footwell lamp(s).
1
Are both the front footwell lamp(s) inoperative?
Yes
GO to F3
.
No
If the right-hand side front footwell lamp is
inoperative.
GO to F5
.
If the left-hand side front footwell lamp is
inoperative.
GO to F2
.
F2: CHECK CIRCUIT CBP17H (BN/WH) FOR VOLTAGE
Disconnect Left-hand Front Footwell Lamp C3LN38.
1
Measure the voltage between the left-hand front
footwell lamp C3LN38 pin 1, circuit CBP17H (BN/GN),
harness side and ground.
2
Is the voltage greater than 10 volts?
Yes
GO to F4
.
No
GO to F3
.
F3: CHECK THE LEFT-HAND FRONT FOOTWELL LAMP POWER CIRCUIT FOR OPEN
CIRCUIT
Disconnect CJB C1BP02-C.
1
Measure the resistance between the left-hand front
footwell lamp C3LN38 pin 1, circuit CBP17H (BN/GN),
harness side and the CJB C1BP02-C pin 67, circuit
CBP17R (BN/GN), harness side.
2
Is the resistance less than 1 ohm?
Yes
GO to Pinpoint Test
H.
No
REPAIR circuit CBP17H (BN/GN) or circuit CBP17R
(BN/GN) as necessary. TEST the system for normal
operation. If the concern persists, INSTALL a new
left-hand front footwell lamp. TEST the system for
normal operation.
F4: CHECK CIRCUIT CLN38A (BU/GY) FOR OPEN CIRCUIT
Disconnect CJB C1BP02-B.
1
Measure the resistance between the left-hand front
footwell lamp C3LN38 pin 2, circuit CLN38A (BU/GY),
2
harness side and the CJB C1BP02_B pin 37, circuit
CLN38A (BU/GY), harness side.
Is the resistance less than 1 ohm?
Yes
REFER to the WDS.
No
REPAIR the circuit. TEST the system for normal
operation. If the concern persists, INSTALL a new
left-hand front footwell lamp. TEST the system for
normal operation.
F5: CHECK CIRCUIT CBP17L (BN/GN) FOR VOLTAGE
Disconnect Right-hand Front Footwell Lamp C3LN39.
1
Measure the voltage between the right-hand front
footwell lamp C3LN39 pin 1, circuit CBP17L (BN/GN),
harness side and ground.
2
Is the voltage greater than 10 volts?
Yes
GO to F7
.
No
GO to F6
.
F6: CHECK THE RIGHT-HAND FRONT FOOTWELL LAMP POWER CIRCUIT FOR OPEN
CIRCUIT
Disconnect CJB C1BP02-C.
1
Measure the resistance between the right-hand front
footwell lamp C3LN39 pin 1, circuit CBP17L (BN/GN),
harness side and the CJB C1BP02-C pin 67, circuit
CBP17R (BN/GN), harness side.
2
Is the resistance less than 1 ohm?
Yes
REFER to the WDS.
No
REPAIR circuit CBP17L (BN/GN) or circuit CBP17R
(BN/GN) as necessary. TEST the system for normal
operation. If the concern persists, INSTALL a new
right-hand front footwell lamp. TEST the system for
normal operation.
F7: CHECK CIRCUIT CLN38C (BU/WH) FOR OPEN CIRCUIT
Disconnect CJB C1BP02-C.
1
Measure the resistance between the right-hand front
footwell lamp C3LN39 pin 2, circuit CLN38C
(BU/WH), harness side and the CJB C1BP02-C pin 19,
circuit CLN38C (BU/WH), harness side.
2
Is the resistance less than 1 ohm?
Yes
REFER to the WDS.
No
REPAIR the circuit. TEST the system for normal
operation. If the concern persists, INSTALL a new
right-hand front footwell lamp. TEST the system for
normal operation.
PINPOINT TEST G : THE VANITY MIRROR LAMP(S) ARE INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
G1: CHECK OPERATION OF THE VANITY MIRROR LAMP
Check for operation of the vanity mirror lamp(s).
1
Are both the vanity mirror lamp(s) inoperative?
Yes
GO to G6
.
No
If the driver side vanity mirror lamp is inoperative.
GO to G2
.
If the passenger side vanity mirror lamp is
inoperative.
GO to G5
.
G2: CHECK CIRCUIT CBP17D (BN/GN) FOR VOLTAGE
Disconnect Driver Side Vanity Mirror Lamp C5LN23.
1
Measure the voltage between the driver side vanity
mirror lamp C5LN23 pin 1, circuit CBP17D (BN/GN),
harness side and ground.
2
Is the voltage greater than 10 volts?
Yes
GO to G4
.
No
GO to G3
.
G3: CHECK THE DRIVER SIDE VANITY MIRROR LAMP POWER CIRCUIT FOR OPEN
CIRCUIT
Disconnect CJB C1BP02-C.
1
Measure the resistance between the driver side
vanity mirror lamp C5LN23 pin 1, circuit CBP17D
(BN/GN), harness side and the CJB C1BP02-C pin 67,
circuit CBP17R (BN/GN), harness side.
2
Is the resistance less than 1 ohm?
Yes
GO to Pinpoint Test
H.
No
REPAIR circuit CBP17D (BN/GN) or circuit CBP17R
(BN/GN) as necessary. TEST the system for normal
operation. If the concern persists, INSTALL a new
driver side vanity mirror lamp. TEST the system for
normal operation.
G4: CHECK CIRCUIT GD138AF (BK/WH) FOR GROUND
Measure the resistance between the driver side
vanity mirror lamp C5LN23 pin 3, circuit GD138AF
(BK/WH), harness side and ground.
1
Is the resistance less than 1 ohm?
Yes
INSTALL a new driver side vanity mirror lamp. TEST
the system for normal operation
No
REPAIR the circuit. TEST the system for normal
operation.
G5: CHECK CIRCUIT CBP17F (BN/GN) FOR VOLTAGE
Disconnect Passenger Side Vanity Mirror Lamp
C6LN24.
1
Measure the voltage between the passenger side
vanity mirror lamp C6LN24 pin 1, circuit CBP17F
(BN/GN), harness side and ground.
2
Is the voltage greater than 10 volts?
Yes
GO to G7
.
No
GO to G6
.
G6: CHECK THE PASSENGER SIDE VANITY MIRROR LAMP POWER CIRCUIT FOR OPEN
CIRCUIT
Disconnect CJB C1BP02-C.
1
Measure the resistance between the passenger side
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст