Ford Galaxy / Ford S-MAX. Manual — part 697
Instrument Cluster and Panel Illumination
- Instrument Cluster and Panel
Illumination
S-MAX/Galaxy 2006.5 (02/2006-)
Diagnosis and Testing
Refer to Wiring Diagrams Section 413-00, for schematic and connector
information.
General Equipment
Instrument Cluster and Dimmable Backlighting
The dimmable illumination utilizes light emitting diodes (LEDs) and bulb(s).
The following dimmable components are backlit using LEDs only:
transmission control lever
heater control panel
audio unit
navigation system display module
instrument cluster
climate control module
hazard switch
traction control system disable switch
right-hand and left-hand heated front seat switch(es)
Inspection and Verification
1. 1. Verify the customer concern.
2. 2. Visually inspect for obvious signs of mechanical or electrical damage.
Visual Inspection Chart
3. 3. If an obvious cause for an observed or reported concern is found, correct the cause
(if possible) before proceeding to the next step
4. 4. If the cause is not visually evident, verify the symptom and refer to the Symptom
Chart.
Symptom Chart
Worldwide diagnostic system (WDS)
Mechanical
Electrical
Engine/engine compartment or underbody
components
Fluid levels
Accessory installation
Fuse(s)
Loose or corroded connector
(s)
Instrument cluster
Switch(es)
Wiring Harness
Circuit(s)
LED(s)
Symptom
Possible Sources
Action
The control illumination is inoperative
Fuse.
Headlamp switch.
Circuit.
*
*
*
REFER to the WDS.
*
The instrument panel illumination does not
dim
Dimmer switch.
*
INSTALL a new
headlamp/dimmer switch
*
Pinpoint Tests
NOTE: Use a digital multimeter for all electrical measurements.
unit.
The Instrument cluster illumination is
inoperative
Circuit(s).
Instrument
cluster.
*
*
REFER to the WDS.
*
The climate control illumination is inoperative
Circuit(s).
Climate control
assembly.
*
*
REFER to the WDS.
*
The audio system illumination is inoperative
Circuit(s).
Audio unit.
*
*
REFER to the WDS.
*
The navigation system display module
illumination (vehicles with Travel Pilot EX) is
inoperative
Circuit(s).
Navigation
system display
module.
*
*
REFER to the WDS.
*
The navigation system display module
illumination (vehicles with DVD Navigation
System with Touchscreen) is inoperative
Circuit(s).
Navigation
system display
module.
*
*
REFER to the WDS.
*
The cigar lighter illumination is inoperative
Circuit(s).
Cigar lighter.
*
*
GO to Pinpoint Test
A.
*
The hazard switch illumination is inoperative
Circuit(s).
Hazard switch.
*
*
GO to Pinpoint Test
B.
*
The front seat heater switch(es) illumination
is inoperative
Circuit(s).
Front seat heater
switch(es).
*
*
GO to Pinpoint Test
C.
*
The front and rear window defrost switch
illumination is inoperative
Circuit(s).
Rear window
defrost switch.
*
*
GO to Pinpoint Test
D.
*
The parking aid switch illumination is
inoperative
Circuit(s).
parking aid
switch.
*
*
GO to Pinpoint Test
E.
*
The electronic parking brake switch
illumination is inoperative
Circuit(s).
Electronic parking
brake switch.
*
*
GO to Pinpoint Test
F.
*
PINPOINT TEST A : THE CIGAR LIGHTER ILLUMINATION IS INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
A1: CHECK CIRCUIT CLN17S (BN) FOR VOLTAGE
Disconnect Cigar Lighter C2DC07-B.
1
Ignition switch in position II.
2
Make sure that the illumination dimmer switch is in
the full illumination position.
3
Place the headlamp switch in the ON position.
4
Measure the voltage between the cigar lighter
C2DC07-B pin 1, circuit CLN17S (BN), harness side
and ground.
5
Is the voltage greater than 10 volts?
Yes
GO to A2
.
No
REPAIR the circuit CLN17S (BN) or circuit CLN17G
(BN) as necessary. TEST the system for normal
operation.
A2: CHECK CIRCUIT GD138AZ (BK/WH) FOR OPEN
Connect Cigar Lighter C2DC07-B.
1
Disconnect Cigar Lighter C2DC07-A.
2
Measure the resistance between the cigar lighter
C2DC07-A pin 1, circuit GD138AZ (BK/WH), harness
side and ground.
3
Is the resistance less than 5 ohms?
Yes
INSTALL a new cigar lighter. TEST the system for
normal operation.
No
REPAIR circuit GD138AZ (BK/WH) or circuit GD138AL
(BN/WH) as necessary. TEST the system for normal
operation.
PINPOINT TEST B : THE HAZARD SWITCH ILLUMINATION IS
INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
B1: CHECK CIRCUIT CLS38A (VT/WH) FOR VOLTAGE
Disconnect Hazard Switch C2LS32.
1
Ignition switch in position II.
2
Make sure that the illumination dimmer switch is in
the full illumination position.
3
Place the headlamp switch in the ON position.
4
Measure the voltage between the hazard switch
C2LS32 pin 5, circuit CLS38A (VT/WH), harness side
and ground.
5
Is the voltage greater than 10 volts?
Yes
GO to B2
.
No
REPAIR the circuit. TEST the system for normal
operation.
B2: CHECK CIRCUIT GD133CF (BK) FOR OPEN
Ignition switch in position 0.
1
Measure the resistance between hazard switch
C2LS32 pin 4, circuit GD133CF (BK), harness side
and ground.
2
Is the resistance less than 5 ohms?
Yes
INSTALL a new hazard switch. TEST the system for
normal operation.
No
REPAIR the circuit GD133CF (BK) or circuit GD133AW
(BK) as necessary. TEST the system for normal
operation.
PINPOINT TEST C : THE FRONT SEAT HEATER SWITCH ILLUMINATION IS
INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
C1: CHECK INOPERATIVE FRONT SEAT HEATER SWITCH FOR VOLTAGE
Disconnect Front Seat Heater Switch - C3HS29.
1
Ignition switch in position II.
2
Make sure that the illumination dimmer switch is in
the full illumination position.
3
Place the headlamp switch in the ON position.
4
Measure the voltage between the front seat heater
switch C3HS29 pin 3, circuit CLN17H (BN), harness
side and ground.
5
Is the voltage greater than 10 volts?
Yes
GO to C2
.
No
REPAIR circuit CLN17H (BN), circuit CLN17J (BN) or
circuit CLN17G (BN) as necessary. TEST the system
for normal operation.
C2: CHECK THE FRONT SEAT HEATER SWITCH FOR OPEN
Measure the resistance between the front seat
heater switch C3HS29 pin 1, circuit GD138AP (BK),
harness side and ground.
1
Is the resistance less than 5 ohms?
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст