Ford Galaxy / Ford S-MAX. Manual — part 901
Disconnect Driver Side Exterior Mirror C5PM26-A.
2
Ignition switch in position II.
3
Select the driver side exterior mirror. While
operating the exterior mirror switch UP and DOWN,
measure the voltage between the driver side exterior
mirror C5PM26-A pin 2, circuit CPM03A (BU/WH),
harness side and the driver side exterior mirror
C5PM26-A pin 3, circuit CPM28A (BU/BN), harness
side.
4
Is the voltage greater than 10 volts when the exterior
mirror switch is moved to the UP position and is the
polarity reversed when moved to the DOWN position?
Yes
INSTALL a new driver side exterior mirror.
REFER to: Exterior Mirror (501-09 Rear View Mirrors,
Removal and Installation).
TEST the system for normal operation.
No
GO to B3
.
B3: CHECK THE DRIVER SIDE EXTERIOR MIRROR UP/DOWN CIRCUIT FOR
CONTINUITY
Ignition switch in position 0.
1
Disconnect Driver Door Module C5PL01-B.
2
Measure the resistance between the driver door
module C5PL01-B pin 24, circuit CPM29A (GN),
harness side and the driver side exterior mirror
C5PM26-A pin 3, circuit CPM28A (BU/BN), harness
side.
3
Is the resistance less than 5 ohms?
Yes
VERIFY the customer concern. TEST the system for
normal operation.
No
REPAIR circuit CPM28A (BU/BN). TEST the system for
normal operation.
B4: CHECK THE DRIVER SIDE EXTERIOR MIRROR LEFT/RIGHT CIRCUIT
Ignition switch in position 0.
1
Disconnect Driver Side Exterior Mirror C5PM26-A.
2
Ignition switch in position II.
3
Select the driver side exterior mirror. While
operating the exterior mirror switch LEFT and RIGHT,
measure the voltage between the driver side exterior
mirror C5PM26-A pin 1, circuit CPM29A (GN), harness
side and the driver side exterior mirror C5PM26-A pin
2, circuit CPM29A (GN), harness side.
4
Is the voltage greater than 10 volts when the exterior
mirror switch is moved to the LEFT position and is the
polarity reversed when moved to the RIGHT position?
Yes
INSTALL a new driver side exterior mirror.
REFER to: Exterior Mirror (501-09 Rear View Mirrors,
Removal and Installation).
TEST the system for normal operation.
No
GO to B5
.
B5: CHECK THE DRIVER SIDE EXTERIOR MIRROR LEFT/RIGHT CIRCUIT FOR
CONTINUITY
Ignition switch in position 0.
1
Disconnect Driver Door Module C5PL01-B.
2
Measure the resistance between the driver door
module C5PL01-B pin 8, circuit CPM29A (GN),
harness side and the driver side exterior mirror
C5PM26-A pin 1, circuit CPM29A (GN), harness side.
3
Is the resistance less than 5 ohms?
Yes
VERIFY the customer concern. TEST the system for
normal operation.
No
REPAIR circuit CPM29A (GN). TEST the system for
normal operation.
B6: CHECK THE PASSENGER SIDE MIRROR UP/DOWN CIRCUIT
Ignition switch in position 0.
1
Disconnect Passenger Side Exterior Mirror C5PM31-A.
2
Ignition switch in position II.
3
Select the passenger side exterior mirror. While
operating the exterior mirror switch UP and DOWN,
measure the voltage between the passenger side
exterior mirror C5PM31-A pin 2, circuit CPM06A
(GN/WH), harness side and the passenger side
exterior mirror C5PM31-A pin 3, circuit CPM33A
(VT/BK), harness side.
4
Is the voltage greater than 10 volts when the exterior
mirror switch is moved to the UP position and is the
polarity reversed when moved to the DOWN position?
Yes
INSTALL a new passenger side exterior mirror.
REFER to: Exterior Mirror (501-09 Rear View Mirrors,
Removal and Installation).
TEST the system for normal operation.
No
GO to B7
.
B7: CHECK THE PASSENGER SIDE MIRROR UP/DOWN CIRCUIT FOR CONTINUITY
Ignition switch in position 0.
1
Disconnect Passenger Door Module C6PL01-B.
2
Measure the resistance between the passenger door
3
module C6PL01-B pin 24, circuit CPM33A (VT/BK),
harness side and the passenger side exterior mirror
C5PM31-A pin 3, circuit CPM33A (VT/BK), harness
side.
Is the resistance less than 5 ohms?
Yes
VERIFY the customer concern. TEST the system for
normal operation.
No
REPAIR circuit CPM33A (VT/BK). TEST the system for
normal operation.
B8: CHECK THE PASSENGER SIDE EXTERIOR MIRROR LEFT/RIGHT CIRCUIT
Ignition switch in position 0.
1
Disconnect Passenger Side Exterior Mirror C5PM31-A.
2
Ignition switch in position II.
3
Select the passenger side exterior mirror. While
operating the exterior mirror switch LEFT and RIGHT,
measure the voltage between the passenger side
exterior mirror C5PM31-A pin 1, circuit CPM34A
(WH/BN), harness side and the passenger side
exterior mirror C5PM31-A pin 2, circuit CPM06A
(GN/WH), harness side.
4
Is the voltage greater than 10 volts when the exterior
mirror switch is moved to the LEFT position and is the
polarity reversed when moved to the RIGHT position.
Yes
INSTALL a new passenger side exterior mirror.
REFER to: Exterior Mirror (501-09 Rear View Mirrors,
Removal and Installation).
TEST the system for normal operation.
No
GO to B9
.
B9: CHECK THE PASSENGER SIDE EXTERIOR MIRROR LEFT/RIGHT CIRCUIT FOR
CONTINUITY
Ignition switch in position 0.
1
Disconnect Passenger Door Module C6PL01-B.
2
Measure the resistance between the passenger door
module C6PL01-B pin 8, circuit CPM34A (WH/BN),
harness side and the passenger side exterior mirror
C5PM31-A pin 1, circuit CPM34A (WH/BN), harness
side.
3
Is the resistance less than 5 ohms?
Yes
VERIFY the customer concern. TEST the system for
normal operation.
No
REPAIR circuit CPM34A (WH/BN). TEST the system
for normal operation.
PINPOINT TEST C : THE HEATED EXTERIOR MIRROR IS INOPERATIVE
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
C1: CHECK THE OPERATION OF THE HEATED REAR WINDOW
NOTE: Use a digital multimeter for all electrical measurements.
Ignition switch in position III.
1
Ignition switch in position II.
2
Operate the heated rear window switch.
3
Does the heated rear window function correctly?
Yes
GO to C2
.
No
REPAIR the heated rear window.
REFER to: Glass, Frames and Mechanisms (501-11
Glass, Frames and Mechanisms, Diagnosis and
Testing).
TEST the system for normal operation.
C2: CHECK THE VOLTAGE TO THE INOPERATIVE EXTERIOR MIRROR
Ignition switch in position 0.
1
Disconnect Inoperative Exterior Mirror C5PM26-A or
C5PM31-A.
2
Ignition switch in position III.
3
Ignition switch in position II.
4
Operate the heated rear window switch.
5
Measure the voltage between the:
Driver side exterior mirror C5PM26-A pin 5, circuit
CRD13A (GN/VT), harness side and ground.
Passenger side exterior mirror C5PM31-A pin 5,
circuit CRD14A (WH/OG), harness side and ground.
6
Is the voltage greater than 10 volts?
Yes
GO to C3
.
No
REPAIR circuit CRD13A (GN/VT) or circuit CRD14A
(WH/OG). TEST the system for normal operation.
C3: CHECK THE INOPERATIVE EXTERIOR MIRROR GROUND CIRCUIT FOR
CONTINUITY
Ignition switch in position 0.
1
Disconnect Inoperative Mirror Door Module C5PL01-B
or C6PL01-B.
2
Measure the resistance between the:
Driver side exterior mirror C5PM26-A pin 5, circuit
CRD13A (GN/VT), harness side and the driver side
door module C5PL01-B pin 10, circuit CRD13A
(GN/VT).
Passenger side exterior mirror C5PM31-A pin 5,
circuit CRD14A (WH/OG), harness side and the
passenger side door module C6PL01-B pin 10,
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст