Ford Freestyle (2007 year). Manual — part 18
STEERING WHEEL CONTROLS (IF EQUIPPED)
Radio control features
• Press MEDIA to select AM, FM1,
FM2, TAPE or CD (if equipped).
In Radio mode:
• Press SEEK to access the
next/previous strong station.
In Tape mode:
• Press SEEK to listen to the
next/previous selection on the
tape.
In CD mode:
• Press SEEK to listen to the next/previous track on the disc.
In any mode:
• Press VOL up or down to adjust
the volume.
• Press MUTE to mute the volume.
HOMELINK
姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)
The HomeLink
威 Wireless Control
System, located on the driver’s visor,
provides a convenient way to
replace up to three hand-held
transmitters with a single built-in
device. This feature will learn the
radio frequency codes of most
transmitters to operate garage
doors, entry gate operators, security systems, entry door locks, and
home or office lighting.
Driver Controls
74
When programming your HomeLink
威 Wireless Control System to
a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLink
威 Wireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink
威 at: www.homelink.com or 1–800–355–3515.
Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink
威 equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink
威 buttons be erased for security purposes, refer to
Programming in this section.
Programming
Do not program HomeLink
威 with the vehicle parked in the garage.
Note: Your vehicle may require the ignition switch to be turned to the
ACC position for programming and/or operation of the HomeLink
威. It is
also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLink
威 for quicker
training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the
indicator light begins to flash after
20 seconds. Do not repeat Step 1
to program additional hand-held
transmitters to the remaining two
HomeLink
威 buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink
威.
2. Position the end of your
hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink
威
button you wish to program (located on your visor) while keeping the
indicator light in view.
Driver Controls
75
3. Simultaneously press and hold
both the HomeLink
威 and hand-held
transmitter button. Do not release
the buttons until Step 4 has
been completed.
Some entry gates and garage door
openers may require you to replace
Step 3 with procedures noted in the
“Gate Operator and Canadian Programming” in this section for Canadian
residents.
4. The indicator light will flash slowly and then rapidly. Release both
buttons when the indicator light flashes rapidly. (The rapid flashing light
indicates acceptance of the hand-held transmitters’ radio frequency
signals.)
5. Press and hold the just-trained HomeLink
威 button and observe the
indicator light. If the light is constant, programming is complete and your
device should activate when the HomeLink
威 button is pressed and
released. Note: To program the remaining two HomeLink
威 buttons,
begin with Step 2 in the “Programming” section — do not repeat Step 1.
Note: If the indicator light blinks rapidly for two seconds and then turns
to a continuous red, proceed with Steps 6 through 8 to complete
programming of a rolling code equipped device.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).
7. Press and release the “learn” or “smart” button. (The name and color
of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate Step 8.
8. Return to the vehicle and firmly press, hold for two seconds and
release the HomeLink
威 button. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.
HomeLink
威 should now activate your rolling code equipped device. To
program additional HomeLink
威 buttons begin with Step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1–800–355–3515.
Driver Controls
76
Gate Operator & Canadian Programming
During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLink
威 to accept the signal
from the hand-held transmitter.
After completing Steps 1 and 2
outlined in the “Programming”
section, replace Step 3 with the following:
Note: If programming a garage door opener or gate operator, it is
advised to unplug the device during the “cycling” process to prevent
overheating.
• Continue to press and hold the HomeLink威 button (note Step 3 in the
“Programming” section) while you press and release — every two
seconds (“cycle”) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink
威. The indicator light will
flash slowly and then rapidly after HomeLink
威 accepts the radio
frequency signal.
• Proceed with Step 4 in the “Programming” section.
Operating the HomeLink
姞 Wireless Control System
To operate, simply press and release
the appropriate HomeLink
威 button.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the event that there are still
programming difficulties, contact HomeLink
威 at www.homelink.com or
1–800–355–3515.
Driver Controls
77
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст