Ford Freestyle (2007 year). Manual — part 22

Note: Continued force applied after unlatching may activate the obstacle
detection feature and stop the power system. For the best performance
allow the power system to open the PLG after releasing the handle.

To power close the PLG from the
liftgate trim switch:

1. Ensure the Power Door Lockout
Control is in the ON position.

2. Press and release the control on
the bottom of the liftgate trim panel
to engage the power assist feature.
If a single chime is heard, check to
be sure that the Power Door
Lockout Switch is set to ON and
that the transaxle is in Park.

To operate the PLG manually:

1. Disable the liftgate power function by placing the Power Door Lockout
Control in the OFF position.

2. Open and close the liftgate as you would a standard liftgate.

Note: In case of operation in extreme cold -40° F (-40° C), or on
extreme inclines, manual operation of the liftgate is suggested.

Safety/Obstructions

If anything obstructs the PLG while it is power opening or closing, the
PLG will automatically reverse or stop depending on the position of the
liftgate, provided it meets sufficient resistance. If the PLG encounters an
obstacle while closing, the PLG will reverse to full open. Once the
obstacle is removed, the PLG can be again closed under power. If the
PLG encounters an obstacle while opening, the PLG will stop when it
encounters a solid obstacle. Close the liftgate manually and remove the
obstruction. Normal operation can then be resumed.

Resetting the PLG:

The power liftgate may not operate properly if any of the following
conditions occur:
• a low voltage or dead battery
• disconnected battery
• the liftgate has been left open or unlatched for more than six (6)

hours

Driver Controls

90

If any of these conditions occur, the PLG must be reset. To reset the
PLG:

1. Manually close and fully latch the liftgate.

2. Power open the liftgate by using the remote entry transmitter or
overhead console button.

3. Once the liftgate is fully open, close the liftgate using the power
switch on the liftgate, remote entry transmitter or overhead console
button.

Liftgate ajar signal

If the liftgate is not fully latched, you will receive a “LIFTGATE AJAR”
message on the instrument panel. If you see this message, check the
liftgate to ensure it is fully latched.

Make sure the liftgate is closed to prevent exhaust fumes from
being drawn into the vehicle. If you must drive with the liftgate

open, keep the climate control vents open so that fresh outside air
circulates through the vehicle.

CARGO AREA FEATURES

Cargo net (if equipped)

The cargo pouch net secures
lightweight objects in the cargo
area. Attach the net to the anchors
provided. Do not put more than
50 lbs. (22 kg) in the net.

The cargo net is not
designed to restrain objects

during a collision or heavy
braking.

Driver Controls

91

Utility hooks

The utility hooks can be used to
hang small items. Do not hang more
than 20 lb. (12 kg) on each of the
hooks. The hooks are not designed
to restrain objects during a collision.

LUGGAGE RACK (IF EQUIPPED)

Maximum load is 125 lbs (57 kg) on
the roof rack structure, or 100 lbs
(45 kg) on the roof panel, evenly
distributed. If it is not possible to
distribute the load, position it as far
rearward as possible.

To adjust the cross-bar (if equipped) position:

1. Loosen the thumbwheel at both
ends of the cross-bar (both
cross-bars are adjustable).

2. Slide the cross-bar to the desired
location.

3. Tighten the thumbwheel at both
ends of the cross-bar.

Driver Controls

92

To remove the cross-bar assembly (if equipped):

1. Remove rear support covers from
the rear rails. Place a small object
into the pin holes and slide the
cover out towards the rear of the
vehicle.

2. Loosen the thumbwheel at both
ends of the cross-bar and slide the
cross-bar towards the rear of the
vehicle.

3. De-press the metal retention clip
located in the inner rail channel on
both sides, and slide the crossbar
out simultaneously.

Driver Controls

93