Ford E-350 (2010 year). Manual — part 40

Performing the TPMS reset procedure (Vehicles that have wheels
with snap-in pressure sensors)

It is recommended that you read the entire procedure before attempting.

1. Drive the vehicle above 20 mph (32 km/h) for at least two minutes
and then park in a safe location where you can easily get to all four tires
and have access to an air pump.

2. Place the ignition in the off position and keep the key in the ignition.

3. Cycle the ignition to the on
position with the engine off.

4. Turn the hazard flashers on then
off three times. This must be
accomplished within 10 seconds.

If the reset mode has been entered successfully, the horn will sound
once, the TPMS indicator

will flash and the message center (if

equipped) will display TRAIN LEFT FRONT TIRE. If this does not
occur, please try again starting at Step 2.

If after repeated attempts to enter the reset mode, the horn does not
sound, the TPMS indicator

does not flash and the message center (if

equipped) does not display TRAIN LEFT FRONT TIRE, seek service
from your authorized dealer.

Tires, Wheels and Loading

161

5. Train the TPMS sensors in the tires using the following TPMS reset
sequence starting with the left front tire in the following clockwise
order:
• Left front (Driver’s side front tire)
• Right front (Passenger’s side front tire)
• Right rear (Passenger’s side rear tire)
• Left rear (Driver’s side rear tire)
6. Remove the valve cap from the valve stem on the left front tire.
Decrease the air pressure until the horn sounds.

Note: The single horn chirp confirms that the sensor identification code
has been learned by the module for this position. If a double horn is
heard, the reset procedure was unsuccessful, and must be repeated.

7. Remove the valve cap from the valve stem on the right front tire.
Decrease the air pressure until the horn sounds.

8. Remove the valve cap from the valve stem on the right rear tire.
Decrease the air pressure until the horn sounds.

9. Remove the valve cap from the valve stem on the left rear tire.
Decrease the air pressure until the horn sounds.

Training is complete after the horn sounds for the last tire trained
(driver’s side rear tire), the TPMS tell tale stops flashing, and the
message center (if equipped) displays:
TRAINING COMPLETE.

10. Turn the ignition off. If two short horn beeps are heard, the reset
procedure was unsuccessful and must be repeated.

If after repeating the procedure and two short beeps are heard when the
ignition is turned to off, seek assistance from your authorized dealer.

11. Set all four tires to the recommended air pressure as indicated on
the Safety Compliance Certification Label or Tire Label located on the
B-Pillar or the edge of the driver’s door. See Vehicle loading - with and
without a trailer in this chapter for more information.

Tires, Wheels and Loading

162

Performing the TPMS reset procedure (Vehicles that have wheels
with banded pressure sensors)

TPMS reset tool

Please take the tool with the
provided Velcro

威 strip on the back

If you find that the reset tool was not provided when delivered, has been
lost or no longer functions (the battery is not replaceable), please contact
your authorized dealer as soon as possible to obtain a replacement.

To verify that your TPMS reset tool is working, press and release the
button on the center of the TPMS tool. The red light should illuminate
and remain on for approximately five (5) seconds. If the light does not
illuminate, the tool needs to be replaced.

It is recommended that you read the entire procedure before attempting.

Note: To enter the reset mode, Steps 1–6 MUST be completed within
60 seconds.

1. Place the ignition in the off position and keep the key in the ignition.

2. Press and release the brake
pedal.

Tires, Wheels and Loading

163

3. Cycle the ignition from off to on
three (3) times ending in the on
position—DO NOT start the engine.

4. Press and hold the brake pedal
for two (2) seconds, then release.

5. Turn the ignition to off—DO
NOT remove the key.

6. Cycle the ignition from off to on three (3) times ending in on. DO
NOT start the engine.
If the reset mode has been entered successfully, the horn will sound
once, the TPMS indicator

will flash and the message center will

display TRAIN LEFT FRONT TIRE.
If after repeated attempts to enter the reset mode, the horn does not
sound, the TPMS indicator

does not flash and the message center

does not display TRAIN LEFT FRONT TIRE, contact your authorized
dealer as soon as possible.

Tires, Wheels and Loading

164