Ford E-350 (2010 year). Manual — part 68

WINDSHIELD WASHER FLUID

Add fluid to fill the reservoir if the
level is low. In very cold weather, do
not fill the reservoir completely.

Only use a washer fluid that meets
Ford specifications. Do not use any
special washer fluid such as
windshield water repellent type fluid
or bug wash. They may cause
squeaking, chatter noise, streaking
and smearing. Refer to
Maintenance product
specifications and capacities in this chapter.
State or local regulations on volatile organic compounds may restrict the
use of methanol, a common windshield washer antifreeze additive.
Washer fluids containing non-methanol antifreeze agents should be used
only if they provide cold weather protection without damaging the
vehicle’s paint finish, wiper blades or washer system.

WARNING: If you operate your vehicle in temperatures below
40°F (5°C), use washer fluid with antifreeze protection. Failure

to use washer fluid with antifreeze protection in cold weather could
result in impaired windshield vision and increase the risk of injury or
accident.

CHANGING THE WIPER BLADES

1. Pull the wiper arm away from the
vehicle. Turn the blade at an angle
from the wiper arm. Press the lock
tab to release the blade and pull the
wiper blade down toward the
windshield to remove it from the
arm.

2. Attach the new wiper to the
wiper arm and press it into place
until a click is heard.

Replace wiper blades at least once per year for optimum performance.
Poor wiper quality can be improved by cleaning the wiper blades and the
windshield. Refer to Windows and wiper blades in the Cleaning
chapter.

Maintenance and Specifications

273

To prolong the life of the wiper blades, it is highly recommended to
scrape off the ice on the windshield before turning on the wipers. The
layer of ice has many sharp edges and can damage the micro edge of the
wiper rubber element.

ENGINE OIL

Checking the engine oil

Refer to the scheduled maintenance information for the appropriate
intervals for checking the engine oil.

1. Make sure the vehicle is on level ground.

2. Turn the engine off and wait 15 minutes for the oil to drain into the
oil pan.

3. Set the parking brake and ensure the gearshift is securely latched in P
(Park).

4. Open the hood. Protect yourself from engine heat.

5. Locate and carefully remove the
engine oil level dipstick.

6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.
• If the oil level is between the lower and upper holes or between

the MIN and MAX marks (depending on application), the oil
level is acceptable. DO NOT ADD OIL.

Maintenance and Specifications

274

• If the oil level is below the lower

hole or the MIN mark, add
enough oil to raise the level
within the lower and upper holes
or within the MIN-MAX range.

• Oil levels above the upper hole or the MAX mark may cause engine

damage. Some oil must be removed from the engine by an authorized
dealer.

7. Put the dipstick back in and ensure it is fully seated.

Adding engine oil

1. Check the engine oil. For instructions, refer to Checking the engine
oil in this chapter.

2. If the engine oil level is not within the normal range, add only certified
engine oil of the recommended viscosity. Remove the engine oil filler cap
and use a funnel to pour the engine oil into the opening.

3. Recheck the engine oil level. Make sure the oil level is not above the
normal operating range on the engine oil level dipstick.

4. Install the dipstick and ensure it is fully seated.

5. Fully install the engine oil filler cap by turning the filler cap clockwise
1/4 of a turn until three clicks are heard or until the cap is fully seated.

To avoid possible oil loss, DO NOT operate the vehicle with the
engine oil level dipstick and/or the engine oil filler cap removed.

Maintenance and Specifications

275

Engine oil and filter recommendations

Look for this certification
trademark.

Use SAE 5W-20 engine oil

Only use oils certified for gasoline engines by the American Petroleum
Institute (API). An oil with this trademark symbol conforms to the
current engine and emission system protection standards and fuel
economy requirements of the International Lubricant Standardization and
Approval Committee (ILSAC), comprised of U.S. and Japanese
automobile manufacturers.

To protect your engine and engine’s warranty, use Motorcraft

威 SAE

5W-20 or an equivalent SAE 5W-20 oil meeting Ford specification
WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and
durability performance meeting all requirements for your
vehicle’s engine. Refer to Maintenance product specifications and
capacities later in this chapter for more information.

Do not use supplemental engine oil additives, cleaners or other engine
treatments. They are unnecessary and could lead to engine damage that
is not covered by Ford warranty.

Change your engine oil and filter according to the appropriate schedule
listed in the scheduled maintenance information.

Ford production and Motorcraft

威 replacement oil filters are designed for

added engine protection and long life. If a replacement oil filter is used
that does not meet Ford material and design specifications, start-up
engine noises or knock may be experienced.

It is recommended you use the appropriate Motorcraft

威 oil filter or

another with equivalent performance for your engine application.

Maintenance and Specifications

276